User guide

ManualsBrandsWilbur Curtis ManualsCoffee machinesSLG

ADJUSTING THE GRINDS

This adjustment may change the volume of ground coffee

output. See Setting the Timer on page 2.

1. Empty the coffee beans from the hopper. Run grinder

to clear grinding burrs of coffee.

2. Open housing cover to locate adjusting screw (1) and

lock nut (2). Loosen lock nut.

3. Run motor during the adjustment. Turning adjusting

screw clockwise will result in a ner grind. If you hear

the grinding burrs starting to touch, immediately, back

off 1/8th turn. Turning counter clockwise will produce a

coarser grind.

4. With a screwdriver holding the adjustment screw in

place, tighten the locknut.

5. Grind some coffee beans to conrm the adjustment.

6. Replace front cover on machine.

IMPORTANT SAFEGUARDS & SYMBOLS

CAUTION: Please use

this setup procedure

before attempting to

use this grinder. Failure to follow

the instructions can result in injury

or the voiding of the warranty.

Service Manual – SLG Grinder

This appliance is designed for commercial use. Any servicing other than cleaning and maintenance

should be performed by an authorized Wilbur Curtis service center.

• Do NOT immerse the unit in water or any other liquid

• To reduce the risk of re or electric shock, do NOT open top panel. No user serviceable parts

inside. Repair should be done only by authorized service personnel.

• Keep hands and other items away from hot parts of unit during operation.

• Never clean with scouring powders or harsh implements.

SYMBOLS

WARNINGS – To help avoid personal injury Important Notes/Cautions – from the factory

QUICK START & SETUP

1. Install the grinder on a rm, level counter top in a location where it can be connected to

a grounded electrical outlet of 120VAC, rated at 15 amps.

2. Test the unit by running some whole bean coffee through the grinder. If any problems

are encountered, refer to the troubleshooting section complete at www.wilburcurtis.com

or call Technical Support at 800-995-0417.

OPERATING INSTRUCTIONS - SLG

The SLG grinder is adjusted at the factory to grind 2 to 2.5 ounces of

medium roast coffee.

1. Lift off the clear hopper lid and ll the hopper with whole coffee

beans.

2. Place a new lter into your brew cone. Slide the brew cone into the

brew cone rails on the grinder.

3. Push the START switch on the front panel. The SLG will start to

grind coffee into the brew cone.

4. Wait for the grinder motor to stop before removing the brew cone.

Wilbur Curtis Company, inC.

Models Included

SLG

ISO 9001:2008 REGISTERED

WILBUR CURTIS CO., INC.

6913 West Acco Street

Montebello, CA 90640-5403

For the latest information go to

www.wilburcurtis.com

Tel: 800-421-6150

Fax: 323-837-2410

Summary of content (6 pages)

PAGE 1
Wilbur Curtis Company, Inc. Service Manual – SLG Grinder IMPORTANT SAFEGUARDS & SYMBOLS This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an authorized Wilbur Curtis service center. • Do NOT immerse the unit in water or any other liquid • To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside. Repair should be done only by authorized service personnel.
PAGE 2
CHANGING A BROKEN SHEAR DISK 1. Unplug the power cord. 2. Open the hopper and remove any coffee beans, then open the front cover. 3. On the grind motor assembly, take out the two thumb screws (10) and remove the housing cover (6). 4. Pull out the grinding burr/feed worm assembly (2). The inner half of grinding burrs will remain within the housing. 5. Separate the shear cap (5) and shear drive (3). The broken shear disk (4) should fall out from the slot on the drive. 6.
PAGE 3
ILLUSTRATED PARTS 1 9 2 3 7 4 6 8 5 10 INDEX № PART № DESCRIPTION 1 WC-9178 HOPPER COVER, CLEAR PLASTIC 2 WC-9169 HOPPER 3 WC- 628* TIMER 4 WC-1504 CIRCUIT BREAKER 5 WC-3502* FOOT, RUBBER WITH 8-32 STUD 6 WC-6550 RAILS, BREW CONE 7 WC-9135* MOTOR, SLICING GRINDER ASSY 120V 8 WC-38027 LABEL, FRONT COVER SLG 9 WC-38339 LABEL, TIMER SLG 10 WC- 101* SWITCH, START * Recommended Parts to Stock 3
PAGE 4
ILLUSTRATED PARTS LIST GRINDER MOTOR DETAILS 7 17 16 15 14 13 12 20 11 19 18 INDEX № PART № 11 12 13 14 15 16 17 18 18A 19 20 20A WC-37284* WC-91026 WC-91024 WC-9107-6* WC-91016 WC-91017 WC-91015 WC-91045 WC-91050 WC-91021 WC-91020 WC-91051 DESCRIPTION KIT, GRINDER CHUTE NEW STYLE CAPACITOR, COFFEE GRINDER ASSY SHEAR DRIVE COFFEE GRINDER SHEAR DISK, 6 PCS CAP, SHEAR DISK GRINDERS COVER, GRINDER HOUSING W/LABEL SCREW & THRUST PIN ADJUSTING ASSEMBLY BURRS, SET CRUSH HIGH FLOW BURR, COMPLETE SET
PAGE 5
ROUGH-IN DRAWING ELECTRICAL SCHEMATIC 5
PAGE 6
Product Warranty Information The Wilbur Curtis Company certifies that its products are free from defects in material and workmanship under normal use. The following limited warranties and conditions apply: 3 Years, Parts and Labor, from Original Date of Purchase on digital control boards. 2 Years, Parts, from Original Date of Purchase on all other electrical components, fittings and tubing. 1 Year, Labor, from Original Date of Purchase on all electrical components, fittings and tubing.