FIND OUT MORE ON THE WEB. WILBURCURTIS.COM Installation Instructions, Service & Warranty Information Revised: Aug 2003 MODELS INCLUDED • TLP10 • TLP15 • TLP20 • TLP30* • TLP61 * 30 is Not UL Listed TLP DRAFT COPY DIGITAL AIRPOT BREWER Not Released. This Version Exists as File No. I:\DIAGRAMS\FRANK\FX-134.p65 C UL ® UL ® WILBUR CURTIS COMPANY • Montebello, CA 90640 ISO 9001 REGISTERED FOR THE LATEST SPEC INFORMATION GO TO WWW.WILBURCURTIS.
TABLE OF CONTENTS IMPOR IMPORTTANT SAFEGUARDS/ CONVENTIONS Important Safeguards / Conventions . . . . . . . . . . . . . . . . . . . . . . . . 2 Contents & Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Rough-in Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Quick Start & Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Brewing Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS AND UNPACKING SHIPPING CARTON CONTENTS & UNPACKING UNPACKING All products manufactured by the Wilbur Curtis Company are thoroughly inspected at the factory and are warranted to be free of all defects and faulty workmanship. These brewers are packaged for maximum protection during shipping. Make sure the shipping carton is not damaged or punctured. Unpack the carton, carefully inspecting the contents for any damage that may have occurred in transit.
QUICK START & SET-UP Your Curtis ADS System is Factory Pre-Set and Ready to Go... Right from the Carton. Following are the Factory Settings for the TLP Coffee Brewer: • Brew Temperature = 200°F • Brew Volume = Set to dispensing vessel requirements (2.2 Liters) Generally there will never be a reason to change your ADS programming. However, should you need to make slight adjustments to meet your brewing needs, programming instructions are provided later in this manual.
BREWING INSTRUCTIONS 1. Brewer should be ON (Confirm rear toggle switch is on, then press ON/ OFF button). 2. Place an empty airpot in position, under the sprayhead. WARNING: To avoid scalding, do NOT remove brew cone while brew indicator light is flashing. 3. Place a filter and ground coffee in the brewcone. Slide the brewcone into position on brew rails. 4. Wait until the READY-TO-BREW light comes on and then press the desired BREW button.
Your Curtis ADS System is Factory Pre-Set for Optimum PerSTEPS TO PROGRAMMING formance. Generally, There Will Not be a Need to Change Programming. HOT WATER Dispense Button (Orange) READY TO BREW Indicator Light (Red) ON/OFF Button (Yellow) 12 12 F12 ULL BREW ON/OFF ~ ~ READY TO BREW I/O 12 12 HALF BREW HOT WATER HALF BREW Button (Green) FULL BREW Button (Green) Changing the ADS System Program WARNING: These steps will involve working with hot water.
Brew Volume - Factory Pre-set Full Brew to 2.2 Liters The Half Brew button is always half of the brewtime of the setting of the Full Brew button. You cannot program the Half Brew. Change the brew volume of your ADS System by following these steps. Before changing the brew volume, wait until unit reaches brew temperature (Ready to Brew light comes on), insert the brewcone into place on the brewer, then place a measuring container centered beneath the brewcone.
Low Temperature Brew Lockout (Delta) - Factory Preset to Delta 1 DELTA 1 (this is factory setting) allows you to brew within 5 degrees from set temperature. This provides for consistent brew temperature and consistent water density. If Delta 1 is used, run half brew first, discard water. Program to ½" below collar of airpot (one small finger width). DELTA 2 allows you to brew within 10 degrees from set temperature. If Delta 2 is used, run half brew first and discard water.
TROUBLESHOOTING GUIDE IMPOR IMPORTTANT ANT:: Error codes are indicated by the red READY TO BREW light. If and Error Code occurs, the unit will shut down all functions including heating, water inlet, water delivery. ALWAYS confirm Error Code three times. ERROR CODES Curtis ADS Systems contain various safety features in the electronic circuitry that will shut down the functions of the unit in the event of systems faiolures. Error codes are signalled by the red READY-TO-BREW light blinking.
SYMPTOM: WATER NOT FLOWING FROM SPRA YHEAD SPRAYHEAD POSSIBLE CAUSE 14. Obstructed Sprayhead 15. Water level is too low in heating tank 16. Defective Pump 17. Defective Control Board SOLUTION Remove and inspect sprayhead. Clean and reinstall. Check water level in tank. If water is not flowing into tank, review steps 1 through 4. Contact factory. Contact factory.
ELECTRICAL SCHEMATIC Brewer Model TLP10 & TLP12 11 1/31/00 9.1 I:Diagrams\Fx-134.p65.
ELECTRICAL SCHEMATIC 12 Brewer Model TLP15 & TLP17
ELECTRICAL SCHEMATIC Brewer Model TLP20 & TLP22 13
ELECTRICAL SCHEMATIC 14 Brewer Model TLP30 & TLP32
ELECTRICAL SCHEMATIC Brewer Model TLP61 & TLP63 15
PARTS DIAGRAMS 2 6 1 11 16 10 7 3 13 5 17 A 15 8 A 16 12 9
PARTS DIAGRAMS 20 19 18 24 21 23 22 B 1234 1234 1234 1234 B 4 123 123 123 123 123 12 123 12 14 17
PARTS LIST 18 GENERAL PARTS ITEM N º PART N º DESCRIPTION 1 1A 2 3 4 5 6 7 8 9 10 11 11A 12 12A 13 13A 14 15 16 16A 17 17A 18 18A 18B 18C 19 20 21 22 23 23A 23B 24 WC-3621 WC-3316 WC-5450 WC-39321 WC-1438-101 WC-29030 WC-2962 WC-29037 WC-3765 WC-58085 WC-8556 WC- 761 WC- 771 WC-1040 WC-1042 WC- 889 WC- 860 WC-5231 WC-3503 WC- 102 WC- 103 WC- 826 WC- 856 WC-54107 WC-54123 WC-54124 WC-54127 WC-43062 WC-5851 WC-5502 WC- 523 WC- 904 WC- 917 WC- 922 WC-5310 CONE, UNIVERSAL BREW 7 1/8 BLK PLASTIC BREWCONE W
WARRANTY We hereby certify that the products manufactured by the Wilbur Curtis Company, Inc., are, to the best of our knowledge, free from all defects and faulty workmanship. The following warranties and conditions are applicable: • 90 Days for Labor and 1 Year Parts from Date of Purchase from Factory: This warranty covers all electrical parts, fittings and tubing. • 40 Months or 40, 000 Pounds of Coffee on a set of Grinding Burrs.
WILBUR CURTIS CO., INC. 6913 Acco St., Montebello, CA 90640-5403 U.S.A. Phone: 800/421-6150 (M-F 5:30A - 4:00P PST) Fax: 323-837-2410 Technical Support Phone: 800/995-0417 E-Mail: techsupport@wilburcurtis.com Web Site: www.wilburcurtis.com Printed in U.S.A. 8/03 FOR THE LATEST SPEC INFORMATION GO TO WWW.WILBURCURTIS.
