Infrared Digital Scouting Camera User’s Manual Model # W4E
Includes USB Cable 2 - Bungee Cords Flextime Player Software Camera Unit NOTE: Flextime Player Software is optional. Flextime files can be played by using most media players.
Features RESOLUTION FLASH FLASH RANGE SENSOR SENSOR RANGE IMAGE FORMAT MEMORY USB IMAGE RESOLUTION POWER SUPPLY AUXILIARY POWER BATTERY LIFE ONBOARD POWER HOUSING MOUNTING REDUX MAX: 4 MP 24 High Intensity Infrared LED’s up to 60 feet Passive Infrared Sensor (PIR) Motion and Heat up to 60 feet JPEG - Digital Still / AVI - Digital Video up to 64GB SD Card (not included) 5-PIN Mini USB style - included High (4MP) Medium (2MP) Low (1.
Installing Batteries 1. Open the door at the bottom of the camera by unlatching the locking tabs. Open Illustration A 2. page 3 With the camera facing open, open the battery compartment cover by sliding the latch to the left.
3. 4. Close battery compartment cover. To latch the cover simply pull the latch slightly to the left as you close the battery compartment cover. 5. Load SD memory card (up to 64GB not included) into the SD card slot with the connectors facing down. With the bottom of the camera towards you, Make sure to insert the batteries into the camera with the positive ends towards you where marked positive and the negative ends towards you where marked negative.
Power On 1. 2. Test Mode To turn the unit ON press and release the power button. Check the battery level icon to ensure the batteries just installed contain the proper charge level. If so, you are ok to proceed with camera use. Time/Date Location Trigger Flextime PIR Mode PIR Active PIR Sense Picture Resolution Delay PIR Mode P1 Still 24Hr Hi Regular Hi 15s 30s Flextime P2 Video Day Med Wide Med 1m Both Interval Night Lo Lo 2m 5m 10m NOTE: LCD cycle through camera information.
Power Save 1. 2. After 30 seconds without any buttons being pushed, the LCD will turn off and camera enters into Power Save or Ready Mode. Setting Time 1. To change date and time, start by pressing and release the center navigation button to set the hour. Time/Date Location Trigger Flextime PIR Mode PIR Active PIR Sense Picture Resolution Delay The LCD screen can be awakened by pressing the Power button briefly.
Setting Date 1. Press the center navigation button after setting the minute to change the Day. Time/Date Location Trigger Flextime PIR Mode PIR Active PIR Sense Picture Resolution Delay 2. page 7 Flextime P2 Video Day Med Wide Med 1m PIR Mode P1 Still 24Hr Hi Regular Hi 15s 30s Flextime P2 Video Day Med Wide Med 1m 1. Night Lo Lo 2m 5m 10m 2. Both Interval Night Lo Lo 2m 5m 3.
Trigger 1. Flextime Press the center navigation button while Trigger is selected. The highlighted option will be blinking. Time/Date Location Trigger Flextime PIR Mode PIR Active PIR Sense Picture Resolution Delay 2.
FLEXTIME selected Flextime period: 1. 15 min before Sunrise to 1 hour after Sunrise. 2. 1 hour before Sunset to 15 min after Sunset Flextime period: 1. 15 min before Sunrise to 1 hour after Sunrise. 2. 1 hour before Sunset to 15 min after Sunset Camera is inactive before and after Flextime periods. P1 INACTIVE Flextime is active twice a day. 15 MINUTES AFTER FLEX SUNSET TIME 15 MINUTES BEFORE SUNRISE FLEX TIME INACTIVE 1 HOUR AFTER SUNRISE Camera is in PIR mode before and after Flextime periods.
PIR Mode 1. PIR Active Press the center navigation button while PIR Mode is selected. The highlighted option will be blinking. Time/Date Location Trigger Flextime PIR Mode PIR Active PIR Sense Picture Resolution Delay 2. PIR Mode P1 Still 24Hr Hi Regular Hi 15s 30s Flextime P2 Video Day Med Wide Med 1m Night Lo Lo 2m 5m PIR Mode P1 Still 24Hr Hi Regular Hi 15s 30s Flextime P2 Video Day Med Wide Med 1m 10m Both Interval Night Lo Lo 2m 5m 10m VIDEO: The camera takes 30 second videos. 2.
PIR Sensitivity 1. Press the center navigation button while PIR Sense is selected. The highlighted option will be blinking. Time/Date Location Trigger Flextime PIR Mode PIR Active PIR Sense Picture Resolution Delay 2. PIR Mode P1 Still 24Hr Hi Regular Hi 15s 30s Flextime P2 Video Day Med Wide Med 1m PIR Mode P1 Still 24Hr Hi Regular Hi 15s 30s Flextime P2 Video Day Med Wide Med 1m Lo 2m 5m 10m Both Interval Night Lo Lo 2m 5m 10m HI: The PIR detects the smallest Open movement.
Resolution 1. Delay Press the center navigation button while Resolution is selected. The highlighted option will be blinking. Time/Date Location Trigger Flextime PIR Mode PIR Active PIR Sense Picture Resolution Delay 2.
Power Port Power Off 1. To turn the unit off, first wake up the LCD screen and then depress and hold the power button until the LCD turns off. 1. WGI Cameras come standard with an external power port. You must open the weather resistant cover and use a Wildgame Innovations 6 Volt camera battery accessory.
Mounting 1. When mounting to a tree, first latch the 2 bungee cords through the mounting holes on the left or right side of the camera. Then, stretch the cords around the tree and latch the other ends of the bungee cords through the mounting holes on the opposite side of the camera. Important Once you connect the camera to your computer via the USB cable/ports, the camera will then draw power from the computer.
Retrieving Images (SD Card in Camera) Method 1: Leave SD card in camera A. First, make sure that the camera is powered OFF. Next, plug the USB cable into the camera and then into the USB port on your computer. Once this is complete (in this order only), then power the camera ON. B. Once complete, your computer may automatically launch “AutoPlay”, a window recognizing a new Removable disk (the camera). C. If so, it should give you three selections: 1. Import pictures 2. View pictures 3.
Retrieving Images (SD Card reader) Method 2: Remove SD card and use card reader left of your screen and select “Computer”. The summary view will then be illustrated on the right hand side of the window where A. First, remove the SD Card from the by the “Devices with Removable Storage” camera unit itself by pressing on it to where will be listed. The computer will recognize it automatically ejects. the reader as “Secure Digital Storage B. Next, insert the SD card into your SD Device”.
Warranty DISCLAIMERS WGI Innovations, LTD. is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY You must register your product warranty online at www.wildgameinnovations.com. Follow the on screen directions to complete the process. WGI Innovations, LTD.
FCC FCC STATEMENT Product Name: Game Trail Camera Trade Name: Wildgame Innovations Model# W4E This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Wildgame Innovations” and the “Button Logo” are TM trademarks of Wildgame Innovations, LLC. “Sport Responsible” , “Redux” and “Flextime” are TM trademarks of WGI Innovations, LTD.