User's Manual

DLT 300 3.0 Digital Transceiver and DLR 360 3.0 Digital Receiver
14
Address Conrmation
Press the MENU button twice for the M1 and M2, once for GSTs. The address for the DLT will be displayed for two seconds.
NOTE: Every DLT MUST have its own address and all must be assigned to the same group.
Quick Group Change
“Groups” apply to 2-way Mode only.
1. With the DLT powered ON, push and hold the Group button
until the GROUP indicator on the screen
starts blinking and the light above the Group button comes on (Figure 5).
2. Change groups by pushing the Up button
or the Down button . If no buttons are pushed, the
Quick Group Change feature will time out after 5 seconds.
3. Push the Group button
once to exit the Quick Group Change function, or wait for 5 seconds.
Push-to-Talk (Ptt) and Push-and-Latch (PNL)
This feature allows the user to choose between Push and Latch (PnL) or Push to Talk (Ptt). The default is PnL.
In PnL mode, when the TALK button
is pressed and released, it stays in talk mode until the TALK
button is pressed and released again.
In Ptt mode, the TALK button must be held down while speaking, and when released, it shuts o.
The DLT must be set up as a Guest unit, in 2-way mode, prior to performing these steps.
1. With the DLT powered ON, press and hold the Up button
and the Down button
simultaneously for 2 seconds to enter programming mode.
2. Push the Power/Menu button until the TALK indicator is ashing and either “PnL” is or “Ptt” is
displayed. (Figure 6).
3. Use either of the -/+ buttons
to switch between “PnL” and “Ptt”
4. Press and hold the Up button
and the Down button simultaneously for 2 seconds to exit programming mode.
Side Tone Adjustment
This gives the user the ability to change the volume of their own voice heard in the headset (side tone).
1. With the DLT powered ON, press and hold the Up button
and the Down button simultaneously
for 2 seconds to enter programming mode.
2. Push the Power/Menu button until “St:” is displayed. See Figure 7.
3. Use either of the -/+ buttons
to choose between Stt:0 (O), St:1 (-6dB) (default), or St:2
(-12dB).
4. Press and hold the Up button
and the Down button simultaneously for 2 seconds to exit
programming mode.
Talk “O” Double-Beep Indication Limit
The user hears an audible “double-beep” sound when the TALK button is turned o. This is heard in the headset of the user only; it is
not transmitted. On the DLT, as the headset volume is increased, the beep volume will increase until the headset volume reaches 37,
then the beep volume will stop increasing. (Note: On the DLT 100 the beep volume continued to get louder as the headphone volume
was increased, with no limit.)
FIGURE 5
FIGURE 6
FIGURE 7
Secure Key Code fig. 1
Original (save)
Secure Key Code fig. 2 SLOC fig. 3 Tone Control fig. 4 Quick Group Change fig. 5
Ptt & PnL fig. 6 Ptt & PnL fig. 6
Side Tone fig. 7
A530
Secure Key Code fig. 1
Original (save)
Secure Key Code fig. 2 SLOC fig. 3 Tone Control fig. 4 Quick Group Change fig. 5
Ptt & PnL fig. 6 Ptt & PnL fig. 6
Side Tone fig. 7
A530
Secure Key Code fig. 1
Original (save)
Secure Key Code fig. 2 SLOC fig. 3 Tone Control fig. 4 Quick Group Change fig. 5
Ptt & PnL fig. 6 Ptt & PnL fig. 6
Side Tone fig. 7
A530
Secure Key Code fig. 1
Original (save)
Secure Key Code fig. 2 SLOC fig. 3 Tone Control fig. 4 Quick Group Change fig. 5
Ptt & PnL fig. 6 Ptt & PnL fig. 6
Side Tone fig. 7
A530