User manual

13
Personal PA
®
DSP FM Wideband Transmitter
Quick Setup Instructions
1. Position the PPA T45 transmitter near the sound system or mixer from which it will receive audio. It should be free from metallic
objects that might interfere with the antenna signal.
2. If the transmitter is free-standing (not rack-mounted), install the ANT 025 whip antenna. Gently thread the ANT 025 onto
the stud recessed in the hole on the top of the transmitter (Figure 2) and extend it all the way. The transmitter can be rack-
mounted (1RU) with the optional RPK 005 Rack Mount Kit - in this case the whip antenna cannot be used; instead use the rear
“RF 75Ω ANT” coaxial jack for remote antenna mounting with a coaxial cable (Figure 5).
3. Connect the power supply to the Power Supply connector (Figure 2, page 5) located on the back of the T45. Press in the
power button on the front of the T45. The power button should light up, and the “RF” green LED indicator should illuminate. If
not, go back and check the power connections.
4. Choose and congure the audio source. The audio source must be congured in the menu before plugging the source
into the jack. Push the Menu button and push the “>” button once to display “AUDIO SOURCE” on the screen. Push the “>”
button to access the audio sources. Using the “^” or “v” menu buttons (Figure 2), choose between “ANALOG LINE IN”, “MIC”,
“PHANTOM MIC +12V”, “DIGITAL AES/EBU”, or “DIGITAL S/PDIF”. When the desired audio source is displayed, it is active, so
press the Menu button to exit the menu (Figure 7).
5. Push the power button to turn the unit off. (Figure 7)
6. Connect the audio source to the audio input jack on the rear of the T45 (the jack that was chosen in step 4). (Figures 2, 6)
7. Push the power button to turn the unit on. (Figure 7)
8. With the audio source playing, adjust the Audio Level on the T45 so that the green “0 dB” LED generally lights and the red “+9
dB” LED lights occasionally. To do this, use the Hot Buttons while on the main info screen. Press the “^” button to increase the
audio level in 1.0 dB steps, or press the “v” button to decrease the audio level in 1.0 dB steps.
9. Select an Audio Preset. The T45 has three pre-congured Audio Presets to choose from: Hearing Assist, Music, and Voice. A
Custom preset is also available. The performance of the T45 is optimized for each of the pre-congured Audio Presets. Using
the menu and control buttons on the front of the T45 (Figure 7), push the Menu button, the display will change to show “Audio
Settings”. Use the forward “>” button to display “Audio Source” in the selection box. Push the down “v” button twice to show
“Audio Presets”. Now press the “>” button to display the list of Presets. Use the “^” and “v” buttons to alternate between
“Hearing Assist”, “Music”, “Voice” and “Custom” selections. When the desired Audio Preset is displayed, it is active, so press
the Menu button to exit the menu, or, if “Custom” is desired, push the “>” button to enter the custom settings.
10. Set the Transmitter Channel. The T45 is shipped from the factory with the channel/frequency set to Ch.1 (72.1 MHz). To change the
channel/frequency, while on the main info screen, use the hot buttons “<” and “>” to change channels. (Figure 7)
11. Listen with an FM receiver (see compatible Williams Sound receivers towards the back of this manual). Install the batteries,
plug in the earphone, turn on the receiver, choose the correct channel and walk around the listening area. The signal should be
clear and quite loud when the volume is turned up.
12. (T45NET only) Connect a CAT5e Ethernet cable from your local area network, wi- router, or PC to the connector on the
T45NET labelled “Ethernet”.
13. (T45NET only) Once the T45 detects an active network is present, the “X” will disappear from the computer icon on the main
info screen, indicating that it has connected to the network. The main info screen will display the text “IP:\”, where the last
character “\” will spin, while the T45 is acquiring a DHCP address. Once acquired, (usually takes less than a minute), the T45’s
IP address will be displayed in the “Add-on module” part of the Main Info Screen. (Figure 8)
14. (T45NET only) Open a web browser (i.e. Internet Explorer, Mozilla Firefox, Google Chrome, Safari, etc.) on a computer or
mobile device that is also connected to the same local network as the T45.
15. (T45NET only) In the address bar of the browser, type in the IP address that is shown on the front of the T45NET’s main
info screen, and push the enter key on the keyboard. (Note: it is not necessary to type “http://” or “www.” preceding the IP
address, just the characters following “IP:”, including the periods)
16. (T45NET only) The browser will open the T45NET’s web page, displaying a “Log In” button (Figure 17). Click the log-in
button and enter the user name “admin” and the default password “admin”.
17. (T45NET only) The web browser will now show the T45NET’s Home Page (Figure 18), which shows the current T45NET
status info. The tabs at the top navigate to different pages that allow adjustment of the T45NET’s settings.
IMPORTANT: The FM receiver being used will need to be on the same channel/frequency as the T45 transmitter.