WIR RX22-4 SoundPlus® 4-Ch Infrared Receiver Instructions For Use and Care MAN127F
Operating Instructions 1. Open battery compartment door on back of receiver by pressing the tab down. 2. If using rechargeable NiMH batteries, slide the Alkaline/ NiMH switch to the NiMH position. Default setting is Alkaline for non-rechargeable batteries. See Figure 1. Figure 1: Battery selection switch CAUTION: RECHARGE ONLY NIMH BATTERIES ALKALINE/ NiMH SWITCH – AA + + AA – A192 3. Insert 2 AA batteries over the fabric strip. Note correct polarity (+/-).
Figure 2: WIR RX22-4 Control Panel HEADPHONE JACK "ON"/LOW BATTERY INDICATOR CHANNEL SELECTOR KNOB ON/OFF, VOLUME CONTROL SWITCH A131 4. Insert earphone or neckloop into the headphone jack. 5. Turn the receiver on by rotating the Volume control knob. The ON indicator should illuminate RED. 6. Select a channel by turning the channel selector knob on the control panel. Choose between 4 standard frequencies: 2.3 MHz (Ch.1), 2.8 MHz (Ch. 2), 3.3 MHz (Ch.3), or 3.8 MHz (Ch. 4).
Lanyard Clip Installation For hands-free operation of the RX22-4 receiver, use the provided lanyard clip to secure the unit on your lanyard, pocket or pants. To Install: Position the lanyard clip on the rear of the RX224 receiver as shown in Figure 3A. Turn the lanyard clip 180° left or right as shown in Figure 3B. The lanyard clip is now installed and ready for use. To Remove: Turn the lanyard clip 180° so the edge points toward the top of the unit as shown in Figure 3A.
Battery Information The WIR RX22-4 uses 2 AA batteries. We recommend using Williams Sound Alkaline batteries (BAT 001) or Rechargeable batteries (BAT 026) for longer battery life than other brand batteries. Low Battery Indicator The “On” indicator on top of the unit will flash to indicate low battery. Multi Charger CHG 3512 This optional charger is ideal for customers using rechargeable batteries. It will charge up to 12 receivers at one time. See our website or call us for ordering information.
Customer Service If you experience difficulty with your system, call toll-free for Customer Assistance: 1-800-843-3544 (U.S.A.) or +1 952 943 2252 (Outside the U.S.A.) If it is necessary to return the system for service, your Customer Service Representative will give you a Return Authorization Number (RA) and shipping instructions. Pack the system carefully and send it to: Williams Sound LLC. Attn: Repair Dept.
Limited Warranty Williams Sound products are engineered, designed and manufactured under carefully controlled conditions to provide you with many years of reliable service. Williams Sound warrants the WIR RX22-4 receiver against defects in materials and workmanship for five (5) years. During the first five years from the purchase date, we will promptly repair or replace the WIR RX22-4 receiver. Earphones, headphones, batteries, cables, carry cases, and most other accessory products carry a 90-day warranty.
Safety Information Hearing Safety CAUTION! This product is designed to amplify sounds to a high volume. To protect your hearing and the hearing of others: 1. Make sure the unit is OFF or the volume is turned down before putting on the earphones. 2. Set volume level at the minimum setting you need to hear. 3. Do not allow children or other unauthorized persons to have access to this product.
Medical Device Safety CAUTION! Before using this product with a pacemaker or other implantable medical device, consultant your physician or the manufacturer of the device to make sure that you are using this product in accordance with their safety guidelines. Recycling Instructions Help Williams Sound protect the environment! Please do not dispose of equipment or used batteries in the household trash. Take the equipment to an electronics recycling center or return to the factory.
System Specifications Personal PA® RX22-4 Receiver Dimensions: 4.1” L x 2.85” W x 1.2” H (104.1 mm x 72.4 mm x 30.4 mm) Weight: 4.5 oz (127 g) with batteries Battery Type: 2x AA, alkaline (BAT 001) or NiMH (BAT 026) Battery Life: Alkaline: 60 hours, NiMH: 30 hours/charge Charging Contacts: For use only with CHG 3512 Carrier Frequency: Channel 1: 2.3 MHz, Channel 2: 2.8 MHz Channel 3: 3.3 MHz, Channel 4: 3.
