Instruction manual

I m ..u,tc.us,., or,o.o,,i. I
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell around the appliance area
for gas. Be sure to smell next to the floor because some
gas Is heavier than sir and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appllancs.
• Do not touch any eieotdc swifch; do not use any
phone In your building.
• Immediately cell your gas supplier from s neighbor's
phons. Follow the gas suppiier's Instructions.
C.
D°
• If you cannot reach your gas supplier, call the fire
department.
Use only your hand to push In or turn the gas control
knob. Never use tools. If the knob will not push in or
tum by hand, don't try to repair it, ceil n qusiified serv-
Ice tochnlcien. Force or attempted repair may result In a
fire or explosion.
Do not use this appliance if any part has been under
water. Immediately cell n qusliflnd asrvlce tochniclcn to
Inspect the appliance and to replace any part of the
control systom and any gas control which has been
under mr.
OPERATING INSTRUCTIONS
1. STOP! Resd.the safety Information above.
2. Turn off all electric power to the appliance (if applicable).
3. Open control access panel.
4. Push In gas control knob slightly and turn
clockwlse/-"_ to "OFF."
TEMPERATURE DIAL
KNOB SHOWN
IN "OFF"
POSITION
NOTE: Knob cannot be turned from "PILOT" to "OFF"
unless knob 18 pushed in slightly. Do not force.
5. Wait five (5) minutes to clear out any gas, then smell for
gas, Including near the floor. If you then smell gas, sfopi
Follow "B" In the safety Informstlon above. If you don't
smell gas, go to the next step.
6. Loosen wlngnot and open the pilot observation door (It
equipped).
7. Find pilot--follow metal tube from gas control. The pilot is
mounted on side of bumer.
8. "Ibm knob on gas control N
counterclockwlas
to "PILOT."
9. Push In control knob all the
way and hold in. Immediately
light the pilot.
THERMO- PILOT
COUPLE BURNER
Continue to hold the control knob in for about one (1)
minute sitter the pilot Is lit. Release knob and it will pop
back up. Pilot should remain lit. If it goes out, repast steps
5 through 9.
• If knob does not pep up when released, stop and
Immedlntoly cell your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to "OFF" and cell your service
technfolnn or gas supplier.
10. Close pgot olmervation door, tighton wlngn_ (if equipped).
11. Turn gas control knob counterclnckwlasl( _to "ON".
Burner Is now under control of the thermostatic canning
element. Tum temperature dial (numbered 1 through 8)
counterclockwise I_ toward 8 to obtain desired
temperature.
12. Close control socese panel.
13. "rum on MI electric power to the appliance
(If ppgWlcehlo).
TO TURN OFF GAS TO APPLIANCE
1. Tum off ell electric power to the appliance If serv-
Ice Is to be performed (if applicable).
2. Open control access panel.
3. Push In gas control knob slightly end turn
clockwise _ to "OFF." Do not force.
4. Close control access panel.
WARNING: DUE TO HIGH SURFACE TEMPERATURES -- KEEP CHILDREN, CLOTHING,
FURNITURE OR ANY COMBUSTIBLE MATERIAL AWAY FROM FURNACE.
IMPORTANT: KEEP BURNER AND CONTROL COMPARTMENT CLEAN.
DIAGRAM FOR BUILT-IN THERMOSTAT MODELS
CONNECTION WIRING
VENT _ I--I]]'ERMOCOUPLE
-%_UT OFF OE'VIC_ U .[_
BLACK
GAS VALVE
I
-- FACTORY_RED LOWVOLTAG_
NO'W.S:W AHYOF 15EO_NAL _ AS
_PP_9 _ IH£N=RJ/_¢[INSl"
Ik_l.A'lION,1_" @.AWM¢¢PP£R
_ CG_I4_'I]G_SIJE NO,10 A14_
R_OTE BULB
_11_