Installation & Assembly
(L) Chain (1)
nd link(G). Raise the fixture (J) and
(J) Fixture(1)
(M) Tube(1)
(J). 3. Carefully hook tube (M) onto fixture body
tt maximum E26Type A bulbs This fixture has been rated for up to six (1) 60-wa
(A) Wire Nut(3)
PARTS ENCLOSED
(B) Crossbar(1)
(C) Mounting Screws(2)
(D) Ceiling Loop(1)
(E) Canopy(1)
(F) Lock Collar(1)
(G) Chain End Ring(1)
(H) Top Ring(1)
CARE INSTRUCTIONS:
Wipe all surfaces with a soft dry cloth. Do
not use any harsh cleaners (including
ammonia-based products) or abrasives, as
they will damage the finish.
IMPORTANT SAFETY INSTRUCTIONS:
WE RECOMMEND INSTALLATION BY A LICENSED ELECTRICIAN.
(not included). To avoid the risk of fire, do not exceed the recommended wattage.
WARNINGS:
1. Do not remove the lamp from its packaging by pulling on the power cord, as a bad
connection may result.
2. Do not connect electricity until your lamp is fully assembled.
3. To reduce the risk of fire, electrical shock, or personal injury, always turn off lamp and
allow it to cool prior to replacing light bulb.
4. Do not touch bulb when fixture is turned on or look directly at lit bulb.
5. Keep flammable materials away from lit bulb.
6. This lighting fixture contains lead, a chemical known to the State of California to cause
cancer, birth defects and other reproductive harm. Wash hands after installing, handling,
cleaning or otherwise touching this light fixture.
TO ASSEMBLE:
1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER!
2. Carefully remove all parts from the box and remove all plastic covering.
4. Install the crossbar (B) with ceiling loop (D) to outlet box by using mounting screws (C)
provided.
5. Put canopy (E) to ceiling loop, and secure with lock collar (F).
6. Using the dimensions of the fixture as a guide, shorten the chain (L) as needed using a
pair of chain pliers.
7. Take into consideration that you will use the chain end link (G) to mount the chandelier
once you have removed the excess chain.
8. Unscrew the threaded collar on the chain end link(G). Attach the chain to the ceiling loop
(D). Close threaded collar to secure the chain(L).
9. Unscrew the threaded collar on the other chain e
attach chain end link (G) to the top ring (H). Close the threaded collar to secure the fixture
body.
10. Unwrap the wiring from the top of the fixture body. Weave the power supply cord and the
ground wire through the chain (L).
11. When you reach the canopy and ceiling loop, measure the wires and cut. Be certain to
leave enough to connect inside the canopy.
12. Strip the insulation back on the two power supply wires about 5/8”.
13. Twist the power supply and ground wires together and push through the center hole in the
ceiling loop.
14. Loosen the clock collar (F) and let the canopy (E) slip down the chain carefully.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY
WILL BE COMPROMISED.
15. Connect the Ground (bare) fixture wire with the ground (usually bare) wire from ceiling box
using wire nut (A). If your house does not have ground wire, then attach this wire to the
green grounding screw inside of outlet box.
IT IS IMPERATIVE THAT THE J-BOX IN YOUR HOME BE PROPERLY
GROUNDED.
16. Connect the Neutral fixture wire with the Neutral (usually white) wire from ceiling box using
wire nut (A).
17. Connect the Hot (smooth edge, markings, or black) fixture wire with the Hot (usually black)
wire from outlet box using wire nut (A).
18. Tuck these wire connections neatly into ceiling loop (D) to secure.
19. Put canopy (E) to ceiling loop, and secure with lock collar (F).
20. Install the light bulbs (not included) into sockets.
21. Installation is complete, turn on power at fuse or circuit breaker.