Specifications

ManualsBrandsWilson Electronics ManualsTelephone271245

Amplifier

Installation

ide

stallatio

stallat

Mobile Wireless

Dual-Band

Cellular / PCS

Ampliﬁ er

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1

How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2

Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3

Installing a Wilson Outside Antenna · · · · · · · · · · · · · · · 4

Installing a Wilson Ampliﬁ er · · · · · · · · · · · · · · · · · · · · · · 5

Installing a Wilson Inside Antenna (Wireless) · · · · · · · · 6

Installing a Wilson Inside Antenna (Attached) · · · · · · · · 7

Powering Up a Wilson Ampliﬁ er · · · · · · · · · · · · · · · · · · · 8

Warnings and Recommendations · · · · · · · · · · · · · · · · · 9

Understanding the Ampliﬁ er Lights · · · · · · · · · · · · · · · · 10

Ampliﬁ er Speciﬁ cations · · · · · · · · · · · · · · · · · · Back Cover

Wilson

Electronics, Inc.

Warning: This manual contains

important safety and operating information.

Please read and follow the instructions

in this manual. Failure to do so could be

hazardous and result in damage to your

ampliﬁ er.

Summary of content (12 pages)

PAGE 1
Amplifier Installation stallat stallatio Guide Mobile Wireless Dual-Band Cellular / PCS Amplifier Contents: Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1 How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3 Installing a Wilson Outside Antenna · · · · · · · · · · · · · · · 4 Installing a Wilson Amplifier · · · · · · · · · · · · · · · · · · · · · · 5 Installing a Wilson Insid
PAGE 2
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson’s 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 1-Year Warranty Wilson Electronics amplifiers are warranted for one (1) year against defects in workmanship and / or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
PAGE 3
Installation Instructions for the Following Wilson Amplifier: Mobile Wireless Dual-Band Amplifier Model # 271245, Part # 801201 FCC ID: PWO8012SM IC: 4726A-8012SM The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Inside this Package Wireless amplifier Low-profile antenna (Option A - see p. 6) DC plug-in power supply Universal Connector (Option B - see p.
PAGE 4
Before Getting Started This guide will help you properly install Wilson’s dual-band, mobile wireless amplifier. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment.
PAGE 5
Installing a Wilson Outside Antenna To receive the best cell signal, select a location in the center of the vehicle’s roof 12 inches away from any other antennas and free of obstructions. Follow the specific antenna installation instructions included with the outside antenna (sold separately). ! Warning: Do not use any type of glassmount antenna with this amplifier. The outside and inside antennas must be shielded from each other to prevent oscillation. The outside antenna must be installed vertically.
PAGE 6
Installing a Wilson Amplifier ! Warning: Do not plug in the DC power supply until the outside and inside antenna cables are attached to the amplifier. Select a location to install the amplifier that is away from excessive heat, direct sunlight or moisture and that has proper ventilation. Recommended installation locations are: • Under the seat • In the trunk • Under the dash Run the cable from the outside antenna and attach it to the FME-Male connector labeled “outside antenna” on the amplifier.
PAGE 7
Option A (Wireless) Installing a Wilson Inside Antenna Low-profile Antenna Install the low-profile inside antenna 8-12 inches from where the cell phone or cellular data card will be used. Amplifier ! Warning: Do not install the low-profile antenna within four inches of metal. (Metal found inside the vehicle’s seat will not affect the antenna’s performance.) Place the inside antenna on the side of the driver’s seat for maximum performance.
PAGE 8
Option B (Attached) Installing a Wilson Universal Connector Amplifier Universal Connector The universal connector must be placed directly on the cell phone or cellular data card to work properly. Attach the universal connector to the cell phone or cellular data card with the VELCRO® included in the package. IMPORTANT: The adhesive of the gray Velcro patch that adheres to the back of your phone needs time to “cure.
PAGE 9
Powering up a Wilson Amplifier Make sure both the outside and inside antenna cables are connected before powering up the amplifier. Connect the power cable from the DC plug-in power supply to the amplifier marked “Power” and insert the large end into DC power socket (the cigarette lighter outlet.) Carefully insert the power cable. ! Warning: Use only the power supply provided in this package. The power supply must be 6 V DC. The amplifier may remain on all the time.
PAGE 10
Warnings and Recommendations Warning: In a wireless installation, do not plug the amplifier directly into the cell phone or cellular data card using an antenna adapter. It will damage the cell phone or cellular data card. Warning: Do not plug in the DC power supply until the outside and inside antenna cables are attached to the amplifier.
PAGE 11
Understanding the Amplifier Lights The power light PWR will turn green when the amplifier is successfully powered up. When the 800 MHz or 1900 MHz lights are lit green, the amplifier is amplifying the outside signal. If one or both frequency lights turn red, oscillation is occurring and the amplifier has powered down. The outside antenna needs to be moved farther from the inside antenna.
PAGE 12
Amplifier Specifications Dual Band 800/1900 MHz Specifications 271245 / 801201 FME-Male 50 ohms 5.6 x 3.6 x 1.7 inch or 14.2 x 9.1 x 4.4 cm 1.44 lbs or 0.