A WILSON ELECTRONICS BRAND DRIVE REACH PROFESSIONAL VEHICLE CELLULAR SIGNAL BOOSTER KIT User Manual NEED HELP? support.weboost.com 866.294.
______ Index Package Contents 1 STEP 1: Mount Outside Antenna & Route Cable 2 STEP 2: Mount Inside Antenna 6 STEP 3: Wiring The Power Supply To Vehicle Battery 7 STEP 4: Connect Coax Cables To Booster 8 STEP 5: Connect Power Supply To Booster 9 Light Patterns 10 Troubleshooting 11 Safety Guidelines 12 Specifications 13 Warranty 14
________ Package Contents Drive 4G-X Booster & Bracket Optional Cable Outside NMO Antenna + Connector Mounting Cable 4G In-Vehicle Antenna Power Supply Protective Tape For Installation DRIVE 4G-X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 1
______ Step 1: Mount Outside Antenna & Route Cable Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 12 inches away from any other antennas • At least 6 inches away from any windows (for best performance install on top of vehicle) Mount the outside antenna by placing on top of vehicle. NOTE: Drill and 3/4” hole saw drill bit required. 6 in.
______ (STEP 1 cont.) See diagrams below for NMO Outside Antenna installation. vehicle surface Once you have determined the best location for the antenna, place the Protective Tape on the vehicle in the desired location. Protective Tape Using a 3/4” hole saw, drill hole in the center of the protective tape. 3/4” bit Protective Tape remove collar insert through hole After hole has been drilled, insert NMO Mounting Cable through (SMA connector end first) and remove collar.
______ (STEP 1 cont.) Position threads of the cable mount above vehicle surface. Apply included silicone grease to the o-ring on the collar then screw the collar to the base mount. Ensure the mount is centered in the hole and tighten with wrench. screw collar to base mount apply silicone grease Before attaching the antenna, clean the area around the mount. Apply a thin layer of silicone grease to the threads, only, of the NMO mount and to the o-ring on the antenna.
______ (STEP 1 cont.) Route NMO Outside Antenna cable inside the vehicle. For a professional installation we recommend routing the cable under the headliner and down through the side trim panel to the desired booster location on the floor of the vehicle.
______ Step 2: Mount Inside Antenna Identify a place to mount the 4G In-Vehicle Antenna, either on the side of the seat or on the dash and mount. The location should be at least 18 inches but no more than 36 inches from where the cellular device will be used. Adhesive and Velcro® mounting options are included.
______ Step 3: Wiring The Power Supply To Vehicle Battery Use steps below as a draft/template of the general install of the power supply. 1 Before connecting the power supply, disconnect the vehicle battery leads to avoid any electrical shocks during installation. 2 Locate a place where cables are already running through the firewall (rear wall of engine bay) to the inside of the cabin. 3 Locate the same firewall hole from step 2 in the inside of the vehicle cabin.
______ Step 4: Connect Coax Cables To Booster Connect the cable from the NMO Outside Antenna to the port labeled “Outside Antenna” on the Drive 4G-X booster. NOTE: Bracket can be used to fasten booster in a specific location if desired. from NMO Outside Antenna Connect the cable from the 4G In-Vehicle Antenna to the port labeled “Inside Antenna” on the booster.
______ Step 5: Connect Power Supply To Booster Connect the power supply cord to the end of the Drive 4G-X labeled “Power.” Congratulations! Once your booster is running please allow some time for your phone to adjust to your new signal. NOTE: Do NOT connect the power to the Signal Booster until you have connected both the Inside and Outside Antennas.
______ Light Patterns Solid Green This indicates that your booster is functioning properly and there are no issues with installation. Blinking Red, Then Solid Green This indicates that one or more of the booster bands has reduced power due to a feedback loop condition called oscillation. This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary.
______ Troubleshooting FIXING BLINKING OR SOLID RED ISSUES This section is only applicable if the booster is red or blinking red and you are not experiencing the desired signal boost. 1 Unplug the Booster’s power supply. 2 Relocate the inside and outside antenna further from each other. The objective is to increase the separation distance between them, so that they will not create this feedback condition discussed before. 3 Plug power supply back in. 4 Monitor the indicator light on your booster.
______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 150 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures in excess of that range. All inside low profile antennas must have at least 1.5’ separation distance from all active users.
______ Specifications Drive Reach Model Number 4600555 FCC ID: PWO460055 IC: 4726A-460055 Connectors SMA-Female Antenna Impedance 50 Ohms Frequency 698-716 MHz, 729-746 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Power output for single cell phone (Uplink) dBm 700 MHz Band 12/17 27.3 700 MHz Band 13 27.1 800 MHz Band 5 27.0 1700 MHz Band 4 28.4 1900 MHz Band 2 27.7 Power output for single cell phone (Downlink) dBm 700 MHz Band 12/17 5.0 700 MHz Band 13 5.
2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.
