Installation Guide

ManualsBrandsWilson Electronics ManualsComputers & AccessoriesQuint Band Signal Booster

ENGLISH

Contents:

How Cellular Boosters Work .........................................1

Install Overview ...................................................1

Kit Options .......................................................2

Installation Diagram .............................................3 & 4

Outside Antenna Installation .........................................5

Installing the Inside Antenna(s) .......................................7

Installing The Signal Booster .........................................7

Finding The Strongest Signal ........................................8

Post Install Setup / LCD Screen ......................................9

Warnings and Recommendations ....................................12

Warranty .......................................................14

Specifications ............................................Back Cover

Note: This manual contains important safety and operating information. Please read and follow the

instructions in this manual. Failure to do so could result in damage to your Signal Booster.

Appearance of device and accessories may vary.

INSTALLATION GUIDE

In-Building

SmarTech

Cellular Signal Boosters

PRO

PLUS

™

PRO

SERIES

BU-GDE000096-003_050620.indd 1BU-GDE000096-003_050620.indd 1 5/6/2020 3:05:42 PM5/6/2020 3:05:42 PM

Summary of content (16 pages)

PAGE 1
PRO SERIES INSTALLATION GUIDE ENGLISH PRO 70 PLUS ™ In-Building SmarTech ® Cellular Signal Boosters Contents: How Cellular Boosters Work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Options. . . . . . . . . . . . . . . . . . . .
PAGE 2
ENGLISH How a Cellular Booster Improves Indoor Signals Wilson cellular signal booster systems work as follows: an outdoor antenna placed on a building where some cell signal is present, (ideally on a roof or pole), receives and sends that weak signal via coax cable (like used in satellite TV installs) to a signal booster located indoors.
PAGE 3
. Connect the cable from the outside antenna to the signal booster’s “outside antenna” connector. Refer to page 6 for more information on running cable. Lightning Surge Protection is recommended for all in-building installations. Refer to pages 3 & 6. ENGLISH 4. Select a location for the inside antenna. Try to choose a position in the center of the area needing improved signal. Keep in mind that proper inside antenna to outside antenna isolation is necessary for the system to function properly.
PAGE 4
Installation Diagram ENGLISH Outside Antenna (Wide Band Directional Antenna shown) Note: A Wilson Lightning Surge Protector (859902) is recommended for all building installations. Make sure the protector is installed outside the building at point of entry connected to a suitable ground and in line between the Outside Antenna and the Signal Booster. Spacing Critical Inside Antenna Inside Antenna Preferred Method: Place the Inside Antenna in the ceiling facing down for the best coverage.
PAGE 5
ENGLISH Optional Splitter 2-way or 3-way, when using multiple inside antennas for increased coverage Optional Inside Antenna for added coverage Signal Booster Contact Wilson Electronics Customer Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com BU-GDE000096-003_050620.
PAGE 6
Selecting a Location for the Outside Antenna ENGLISH Wide Band Antenna Cell Tower The outside antenna must be mounted at a location outside of the home or building, where the strongest cell signal is present. This can be accomplished by using the Wilson Signal Meter. Alternatively, a cell phone in test mode can be used for finding the area around the building with the strongest signal.
PAGE 7
Installing Lightning Protection Warning: L ightning protection is recommended for all installations (#859902- 50 Ohm, shown below). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines. ENGLISH Install the Lightning Surge Protector (LSP) outside, in line with the coax cable from the outside antenna, near where the coax cable from the outside antenna will enter the building.
PAGE 8
ENGLISH Installing the Inside Antenna(s) Select a location for the inside antenna, preferably in the center of where the signal needs to be amplified. A minimum separation distance of 20 vertical feet and or 50 horizontal feet between the inside and outside antenna(s) may be necessary in order to achieve full booster gain and therefore maximum indoor coverage.
PAGE 9
Note: Maintain at least 6 inches of clearance from surrounding objects. Be careful when plugging the connector in so as not to damage the center pins on the connectors. Run the outside antenna cable to the signal booster and attach it to the connector labeled “Outside Antenna” on the signal booster. Run the inside antenna cable to the signal booster and attach it to the connector labeled “Inside Antenna” on the signal booster.
PAGE 10
ENGLISH Post Install Setup The Pro Series booster is designed with advanced internal programming which allows it to automatically adjust itself for a variety of conditions and still boost weak signals. After completing the amplifier installation, the LCD display and push button on the lower panel of the Pro Series booster is used to verify the final gain that the booster adjusted itself to produce after antennas have been placed.
PAGE 11
The 800 MHz Band – Cell Band 1700/2100 MHz – AWS Band OK OK The single “BAND SELECT” button is used to scroll the display through the four cellular bands in order to verify that each band is functioning properly. An asterisk (located next to the band selected) will flash if one or more bands have been turned down/off by the boosters control circuitry due to strong nearby cell site signal overload (“OVL”) and/or oscillation detection (“OSC”) from antennas being too close.
PAGE 12
Fixing Red Light Issues If the power light is red: ENGLISH 1. Make sure all connections are tight. 2. You need to increase the distance between the outside antenna and the inside antenna by moving them horizontally and/or vertically farther apart. After doing so, reset the booster by unplugging the power supply and then plugging it back in. If the light is green after separating the antennas, you have eliminated the problem. 3.
PAGE 13
Warnings and Recommendations WARNING: To uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas. WARNING: Use only the power supply provided in this package. Use of a non-Wilson Electronics product may damage your equipment. WARNING: The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 150 degrees Fahrenheit).
PAGE 14
ENGLISH ______ Antenna Kit Options The following accessories are certified by the FCC to be used with the Pro 70 Plus. This radio transmitter 4726A-460062 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
PAGE 15
ENGLISH 30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 3-Year Warranty Wilson Electronics Signal Boosters are warranted for three (3) years against defects in workmanship and/or materials.
PAGE 16
Signal Booster Specifications Pro 70 Plus™ Model Number 460062 FCC ID PWO460062 IC ID 4726A-460062 Connectors F-Female Antenna Impedance 75 Ohms Frequency 698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Passband Gain (nominal) 20 dB Bandwidth (MHz) Typical Maximum Power output for single cell phone (Uplink) dBm Power output for single cell phone (Downlink) dBm Power output for multiple received channels (Uplink) dBm No. Tones 700MHz Band12/17 64.