Specifications

1
Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660
Or email: [e-mail] Hours: 7am to 6 pm MST.
2
Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660
Or email: [e-mail] Hours: 7am to 6 pm MST.
Installation Instructions for the Following Wilson Electronics Signal Boosters:
Mobile Wireless Dual-Band Smart Technology ™ Signal Booster
Model # 271201, Part # 801201, 801212, 801215
FCC ID: PWO271201SA IC: 4726A-271201SA
Mobile Wireless Dual-Band Smart Technology ™ Signal Booster
Model # 271701, Part # 801701, 801501, 801601, 801712
NOT FOR SALE IN USA / CANADA
Wireless
Signal Booster
DC plug-in
power supply
(301127)
Low-Profile
Antenna
(301104)
NMO
Mount
Dual-Band
(301103)
Magnet Mount
Dual-Band
(301101)
Trucker
Mount
Tri-Band
(301113)
Mini
Magnet
Dual-Band
(301130)
Marine
Antenna
Dual-Band
How it Works
Your new Wilson Signal Booster has been carefully engineered to significantly improve the
performance of your cell phone and cellular data card in mobile applications. Together with
an Outside Antenna, the Signal Booster’s state-of-the-art technology is designed to increase
your signal more than 20 times, reduces dropped calls and increase data communication
rates needed for 3G technologies.
The Outside Antenna will collect the cell tower signal and send it through the cable to the
Signal Booster. The signal is then boosted and sent to the Inside Antenna. Your cellular
device then communicates with the improved signal. When the cellular device transmits, the
signal goes through the Inside Antenna, is boosted by the Signal Booster and broadcasted to
the cell tower through the Outside Antenna.
Optional Antennas
Before Getting Started
This guide will help you properly install your Wilson Electronics Dual-Band Mobile Wireless
Signal Booster. It is important to read through all of the installation steps for your
particular application prior to installing any equipment. Read through the instructions,
visualize where all the equipment will need to be installed and do a soft installation before
mounting any equipment. Contact Wilson Electronics Technical Support Team with any
questions at 866-294-1660.
Warning: In a
wireless installation,
do not plug the Signal
Booster directly into
the cell phone and/
or data card using
an antenna adapter.
It may damage the
Signal Booster, cell
phone and/or data
card
.
!
!
!
!
Quick Installation Overview
Installing the Outside Antenna
To receive the best cell signal, select a location in the center of the vehicle’s roof 12 inches
away from any other antennas or windows. If the vehicle has a sunroof, it is important to
separate the Inside and Outside Antennas by at least five feet. This prevents the Signal
Booster from overloading or oscillating. As shown above. Follow the specific antenna
installation instructions included with the Outside Antenna.
Magnet - Mount
Antenna Shown
Part #301103
Carefully
Pull Down
Door Seal
Run Cable
Under Seal
Tuck Cable
Under Seal
Tuck Cable
Tuck Cable
Separation of the Inside and Outside Antennas is
very important. The metal roof of the vehicle acts as a
barrier and helps shield the two antennas from each
other, preventing oscillation (feedback).
The Outside Antenna must be installed vertically.
Signal performance will be degraded if the antenna is
not vertical.
The antenna cable may run through the door to the
Signal Booster.
For a more professional looking installation, run the
antenna cable under the door seal. The antenna cable
is small enough to easily tuck under the door seal or
plastic molding. Carefully pull down the door seal. Run
the cable through the seal and push the seal back into
place. This prevents constant wear and tear on the
cable as the door opens and closes.
Warning: Do not plug
in the DC power supply
until the Outside and
Inside Antenna cables
are attached to the
Signal Booster.
Warning: The Outside Antenna must have a
separation of at least 20 inches from all persons
during normal operation.
Warning: Do not use any type of glass-mount
antenna with this Signal Booster. The Outside
and Inside Antennas must be shielded from each
other to prevent oscillation (feedback).
(Included with
some kits)
(Included with
some kits)
Wilson Electronics manufactures a wide variety of antennas to help you customize your
Signal Booster for your specific application. Several authorized antennas are shown above.
See your dealer or visit www.WilsonElectronics.com.
(Included with
some kits)
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Inside this Package
Installation Diagram
Outside
Antenna
Inside
Antenna
Distance between antennas
through a sunroof must be 5
feet or more.
DC Power
Supply
Signal
Booster
Cell Phone
PDA
Notebook
Appearance of device and accessories may vary.