In-Line or 75 Ohm In-Line 17dB Adjustable Gain 800/1900 MHz Smart Technology Signal Booster ™ Contents: Quick Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Understanding the Signal Booster Lights . . . . . . . . . . . . . . . Warnings and Recommendations. . . . . . . . . . . . . . . . . . . . .
Installation Instructions for: In-Line or 75 Ohm In-Line 17dB Adjustable Gain 800/1900 MHz Smart Technology ™ Signal Booster Model # 276215 FCC ID: PWO276215 IC: 4726A-276215 The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. How it Works The In-Line Signal Booster is designed to provide an additional 17dB gain to compensate for signal loss due to a long cable run or the use of taps or splitters.
Quick Install Overview Refer to Installation Diagrams on page 3 & 4. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660. 1. Install In-Building Signal Booster (such as the AG Pro 75™ sold separately). Use the installation guide for the model you purchased to install. 2. Select a location to install the In-Line that is away from excessive heat, direct sunlight, moisture and has proper ventilation. Do not place the In-Line in an air-tight enclosure. 3.
Before Getting Started This guide will help you properly install your Wilson Electronics Signal Booster. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. Contact Wilson Electronics Technical Support with any questions at: 866-294-1660.
Figure 2 Figure 3 One In-Line & Two Inside Antennas Two In-Lines & Two Inside Antennas Outside Antenna Outside Antenna Lightning Surge Protector Lightning Surge Protector 800 Signal Booster 1900 SMART TECHNOLOGY 800 Surge Protector Power Strip 62 37 32 42 47 37 62 Signal Booster 32 42 800 MHz 47 52 57 37 32 42 1900 MHz 52 57 1900 SMART TECHNOLOGY Signal Booster 32 800 MHz 52 57 37 42 1900 MHz 47 62 62 47 52 57 In-Line 800 1900 SMART TECHNOLOGY In-Line Adjustabl
Reasons for Using an In-Line with In-Building Installations Covering multiple rooms or even floors of a building can be challenging as each is a different size and shape. Balancing the signal coverage can require multiple attenuators, cables, taps and splitters. All of these can decrease your system gain and coverage. Reasons to install an In-Line include: 1.
Installing the Wilson Electronics In-Line Select a location to install the In-Line that is away from excessive heat, direct sunlight, moisture and has proper ventilation. Do not place in an air-tight enclosure. Recommended installation locations for the In-Line are: • On a shelf • In a closet • Near a power outlet • Near the Inside Antenna • Where there is more than 5dB loss between In-Building Signal Booster and Inside Antenna Note: It is important to have adequate air ventilation.
Powering up a Wilson Electronics In-Line 1. Never point the front of a Directional Outside Antenna toward the Inside Antenna. Refer to Figures 4 & 5 on page 8. 2. Run the antenna cable from the In-Building Signal Booster “Inside Antenna” connector to the In-Line “Outside Antenna” connector and attach to both connectors. Run the Inside Antenna cable to the In-Line and attach it to the connector labeled “Inside Antenna” on the In-Line. For more information refer to pages 3 & 4. 3.
Figure 4 CORRECT INSTALLATION Point antennas away from each other Recommended placement for In-Line Inside Panel Antenna Outdoor Antenna Signal Booster Figure 5 INCORRECT INSTALLATION Never point antennas toward each other Inside Panel Antenna Not recommended placement for In-Line Outdoor Antenna Signal Booster Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Mon.- Fri. Hours: 7 am to 6 pm MST.
Understanding the In-Line Lights and Troubleshooting The In-Line is equipped with two indicator lights, one for the 800 MHz band and the other for the 1900 MHz band.
2. Red If either of the two indicator lights on the In-Line are red, this indicates that the In-Line has shut down on that frequency to prevent an oscillation (feedback). First, make sure that all the connections are tight. Then reduce the gain for that frequency in small increments by rotating the gain control, counter clockwise, waiting 5 seconds between each adjustment for the InLine to reset (it may take up to 3 minutes for the In-Line to reset).
Warnings and Recommendations Warning: The Directional Antenna must always be located so the back or side points to the Inside Antenna. Never point the front of the Outside Antenna toward the Inside Antenna – this is to prevent oscillation. Warning: Connecting the In-Building Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. Warning: Use only the power supply provided. Use of a non-Wilson Electronics product may damage your equipment.
About Wilson Electronics Wilson Electronics, LLC has been a leader in the wireless communications industry for over 40 years. The company designs and manufactures Signal Boosters, antennas and related components that significantly improve cellular phone signal reception and transmission in a wide variety of applications, mobile (vehicle, RV, marine) and in-building (home, office, machine to machine).
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 2-Year Warranty Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials.
Copyright © 2013 Wilson Electronics, LLC All rights reserved. U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318 Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Mon.- Fri. Hours: 7 am to 6 pm MST.
In-Line Specifications Part # 806215 806715 Model Number 276215 Antenna connectors N-Female Antenna impedance 50 ohm Dimensions F-Female 75 ohm 5.7 x 4.2 x 1.5 inch (14.0 x 10.8 x 3.9 cm) Weight 1.27 lbs (0.
