DT™ Cellular Signal Booster 463105 Need help? www.WilsonElectronics.com Tech Support 866-294-1660 Mon.- Fri.
! IT IS VERY IMPORTANT TO POWER YOUR SIGNAL BOOSTER USING A SURGE PROTECTED AC POWER STRIP WITH AT LEAST A 1000 JOULE RATING. FAILURE TO DO THIS WILL VOID YOUR WARRANTY IN THE EVENT OF A POWER SURGE OR LIGHTNING STRIKE. ! THE SIGNAL BOOSTER UNIT IS DESIGNED FOR USE IN AN INDOOR, TEMPERATURECONTROLLED ENVIRONMENT (LESS THAN 150 DEGREES FAHRENHEIT). IT IS NOT INTENDED FOR USE IN ATTICS OR SIMILAR LOCATIONS SUBJECT TO TEMPERATURES IN EXCESS OF 150°F.
Package Contents Accessories packaged may not exactly match the below photos due to different kit options SignalBoost DT Desktop Antenna (301213) Coax Cable (30’ 950630) Cradle Antenna Kit Cradle Antenna 20’ RG6 coax cable (311141-0620) AC Power Supply 6V / 2.5A (Not included with some models) (859912) Included Accessories Cable Connector (971129) Optional Antenna Upgrade Kit 314473-0640 Kit 991171 Includes ole Mount Panel P Antenna 40’ RG6 cable 1. Pole Mount (Packet A) 2.
Rotate in small increments Find the Strongest Cellular Signal Before you install your DT signal booster, you must determine the location of the best available cellular signal. This will affect the location of your Outside Antenna and will help you get the best performance from your DT. You can find the strongest signal outside your building, typically at the highest point available, using any of the following methods: 1.
Quick Install - Inside Window Mount Option 4. Insert the Outside Antenna into the cradle. Additional installation options on pg. 6-12 Find the Strongest Cellular Signal (See page 4 for suggested methods.) Ready to Install Inside Window Mount 1. Select a location on the inside of a window as high as possible and at least 20 feet from where the DT will be located. Note that this distance typically requires the window mount to be in a different room from where you will locate the DT and Desktop Antenna.
8. Connect the DT to a surge protected AC power strip with at least a 1000 Joule rating. If your DT is working correctly, the lights will be green. Installation Options 1. Select a location on the roof where the Outside Antenna can be mounted on a pole maintaining at least 20 feet of vertical or horizontal separation from the inside Desktop Antenna. utside Pole Mount O (Best Option) If the lights are orange or red, see the “Troubleshooting” section on page 9.
5. Connect the supplied coax cable to the antenna lead cable on the Outside Antenna. 4. Route the cable as desired to the location of the DT. If you need to connect both coax cables, use the Cable Connector provided. 6. Route the cable as desired to the location of the DT. If you need to connect both coax cables, use the Cable Connector provided. Secure the cable with ties as needed (ties not provided). Rafter Mount 1.
If possible, place the Desktop Signal Antenna directly beneath the placement of the Outside Antenna location. This creates a maximized signal zone within the room where the Desktop Antenna remains. Place the desktop signal antenna directly beneath the placement of the Outside Antenna location At least 20 feet of vertical or horizontal separation from the desktop antenna is needed 5.
3. Attach the Inside Antenna to the connector labeled “Inside Antenna.” Troubleshooting & Understanding Lights The DT includes two indicator lights, one for each band (for more information about the frequency bands used by your cell service provider visit wirelessadvisor.com.) All indicator lights will be green, orange or red. 4. Ensure the Inside Antenna is facing away from both the DT and the Outside Antenna. Green indicates the unit is powered and working properly.
c) You need to increase the distance between the Outside Antenna and the Desktop Antenna by moving them horizontally and/or vertically farther apart making sure they are not facing towards each other. Fixing Blinking Red & Orange Light Issues If one or more of the lights on Signal Booster are blinking red and orange, it indicates that the Signal Booster is experiencing extreme receiver overload and has shutoff.
Additional FAQ: What hours can I contact tech support? Technical Support can be reached from 7:00am to 6:00pm MST, by calling (866-294-1660), or by email, at tech@wilsonelectronics.com. How does weather affect the performance of my Outside Antenna? Water vapor (e.g. rain, fog, snow or other precipitation) creates an effective filter to cellular signal. In times of heavy precipitation, you may see less performance.
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _________
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _________
Signal Booster Specifications SIGNALBOOST™ DT™ Specifications Model Number 460005 Outside antenna connectors F-Female / SMA-Female Outside antenna impedance 75 / 50 Ohms Inside antenna connectors SMA Inside antenna impedance 50 Ohms Dimensions 6.5 x 4.25 x 1.75 inch (16.5 x 10.7 x 4.4 cm) Weight 0.47 lbs (0.213 kg) Frequency 824-894 MHz / 1850-1990 MHz Power output 800 MHz 1900 MHz Power output for single cell phone (uplink) dBm 24.9 22.
Safety Guidelines WARNING: T o uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas and 4 feet of separation distance from Desktop antennas. WARNING: C onnecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. WARNING: U se only the power supply provided in this package. Use of a non-Wilson Electronics product may damage your equipment.
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 2-Year Warranty Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials.
