User's Manual

ManualsBrandsWilson ManualsPower RollerWilson Power Roller 930-450

SM-79D

SPECIFICATIONS

Model no.

930-450 930-750 930-1000

Free Speed (RPM)

450 750 1000

Min. Torque (Ft-Lb)

3 3 3

Max. Torque (Ft-Lb) 18 12 10

Air Pressure (psi) 90

Air Inlet

3/8” NPT

Hose

3/8” I.D.

Air Flow @Free Speed

32 CFM

Spindle

1/2” Dia. with 2 spots

Weight

4.5 lbs.

Thomas C. Wilson, Inc.

21-11 44th Avenue, Long Island City, New York 11101

Tel: (718)729-3360 Fax: (718)361-2872 http://www.tcwilson.com

E-mail: tcwilson@tcwilson.com

SM-79D

Thomas C. Wilson, Inc.

21-11 44th Avenue, Long Island City, New York 11101

Tel: (718)729-3360 Fax: (718)361-2872 http://www.tcwilson.com

E-mail: tcwilson@tcwilson.com

TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE

USER MUST READ AND UNDERSTAND OPERATOR’S MANUAL.

Rev: A, 10/1/2007

OPERATING INSTRUCTIONS

SERVICE MANUAL

MODEL 930 TUBE ROLLER

 930-450

 930-750

 930-1000

Summary of content (8 pages)

PAGE 1
SM-79D SM-79D SPECIFICATIONS Model no. 930-450 930-750 930-1000 450 750 1000 Min. Torque (Ft-Lb) 3 3 3 Max. Torque (Ft-Lb) 18 12 10 Free Speed (RPM) Air Pressure (psi) 90 Air Inlet 3/8” NPT Hose 3/8” I.D. Air Flow @Free Speed 32 CFM Spindle 1/2” Dia. with 2 spots Weight 4.5 lbs.
PAGE 2
SM-79D SAFETY INSTRUCTIONS ! SAVE THESE INSTRUCTIONS 1. 2. Do not allow corrosive gases or foreign material to enter the unit. Moisture, oilbased contaminants, or other liquids must be filtered out. Eye protection is always required when running motor. 3. Hearing protection is recommended when in close proximity to all operating air motors. 4. Dust mask, non-skid safety shoes, hard hat, gloves and other personal safety equipment must be used.
PAGE 3
SM-79D PARTS LIST SM-79D LUBRICATION Amount of oil used will vary with tool usage but daily filling of handle oil reservoir should normally be adequate. Check that a fine mist of oil is always present in the air which passes out through exhaust deflector holes. For continuous and heavy tool usage, it is preferable to use an automatic air line lubri-cator. For this purpose, the Wilson Air Filter-Lubricator Unit (Cat. #8596 for 3/8” lines) is recommended.
PAGE 4
SM-79D MAINTENANCE & SERVICING Rotor Blades - Generally these are the only parts requiring replacement after long service. Always replace the rotor blades in a set of 4 only, whenever they are broken or cylinder edge is gouged, worn uneven or worn down 1/16". This would cause the blade edges to be 1/16" below top of its slot in rotor drum. SM-79D TROUBLE-SHOOTING PROBLEM Motor will not run. Cylinder and Rear End Plate - Replacement is required only if part is broken or rubbing surfaces are gouged.
PAGE 5
SM-79D MAINTENANCE & SERVICING Rotor Blades - Generally these are the only parts requiring replacement after long service. Always replace the rotor blades in a set of 4 only, whenever they are broken or cylinder edge is gouged, worn uneven or worn down 1/16". This would cause the blade edges to be 1/16" below top of its slot in rotor drum. SM-79D TROUBLE-SHOOTING PROBLEM Motor will not run. Cylinder and Rear End Plate - Replacement is required only if part is broken or rubbing surfaces are gouged.
PAGE 6
SM-79D PARTS LIST SM-79D LUBRICATION Amount of oil used will vary with tool usage but daily filling of handle oil reservoir should normally be adequate. Check that a fine mist of oil is always present in the air which passes out through exhaust deflector holes. For continuous and heavy tool usage, it is preferable to use an automatic air line lubri-cator. For this purpose, the Wilson Air Filter-Lubricator Unit (Cat. #8596 for 3/8” lines) is recommended.
PAGE 7
SM-79D SAFETY INSTRUCTIONS ! SAVE THESE INSTRUCTIONS 1. 2. Do not allow corrosive gases or foreign material to enter the unit. Moisture, oilbased contaminants, or other liquids must be filtered out. Eye protection is always required when running motor. 3. Hearing protection is recommended when in close proximity to all operating air motors. 4. Dust mask, non-skid safety shoes, hard hat, gloves and other personal safety equipment must be used.
PAGE 8
SM-79D SM-79D SPECIFICATIONS Model no. 930-450 930-750 930-1000 450 750 1000 Min. Torque (Ft-Lb) 3 3 3 Max. Torque (Ft-Lb) 18 12 10 Free Speed (RPM) Air Pressure (psi) 90 Air Inlet 3/8” NPT Hose 3/8” I.D. Air Flow @Free Speed 32 CFM Spindle 1/2” Dia. with 2 spots Weight 4.5 lbs.