Pressure Washer User Manual

ManualsBrandsWilson ManualsPressure WasherWAM-5520-375/500

SM-165

Thomas C. Wilson, Inc.

21-11 44th Avenue, Long Island City, New York 11101

Tel: (718)729-3360 Fax: (718)361-2872 http://www.tcwilson.com

E-mail: tcwilson@tcwilson.com

SPECIFICATIONS

MODEL WAM-5500-500

WAM-5520-500

WAM-5500-375

WAM-5520-375

VOLTAGE

115

220

115

220

FREQUENCY

50/60

HORSEPOWER

1 1

RPM

1725

1425

1725

1425

SELF FEED RATE

4.2 FT PER SECOND

(1.3 m/s)

4.2 FT PER SECOND

(1.3 m/s)

SHAFT & CASING

1/2” O.D.

(12.70 mm)

3/8” O.D.

(9.52 mm)

DIMENSION

42 in x 30 in x 16 in

(1067mm x 762mm x

406mm) *excluding gun

assembly

42 in x 30 in x 16 in

(1067mm x 762mm x

406mm) *excluding

gun assembly

WEIGHT

85 lbs (38kgs) 85 lbs (38kgs)

Item Part No. Description

• Flexible Shaft Lubricator 9675-0000

• Safety Shaft Coupling 9600-0102 includes removal tool

• Flexible Shaft & Casing 9722-0045 Shaft & Casing, 3/8in OD, 45ft

• 9724-0045 Shaft & Casing, 1/2in OD, 45ft

• Spiral Brushes 61746-x0xx (Max. Speed = 1725/min.)

• 62501-x0xx (Max. Speed = 1725/min.)

LIST OF ACCESSORIES

SM-165

Thomas C. Wilson, Inc.

21-11 44th Avenue, Long Island City, New York 11101

Tel: (718)729-3360 Fax: (718)361-2872 http://www.tcwilson.com

E-mail: tcwilson@tcwilson.com

TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE

USER MUST READ AND UNDERSTAND OPERATOR’S MANUAL.

Rev: A, 2/22/2007

WILS-MATIC

AUTO TUBE PUNCHER

OPERATING INSTRUCTIONS

SERVICE MANUAL

 WAM-5500-375/500

 WAM-5520-375/500

Summary of content (12 pages)

PAGE 1
SM-165 SM-165 SPECIFICATIONS MODEL WAM-5500-500 WAM-5520-500 WAM-5500-375 WAM-5520-375 VOLTAGE 115 220 115 220 FREQUENCY 60 50/60 60 50/60 HORSEPOWER 1 1 RPM 1725 1425 1725 1425 SELF FEED RATE 4.2 FT PER SECOND (1.3 m/s) 4.2 FT PER SECOND (1.3 m/s) SHAFT & CASING 1/2” O.D. (12.70 mm) 3/8” O.D. (9.
PAGE 2
SM-165 SAFETY INSTRUCTIONS SM-165 TROUBLE–SHOOTING PROBLEM ! WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below, may result in accident, fire and/or personal injury. SAVE THESE INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 2 KNOW YOUR POWER TOOL. Read this service manual carefully. GROUNDING INSTRUCTIONS. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.
PAGE 3
SM-165 SHAFT & CASING REPLACEMENT SM-165 ASSEMBLY In order to replace the shaft and casing follow these steps: 1. Remove the brush from the Shaft & Casing. 2. Un-screw the shaft from the “Shaft Drive Connector” 1. 2. 3. Place the drive unit on its wheels and bumper. Take the handle and slide in to the slots. Insert the quick-release pins thru the handle as shown below. 3. Reverse the Shaft & Casing until it comes back out from the feed wheel. 4.
PAGE 4
SM-165 SM-165 OPERATION 1 POWER INDICATOR FEEDER GUN CONNECTOR SHAFT EXIT GUIDE HANDLE BAR SHAFT & CASING INLET WATER INLET SHAFT DRIVE CONNECTOR 4 9
PAGE 5
8 • • • Unit is powered up Reverse Trigger The shaft connector will rotate clockwise when looking onto the unit from the handle side and it will splash water. The shaft connector will rotate • counter-clockwise when looking onto the unit from the handle side and it will splash water. • • Shaft & Casing Not Connected Unit is powered up Green Light On Will pull back the brush, until the trigger is released.
PAGE 6
SM-165 OPERATION 3 • • • • Un-coil electrical cord from inside the front cover and plug it in a properly grounded outlet. Press the reset button on the GFCI plug. Un-coil Feeder Gun Assembly and connect it to the unit using the shaft connector and electrical connector. At this point the green light will come on to show that you have power inside the unit. Install the Shaft & Casing Length Stop Unit on to the Shaft & Casing: 1. Remove Shaft Stop Nut from the New Shaft & Casing (might be already removed) 2.
PAGE 7
SM-165 OPERATION 3 • • • • Un-coil electrical cord from inside the front cover and plug it in a properly grounded outlet. Press the reset button on the GFCI plug. Un-coil Feeder Gun Assembly and connect it to the unit using the shaft connector and electrical connector. At this point the green light will come on to show that you have power inside the unit. Install the Shaft & Casing Length Stop Unit on to the Shaft & Casing: 1. Remove Shaft Stop Nut from the New Shaft & Casing (might be already removed) 2.
PAGE 8
• • • Unit is powered up Reverse Trigger The shaft connector will rotate clockwise when looking onto the unit from the handle side and it will splash water. The shaft connector will rotate • counter-clockwise when looking onto the unit from the handle side and it will splash water. • • Shaft & Casing Not Connected Unit is powered up Green Light On Will pull back the brush, until the trigger is released.
PAGE 9
SM-165 SM-165 OPERATION 1 POWER INDICATOR FEEDER GUN CONNECTOR SHAFT EXIT GUIDE HANDLE BAR SHAFT & CASING INLET WATER INLET SHAFT DRIVE CONNECTOR 4 9
PAGE 10
SM-165 SHAFT & CASING REPLACEMENT SM-165 ASSEMBLY In order to replace the shaft and casing follow these steps: 1. Remove the brush from the Shaft & Casing. 2. Un-screw the shaft from the “Shaft Drive Connector” 1. 2. 3. Place the drive unit on its wheels and bumper. Take the handle and slide in to the slots. Insert the quick-release pins thru the handle as shown below. 3. Reverse the Shaft & Casing until it comes back out from the feed wheel. 4.
PAGE 11
SM-165 SAFETY INSTRUCTIONS SM-165 TROUBLE–SHOOTING PROBLEM ! WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below, may result in accident, fire and/or personal injury. SAVE THESE INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 2 KNOW YOUR POWER TOOL. Read this service manual carefully. GROUNDING INSTRUCTIONS. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.
PAGE 12
SM-165 SM-165 SPECIFICATIONS MODEL WAM-5500-500 WAM-5520-500 WAM-5500-375 WAM-5520-375 VOLTAGE 115 220 115 220 FREQUENCY 60 50/60 60 50/60 HORSEPOWER 1 1 RPM 1725 1425 1725 1425 SELF FEED RATE 4.2 FT PER SECOND (1.3 m/s) 4.2 FT PER SECOND (1.3 m/s) SHAFT & CASING 1/2” O.D. (12.70 mm) 3/8” O.D. (9.