User Manual

Wimberley, Inc. ©2017, All Rights Reserved Rev. 170822
Arched Recess
reliably grip cylindrical
objects such as small
flashlights and branches.
Foam Jaw Inserts
Grip delicate objects without damage.
Thumbscrew Turn the thumbscrew to open or close the jaws of the clip.
Compared to typical spring-activated clips, thumbscrew activated clip jaws allow
for more finesse when holding delicate objects, as well as much higher maximum
clamping force when desired.
The Plamp Clip
Clip Body
The clip is custom designed to hold
anything from the most delicate plant stems
to heavy reflectors and diffusers. It is made of
nearly unbreakable ST Nylon
Jaw opening band
This elastomer band puts tension on the clamp’s moving
jaw so that it opens when you loosen the thumbscrew. It
is made of weather/UV resistant EPDM (the same mate-
rial that industrial rubber roofs are made of)
Special notches in the clip’s jaws grab the steel rim on reflectors and
diffusers, providing a secure, slip-free attachment (applies to typical cloth
reflectors/diffusers with steel perimeter hoop). This new feature is a drastic
improvement over other clips currently on the market.
The firm grip allows you to make precise adjustments to the angle of a reflector.
You can even hold diffusers cantilevered straight out above your subject
Important Feature
Reflector/Diffuser Notches
5 Year Warranty
– See www.tripodhead.com/warranty.cfm for complete details
PP-400 The Ground Plamp
Dimensions
(coiled
-up): (L x W x H):
12” x 6” x 1.5” in Weight: 10.2 oz
(290g)
Maximum extended length:
27 inches
Package Contents: The Plamp Ground Support (Qty 1) Ground Spike (Qty 1)
Wimberley, Inc.
Phone: 1
-434-529-8385
1750 Broadway St
Toll Free: 1
-888-665-2746 (USA & Canada)
Charlottesville, VA 22902 USA
www.tripodhead.com
[e-mail]
Wimberley, Inc. ©2016, All Rights Reserved
PP-210
Plamp Rod Extension ($19.00)
Fine control using the Plamp Rod Extension
For extra dexterity try using the Plamp Rod Extension in con-
junction with the Ground Plamp or a Plamp II connected to a
tripod leg or Plamp Stake.
Tips and Tricks
Extending the reach of your Ground Plamp
If you need more reach one option is to move the Ground Plamp closer to your subject. Another
option is to extend the length of your Plamp by adding extra links to its arm. We sell a 12” long
extension (part # PP-222). The trade-off to adding extra length to your Plamp is that it becomes
less rigid. If you have a Plamp II, you can attach it in series to gain extra reach (see below).
PP-222
12” Plamp II Extension ($8.00)
Reconnecting the ball-and-socket joints of your Plamp
If the articulating arm is bent forcefully beyond its normal range of motion, it is
possible for the segments to pop out of joint. Fixing this is simply a matter of
popping the segments back together. If you have a hard time reconnecting the
joints (we realize it takes quite a bit of force), you can warm the socket (female)
end in hot water (boiling or near-boiling). This will cause the socket to expand
and make it easier to pop the ball portion into place.
Adjusting the Ground Spike fit inside the Sheath
Time and various conditions may affect the fit between the Ground Spike and Sheath. Therefore
the spike has been designed with an adjustment screw so that a snug but not excessively tight fit can be
achieved. This adjustment can be made with a standard slotted head screwdriver. If you have multiple
Ground Spikes you can use the tip of another spike to adjust the screw.
Extending the Sheath
The Sheath can be extended by about 10 inches with the
Extension Tube. Multiple extensions may be used.
You can also use standard 3/4” Schedule 40 PVC
pipe with a standard belled end or coupling fitting.
PP-320
Extension Tube ($9.00)
Replacing a lost Ground Spike
If you lose your Ground Spike or need another
you may purchase one individually.
PP-310
Ground Spike ($10.00)
Hold Additional Items with a Plamp II
A Plamp II with spring clamp can easily be attached
to the Ground Plamp, Tripod leg or Plamp Stake for
holding additional items
PP-200
Plamp II ($43.00)
Rod Extension
Plamp II
Ground Plamp
Move desirable background or
foreground elements
into the picture.
Move distracting back-
ground or foreground
elements out of the way
PP-400 Ground Plamp
Made in USA
Made in USA