Winchester Repeating Arms 275 Winchester Avenue Morgan, UT, U. S. A. 84050-9333 winchesterguns.com Winchester is a registered trademark of Olin Corporation.
Important instructions for the Winchester® Model 70™ Bolt-Action Rifle Winchester Repeating Arms Customer Service Department (United States) 275 Winchester Avenue Morgan, Utah 84050-9333 Phone: (800) 945-5237 If you have any questions or comments regarding your new firearm, please feel free to write or call us. Use the space below to record information about your new firearm.
Important instructions for the Winchester® Model 70™ Bolt-Action Rifle Winchester Repeating Arms Customer Service Department (United States) 275 Winchester Avenue Morgan, Utah 84050-9333 Phone: (800) 945-5237 If you have any questions or comments regarding your new firearm, please feel free to write or call us. Use the space below to record information about your new firearm.
Make certain the firearm does not inadvertently contain any ammunition. Remember, merely removing the magazine does not mean the chamber is unloaded. Always keep the chamber empty and the “safety” in the on safe position unless shooting is imminent. firearm in a safer status, and no guarantee can be made that the firearm will not fire even if the “safety” is in the on safe position.
Make certain the firearm does not inadvertently contain any ammunition. Remember, merely removing the magazine does not mean the chamber is unloaded. Always keep the chamber empty and the “safety” in the on safe position unless shooting is imminent. firearm in a safer status, and no guarantee can be made that the firearm will not fire even if the “safety” is in the on safe position.
from the chamber. If the primer is indented, the defective cartridge should be disposed of in a way that cannot cause harm. If the primer is not indented, your firearm should be examined by a qualified gunsmith and the cause of the malfunction corrected before further use. Glance down the barrel to make sure that no obstructions remain in the barrel. Completely clear the barrel before loading and firing again.
from the chamber. If the primer is indented, the defective cartridge should be disposed of in a way that cannot cause harm. If the primer is not indented, your firearm should be examined by a qualified gunsmith and the cause of the malfunction corrected before further use. Glance down the barrel to make sure that no obstructions remain in the barrel. Completely clear the barrel before loading and firing again.
Winchester Repeating Arms Authorized Repair Centers or by our Service Center in Arnold, Missouri. We assume no responsibility for injuries suffered or caused by unauthorized servicing, alterations or modifications of Winchester firearms. IMPORTANT: This owner’s manual pertains to the Model 70 manufactured from 1992 to present. If you have an earlier model, please contact our Customer Service Department for an earlier owner’s manual at (800) 954-6427.
Winchester Repeating Arms Authorized Repair Centers or by our Service Center in Arnold, Missouri. We assume no responsibility for injuries suffered or caused by unauthorized servicing, alterations or modifications of Winchester firearms. IMPORTANT: This owner’s manual pertains to the Model 70 manufactured from 1992 to present. If you have an earlier model, please contact our Customer Service Department for an earlier owner’s manual at (800) 954-6427.
FIGURE 3 position: i.e., the muzzle is forward or in front; the buttstock is rearward or to the rear; the trigger is downward or underneath; the sight is upward or on top. For general parts nomenclature, refer to Figure 4 on page 9. Figure 5 on pages 10 and 11 covers the general features and benefits of the Model 70 design. Fixed Blade Ejector FIGURE 4 Cocking Indicator “Safety” Floorplate Initial Cleaning and Oiling NOTICE! PLEASE TAKE NOTE OF THE FOLLOWING INFORMATION BEFORE CLEANING YOUR FIREARM.
FIGURE 3 position: i.e., the muzzle is forward or in front; the buttstock is rearward or to the rear; the trigger is downward or underneath; the sight is upward or on top. For general parts nomenclature, refer to Figure 4 on page 9. Figure 5 on pages 10 and 11 covers the general features and benefits of the Model 70 design. Fixed Blade Ejector FIGURE 4 Cocking Indicator “Safety” Floorplate Initial Cleaning and Oiling NOTICE! PLEASE TAKE NOTE OF THE FOLLOWING INFORMATION BEFORE CLEANING YOUR FIREARM.
FIGURE 5 The Model 70 three-position “safety” (left) has been proven popular by hunters and shooters for over 50 years — it blocks the firing pin and lets you open the bolt with the “safety” on. The Model 70 offers our superb anti-bind bolt design — keeping bolt function smooth. Rifle Features Blued barrels are hammer-forged. Stainless barrels are button-rifled. Both give you the precision you’re looking for. The barrel crown is recessed to help prevent damage that can affect accuracy.
FIGURE 5 The Model 70 three-position “safety” (left) has been proven popular by hunters and shooters for over 50 years — it blocks the firing pin and lets you open the bolt with the “safety” on. The Model 70 offers our superb anti-bind bolt design — keeping bolt function smooth. Rifle Features Blued barrels are hammer-forged. Stainless barrels are button-rifled. Both give you the precision you’re looking for. The barrel crown is recessed to help prevent damage that can affect accuracy.
FIGURE 6 FIGURE 7 The firing pin cocking indicator is shown in the cocked position. FIGURE 8 The “safety” in the on safe position. FIGURE 9 The “safety” shown in the intermediate position. FIGURE 10 Never rely totally on your firearm’s “safety.” It is merely an aid to safe gun handling. Like any mechanical device the “safety” can possibly fail; it can be bumped off or inadvertently manipulated into an unsafe condition. Always keep your rifle pointed in a safe direction.
FIGURE 6 FIGURE 7 The firing pin cocking indicator is shown in the cocked position. FIGURE 8 The “safety” in the on safe position. FIGURE 9 The “safety” shown in the intermediate position. FIGURE 10 Never rely totally on your firearm’s “safety.” It is merely an aid to safe gun handling. Like any mechanical device the “safety” can possibly fail; it can be bumped off or inadvertently manipulated into an unsafe condition. Always keep your rifle pointed in a safe direction.
First Installation Of The Bolt FIGURE 12 FIGURE 11 The bolt of your rifle may have been packed separately in the carton in which your rifle is shipped. You will need to insert the bolt into the action. In addition, it is always advisable to remove the bolt before cleaning. Consequently, becoming familiar with removing and inserting the bolt assembly quickly and easily is absolutely essential. Make sure the sleeve lock is engaged in the bolt notch.
First Installation Of The Bolt FIGURE 12 FIGURE 11 The bolt of your rifle may have been packed separately in the carton in which your rifle is shipped. You will need to insert the bolt into the action. In addition, it is always advisable to remove the bolt before cleaning. Consequently, becoming familiar with removing and inserting the bolt assembly quickly and easily is absolutely essential. Make sure the sleeve lock is engaged in the bolt notch.
FIGURE 13 the magazine capacity of your Model 70. Under appropriate circumstances, at a range or other suitable shooting location, load your magazine to full capacity and confirm the number of cartridges. Remember, “total” capacity includes an additional round which can be loaded in the chamber in addition to a full magazine. FIGURE 14 2. When you are ready to fire, place a cartridge directly into the chamber. Press the cartridge down until it snaps into the magazine. 3.
FIGURE 13 the magazine capacity of your Model 70. Under appropriate circumstances, at a range or other suitable shooting location, load your magazine to full capacity and confirm the number of cartridges. Remember, “total” capacity includes an additional round which can be loaded in the chamber in addition to a full magazine. FIGURE 14 2. When you are ready to fire, place a cartridge directly into the chamber. Press the cartridge down until it snaps into the magazine. 3.
4. Press the cartridge down with your thumb until it can be pushed rearward under the lips. It may help to push the rear of the follower down a bit with the thumb of your other hand to facilitate sliding the cartridge back under the magazine body lips. 3. When ready to shoot, close the bolt to load the single cartridge from the magazine into the chamber. THE Rifle IS now READY TO FIRE BY SIMPLY MOVING THE “safety” TO THE OFF SAFE POSITION and pulling the trigger. 5.
4. Press the cartridge down with your thumb until it can be pushed rearward under the lips. It may help to push the rear of the follower down a bit with the thumb of your other hand to facilitate sliding the cartridge back under the magazine body lips. 3. When ready to shoot, close the bolt to load the single cartridge from the magazine into the chamber. THE Rifle IS now READY TO FIRE BY SIMPLY MOVING THE “safety” TO THE OFF SAFE POSITION and pulling the trigger. 5.
FIGURE 15 FIGURE 16 3. Lift bolt handle up and pull the bolt fully back to remove the cartridge from the chamber. follow these warnings could result in serious injury or death. 4. Carefully reposition the magazine follower and magazine spring back into the magazine opening. Close the hinged magazine cover and make sure it snaps into place. CAREFULLY INSPECT THE CHAMBER, barrel and magazine AFTER UNLOADING TO BE SURE ALL LIVE cartridges ARE CLEARED FROM THE firearm.
FIGURE 15 FIGURE 16 3. Lift bolt handle up and pull the bolt fully back to remove the cartridge from the chamber. follow these warnings could result in serious injury or death. 4. Carefully reposition the magazine follower and magazine spring back into the magazine opening. Close the hinged magazine cover and make sure it snaps into place. CAREFULLY INSPECT THE CHAMBER, barrel and magazine AFTER UNLOADING TO BE SURE ALL LIVE cartridges ARE CLEARED FROM THE firearm.
FIGURE 17 FIGURE 18 Remove the two action screws that secure the bottom metal. Lift the bottom metal from the stock. FIGURE 19 FIGURE 20 Lift the barrel and action from the stock. Trigger Pull Weight Adjustment Screw Overtravel Adjustment Screw Notice! Do not turn the trigger pull weight screw in too far. Doing so will limit the trigger travel, rendering the trigger inoperative, and could damage the pull weight spring.
FIGURE 17 FIGURE 18 Remove the two action screws that secure the bottom metal. Lift the bottom metal from the stock. FIGURE 19 FIGURE 20 Lift the barrel and action from the stock. Trigger Pull Weight Adjustment Screw Overtravel Adjustment Screw Notice! Do not turn the trigger pull weight screw in too far. Doing so will limit the trigger travel, rendering the trigger inoperative, and could damage the pull weight spring.
the sights set as they come from the factory (intermediate position on both elevation and windage), and then make incremental adjustments to move the rear sight blade and blade holder to position the group on your target. The procedures below are for a common style of open sights found on Model 70 rifles. To decrease the amount of overtravel, turn the adjustment screw closest to the action in a clockwise direction using a 1/16" Allen wrench.
the sights set as they come from the factory (intermediate position on both elevation and windage), and then make incremental adjustments to move the rear sight blade and blade holder to position the group on your target. The procedures below are for a common style of open sights found on Model 70 rifles. To decrease the amount of overtravel, turn the adjustment screw closest to the action in a clockwise direction using a 1/16" Allen wrench.
8. Tighten the screws snugly, but do not overtighten. bristles from breaking off, the brush should be pushed completely through the barrel before being withdrawn. Cleaning Procedures 9. Mount your scope rings and scope as outlined in the instructions supplied with your scope rings and/or scope. Always make sure you have the proper eye relief. Always make sure that the saddle crossbolts and cap bolts are fully tightened before using your firearm.
8. Tighten the screws snugly, but do not overtighten. bristles from breaking off, the brush should be pushed completely through the barrel before being withdrawn. Cleaning Procedures 9. Mount your scope rings and scope as outlined in the instructions supplied with your scope rings and/or scope. Always make sure you have the proper eye relief. Always make sure that the saddle crossbolts and cap bolts are fully tightened before using your firearm.
FIGURE 21 6. Wipe all exposed metal surfaces with a lightly oiled cloth making certain that all finger marks are removed. Finger marks provide a place where moisture can accumulate. The metal of the gun should receive a light film of oil any time the rifle has been exposed to weather or handling. FIGURE 22 Keep all ammunition away from the cleaning area. Never test the mechanical function of your rifle with live ammunition. Failure to follow these warnings could result in serious injury or death. 7.
FIGURE 21 6. Wipe all exposed metal surfaces with a lightly oiled cloth making certain that all finger marks are removed. Finger marks provide a place where moisture can accumulate. The metal of the gun should receive a light film of oil any time the rifle has been exposed to weather or handling. FIGURE 22 Keep all ammunition away from the cleaning area. Never test the mechanical function of your rifle with live ammunition. Failure to follow these warnings could result in serious injury or death. 7.
Parts, Service, Repair and Questions As the breech bolt sleeve/firing pin assembly is screwed back into the breech bolt, the cocking ramp of the firing pin must compress, then decompress several times before the assembly is fully screwed in. Place the breech bolt on a flat, hard surface, and using the breech bolt handle and the head of the bolt as a support, firmly turn the breech bolt sleeve clockwise until it snaps into position.
Parts, Service, Repair and Questions As the breech bolt sleeve/firing pin assembly is screwed back into the breech bolt, the cocking ramp of the firing pin must compress, then decompress several times before the assembly is fully screwed in. Place the breech bolt on a flat, hard surface, and using the breech bolt handle and the head of the bolt as a support, firmly turn the breech bolt sleeve clockwise until it snaps into position.
Notes 32
Notes 32
Winchester Repeating Arms 275 Winchester Avenue Morgan, UT, U. S. A. 84050-9333 winchesterguns.com Winchester is a registered trademark of Olin Corporation.