OWNER’S OPERATING & MAINTENANCE MANUAL 2570 Blood Drawing Chair 2573 Padded Blood Drawing g Chair 2571 Blood Drawing Chair 2572 Padded Blood Drawing g Chair 2574 XL Padded Blood Drawing Chair 2575 XL Padded Blood Drawing Chair 2578 Designer Blood Drawing g g Chair 2588 Power-Lift Designer g Blood Drawing Chair PLEASE DO NOT DISCARD THIS MANUAL! KEEP IT FOR FUTURE REFERENCE AND TRAINING
TABLE OF CONTENTS PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT! If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-3377 before attempting to use this product; otherwise injury may occur. Winco assumes no responsibility for damage or injury caused by improper assembly, installation, use, or maintenance of these products. Table of Contents Winco Contact Information ..............................................
WINCO CONTACT INFORMATION & WARRANTY 5516 Southwest 1st Lane Ocala, FL 34474 1-800-237-3377 / 352-854-2929 / Fax: 352-854-9544 e-mail: customerservice@wincomfg.com Visit us on the web: www.wincomfg.com Limited Warranty TERMS Winco Mfg., LLC. warrants this product to be free of manufacturer’s defects in material and workmanship, provided that the product is used according to normal operating conditions and proper maintenance intended by manufacturer.
IMPORTANT - PLEASE READ FOR PRODUCTS WITH POWERED OPTIONS Read all instructions before using this product. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS To reduce the risk of electric shock when using an electrical appliance, basic precautions should always be followed, including the following: DANGER - Always unplug this product from the electrical outlet before cleaning, maintenance or when putting on or taking off parts. WARNING: 1.
IMPORTANT - PLEASE READ GROUNDING INSTRUCTIONS: This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Tools Needed Models 2570–2575: • Multiple size wrench included (or your own 5/16, 3/8” & 7/16” or adjustable wrenches) • Phillips-head screwdriver • Scissors or box cutter • Powered tools not recommended Models 2578 & 2588: • Multiple size wrench included (or your own 7/16” or adjustable wrench) • 3/16” Hex “Allen” wrench included • “Phillips-head” screwdriver – for checking tightness of all screws after shipping • Scissors or box cutter • Powered tools not recommended.
Seat Installation WARNING 2570-2575, 2578, 2588 Failure to completely tighten the seat mounting screws COULD RESULT IN SERIOUS INJURY. FIG. 1 Models 2570 and 2571 (FIG. 1) 1. Position Chair Frame in upright position. Check tightness of all installed screws, bolts and nuts in case they loosened during shipping. 2. Align the mounting holes on the plastic Seat with the Seat Support holes. Hole spacing of Seat and Seat Supports will be narrower toward front of chair.
Arm Installation - All models 1. If the Arm Assembly has not yet been installed, insert it into the Receiving Tube on Seat Frame Assembly. (This applies to any style arm assembly) •ALWAYS make sure that the slot in the Arm Assembly faces the Knob installed on the receiving tube. (FIG. 1) 2. Then adjust the arm to the desired height and tighten the knob. Screw the Knob into the Slot. This will “capture” the arm and keep it from being able to be pulled out of the frame accidentally.
Cabinet Assembly Models 2570, 2572, & 2574 1. Remove the drawer from the cabinet. 2. Attach the Welded Cabinet Support to bottom of Cabinet by installing (4) 2” screws through (4) holes in the Welded Cabinet Support. Install washers and locknuts on the screws inside the cabinet. (FIG. 1). 3. Use the supplied wrench to hold nuts inside of cabinet & tighten screws with a Phillips scredriver. 4.
Models 2578 Seat Height Set-up and/or Adjustment The seat height of your 2578 Designer Blood Drawing Chair can be adjusted during setup. CAUTION: The Seat Assembly is VERY HEAVY. To adjust the height; the chair must be supported by someone that can LIFT OVER 50 LBS. 1. Use two people; Use the included 3/16” Hex (Allen) wrench and the included “multi-size” wrench to remove the nut, lockwasher & shoulder bolt from the square post on the Base Assembly. 2. Align the Seat Bracket over Seat Post. 3.
“PR” & “P2” - Optional Pivot Arm (see models listed below) **If ordered with “L” shaped arm follow arm assembly instructions on page 8** Models 2570-2571-2572-2573-2574-2575 PR and 2571-2573-2575 P2 Your Pivot Arm assembly may be configured in one of two (2) directions: • Pivot point located near the back of chair – This will provide arm support that is straight or at a slight angle to the side of the patient (standard position).
5516 Southwest 1st Lane Ocala, FL 34474 1-800-237-3377 / 352-854-2929 / Fax: 352-854-9544 e-mail: customerservice@wincomfg.com Visit us on the web: www.wincomfg.