BA83 LCD TFT 15" (38.
We would like to know your opinion on this publication. Please send us a copy of this page if you have any constructive criticism. We would like to thank you in advance for your comments. With kind regards. Your Opinion: Wincor Nixdorf International GmbH Dokumentation RD HWD01 Rohrdamm 7 D-13629 Berlin E-Mail: retail.documentation@wincor-nixdorf.com Order No.
BA83 Flat Panel Display User Guide Edition September 2011
All brand and product names mentioned in this document are trademarks of their respective owners. Copyright© Wincor Nixdorf International GmbH, 2011 The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability; technical modifications possible.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . 1 From Point-of-Sale To Point-of-Service . . . . . . . . . . . . . . . . . . 1 Advantages At a Glance . . . . . . . . . . . . . . . . . . . . . . . . 2 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The Flat Panel Display BA83 . . . . . . . . . . . . . . . 3 General . . . . . . . . . . . Operator Panel Module . . . USB Interface . . . . . . On Screen Display (OSD) LED . . . . . . . . . . . On/Off Button . . .
Inserting Key Caps. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Swipe Card Reader In a Keyboard (optional) . . . . . . . . . . . . . . 15 Waiter Lock (optional) . . . . . . . . . . . . . . . . . . 16 Installing and Securing . . . . . . . . . . . . . . . . . 17 Unpacking And Checking the Delivery Unit Installing the Base . . . . . . . . . . . . . Table Mounting . . . . . . . . . . . . . . Mounting the Tube Adapter . . . . . . . . Connection Bezel . . . . . . . . . . . . . Connecting the BA83 .
Display Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Current Consumption Of the Screen Module . . . . . . . . . . . . . . 66 Programming the Keyboard And MSR . . . . . . . . . 67 Interfaces . . . Files . . . . . . Modus . . . . . Creating Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FROM POINT-OF-SALE TO POINT-OF-SERVICE Introduction From Point-of-Sale To Point-of-Service With the BA83 you are using a ergonomical and customer-friendly cashier’s workplace. The BA83 is connected to the system via a VGA or DVI interface. Power is supplied via a PoweredUSB interface or an external power supply unit. The Touch screen as well as the USB Hub are contolled via a USB cable or via a PoweredUSB cable.
ABOUT THIS MANUAL Advantages At a Glance n Low footprint n Autoscaling of the screen n Flickerfree and free from radiation n Very good contrast ratio, adjustable loudness, sharpness, width, phase, colour temperature and brightness via OSD menu n LCD TFT-Technology n Digital Interface n Simple installation via plug and play feature n Mounting VESA 75 & 100 standard n Integrated loudspeaker n USB interfaces for external devices About This Manual This manual informs you about everything you might need to kn
GENERAL The Flat Panel Display BA83 General The TFT LCD flat panel display is an XGA-compatible 15-inch flat panel display which is absolutely flickerfree and free from radiation. It is designed for a resolution of max. 1024 x 768 pixel.
OPERATOR PANEL MODULE USB Interface A ‘Plug and Play’ interface (Type A) for connecting peripherals during operation, e.g. USB sticks or a keyboard. On Screen Display (OSD) Menu Via the menu you can set the loudness, brightness, contrast and colour. Scrolling The arrows serve for scrolling forwards or backwards in the menu items.
SECURITY Security The operator panel module can be mounted horizontally turned thus to handicap the access. Slightly press the module inwards at the left and right hand side (1). Remove the module of the recesses and carefully move it off downwards (2). Carefully turn the device through 1800 (3). Reinsert the module into the recesses (4). Mind not to jam the cables.
INTEGRATED LOUDSPEAKERS Integrated Loudspeakers The two integrated loudspeakers are located at the bottom side of the screen (see arrows).
CAPAZITIVER TOUCH SCREEN Capacitive Touch Screen General The TFT Touch Screen works according to the principle of a change in analog capacitance. It has a glass screen with a transparent, thin-film overlay on the surface. This is fully sealed and protected by a further layer of clear glass. Electrodes on the edges of the screen provide an uniform low-voltage field. As soon as you touch the screen with your finger the contact point is “recognized” by the change in capacitance.
CLEANING INSTRUCTIONS Cleaning Instructions Always turn off the system before cleaning. The glass surface of your Touch Screen should be cleaned with a mild, abrasive free, commercially available glass cleaning product. All pH neutral materials (pH 6 to 8) are good for cleaning. Cleaners with pH values 9 to 10 are not recommended. Cleaning with water and isopropyl alcohol is possible as well. Do not use solvents containing acetic acid. Use a soft, fine-meshed cloth to clean the surface.
GENERAL Infrared Touch Screen General The infrared (IR) technology is based on the interruption of a grid of IR light beams before the surface of a screen. The touch frame contains a row of infrared light emitting diodes (LEDs) and photo transistors, each mounted on two opposite sides to create a grid of invisible infrared light.
CLEANING INSTRUCTIONS Breaking through the grid has the same effect as clicking the left mouse button. Therefore, touching the glass is not necessary. To avoid malfunctions: Do not fix labels or stickers on the frame and do not put pencils or the like on the inner frame. Cleaning Instructions Always turn off the system before cleaning. The glass surface of your Touch Screen should be cleaned with a mild, abrasive free, commercially available glass cleaning product.
HOW TO OPERATE Swipe Card Reader (optional) The swipe card reader (MSR Module), that is available as an option, can read three ISO tracks simultaneously in a single swipe. The MSR module is fitted on the right-hand or left-hand side of the keyboard module or screen module. How To Operate Run the swipe card through the slit of the swipe card reader from top to bottom in a quick and steady movement. Make sure that the magnetic strip is to the right.
CLEANING INSTRUCTIONS Keyboard (Option) The keyboard is connected directly to the display via a USB interface. It is fitted to the right-hand side of the screen. The keyboard is available with or without a swipe card reader. Cleaning Instructions The keyboard should be cleaned with a germicide from time to time. Before cleaning in between the keys on the keyboard with a brush, loosen and remove the key caps using the key removing device. Do not allow dust to get in through the open keyboard mechanics.
EXCHANGING THE KEYS Exchanging the Keys You can remove each of the key caps using the key removal device enclosed, pulling the key upwards. Place the key removal device on the selected key until you hear a click. Now remove this key from the keyboard by pulling it upwards. If the key that has been removed is already labelled you can change the lettering as follows: By using a thin object (e.g. paper-clip etc.), press upwards against the plastic cover through the opening on the underside of the key.
INSERTING KEY CAPS Inserting Key Labels Below you will find instructions on how to insert the key labels: Each key should be labelled individually. You can use the empty labels delivered with the system to do so. Key cover with mat side up Label for keys Place the label on the key cap. Key cap Insert the key cover with the mat side upwards until it clicks into place in the key cap. Inserting Key Caps Insert the key cap in the keyboard and press it firmly into place.
SWIPE CARD READER IN A KEYBOARD (OPTIONAL) When inserting double keys, please ensure that the actuating cylinder is on the left (horizontally inserted key) resp. on top (vertically insertion). Mind to insert quadruple key caps with the cylinder on the upper left. actuating cylinder Swipe Card Reader In a Keyboard (optional) The keyboard is available with or without a Swipe Card Reader. This module corresponds to the module "Swipe Card Reader". For technical data see the accordant chapter on page 52.
WAITER LOCK (OPTIONAL) Waiter Lock (optional) Each transaction is correctly as signed to the personell by using the magnetic key. The magnetic keys are available in 10 different colors. The magnet keys are waterproof, shatterproof and by the 16-digit key number also safe for clear identification. The operation of the sys tem is very simple, the key is placed onto the magnetic probe (see figure). The key is held magnetically to the probe and transmits the data by an electrical USB interface.
UNPACKING AND CHECKING THE DELIVERY UNIT Installing and Securing Unpacking And Checking the Delivery Unit Unpack the parts and check to see whether the delivery matches the information on the delivery note. The delivery comprises the respective screen module. Data cables, necessary for operation, can be ordered separately. If damage has occurred during shipping or if the package contents do not match the delivery note, immediately inform your Wincor Nixdorf sales outlet.
TABLE MOUNTING Loosen the four screws on the screen for approx. 2 mm. Put the screen element on to the base. USB P-USB 12V DVI-I RMT Wincor Nixdorf BA8X/ cTouch 017500 000000 5V/ 12V 0.7A/ 0.7A I.T.E. IC 78+E146247 0199900107 WN Made in China Tighten monitor and base with the four Phillips screws, loosened before. When demounting the base always make sure that all cables are disconnected.
MOUNTING THE TUBE ADAPTER Table Mounting Underneath the cable cover there are two holes in the BA83 stand (see arrows) with a diameter of 5.5 mm. The holes can be used to fix the stand on the footprint with appropriated screws. We recommend using screws with a diameter of 4.0 to 5.0 mm. Note that the screw type is suitable for the footprint material. Useful applications may be: n Determine a certain position e.g. above a cable aperture in the table. n Secure the display stand against “theft by passing”.
MOUNTING THE TUBE ADAPTER Mounting the Tube Adapter Take the tube adapter out of the cardboard box and lay it next to the display. For the mounting you need a Phillips head screwdriver for fixing and releasing the screws. Pull the cover downwards (see pages 16, 17). Loosen four screws at the rear side of the BA83 and put them aside.
MOUNTING THE TUBE ADAPTER After cabling the display put on the optinal available cover. Put the display with the adapter on the preinstalled tube (1) and fix it with the screw (2).
CONNECTING THE BA83 Connection Bezel The following sockets are located under the bezel of the screen: USB- A PoweredUSB (12) DC Power Jack/12 V DVI- I RJ10/RMT USB- A For external peripherals, can be used for MSR PoweredUSB Data transfer and/or current supply for the screen via system e.g.
DUAL DISPLAY HOLDER When laying this cable please mind to slightly clamp it (with a loop) into the strain relief. Lay the cable into the guidance inside the base. Lay a USB-A cable loosely-fitting into the strain relief. When passing the cables please mind the following maximal cable diameters (in mm). 8,5 3,5 3,5 7,5 7,5 Fix cable with the strain relief (see arrows). Reinsert the cable cover and the bezel.
MOUNTING POSITIONS Dual Display Holder The Dual Display Holder offers the possibility to mount a customer display to the rearside of a cashier display. This option needs little space so that you can use your workplace in an optimized way. The holder is screwed to a main display via a hanging (VESA), while the main display is placed on a foot. The second display (here the BA80) is to be hinged and fixed with screws (see installation manual BA8x, Dual Display Holder).
MOUNTING PERIPHERALS Mounting Positions There are three mounting positions.Two (at the left and right hand side) can be used to install Magnetic Card Reader; a keyboard may be installed at the right hand side. The third position is located above the screen. Other units (e.g. a camera, not avaible at that time) can be installed above the screen.
MOUNTING PERIPHERALS Ergonomic Terminal Workplace Please observe the following when setting up your terminal workplace: Avoid direct glaring and reflective glaring. Use the screen only in a controlled luminance surounding. Install the device with a viewing direction that is parallel to the windows. Avoid reflective glaring caused by electric light sources.
MOUNTING PERIPHERALS Mounting Peripherals Unpack the parts and check whether the delivery matches the details of the delivery note. Keyboard And Swipe Card Reader The delivery contains the keyboard with Swipe Card Reader (SCR), the connected cable, the pre-installed holder (BA83), the holder of the BA82, two screws and a set of keys including a key remover.
MOUNTING PERIPHERALS Loosen the two screws (see arrows) and remove the bracket. Turn the screen around and remove the bezel (see page 17). Loosen the screws beneath the cover. Lift the screen out of the holder to the top. Lay the screen on an appropiate base.
MOUNTING PERIPHERALS Loosen the snap arms of the loudspeaker's bezel (see arrows). Flap the bezel downwards. Carefully press out the blind screen from inside.
MOUNTING PERIPHERALS Push the bracket into the opening of the housing, so that the holes are lying upon each other. Tighten with two (delivered) screws. You must always discharge yourself (e. g. by touching a grounded object) before mounting. Take care to pull the connector off the keyboard. Pass the keyboard cable through the housing into the cable guidance and connect it.
MOUNTING PERIPHERALS Push keyboard beneath the bracket. Take care that the upper parts of the hooks (see arrows) are above the plate! Mind that the screws match with the keyholes. Keyhole Screw Tighten the keyboard. If you are going to use the USB interface at the backside of the BA83 then run the cable loosely through the strain relief as shown below. Put the cable loop into the housing.
MAGNETIC SWIPE CARD READER If a device has a second Hub, you can connect the keyboard at the next free port on the Hub. To do so, release the cable's loop and run the cable through the strain relief. Strain relief USB interfaces (HUB) Insert the cover of the keyboard as shown below. The metal bar is corresponding to the gap (1) and push it to the housing until it is engaged (2). Flap the loudspeaker's bezel upwards and snap it into place. Mount the monitor's stand.
MAGNETIC SWIPE CARD READER Magnetic Swipe Card Reader The Magnetic Swipe Card Reader can be mounted on either the right or the left side of the screen. The delivery contains the Swipe Card Reader (SCR), the connected cable, the pre-installed holder (BA83), a holder (BA82) and two screws. SCR, cable and holder BA83 holder BA82 Do not release the cable loop. Turn the Swipe Card Reader and push the cover sidewards (see arrow).
MAGNETIC SWIPE CARD READER Mounting On the Right Side Loosen the Torx screws and remove the bracket. Turn the screen and remove the cover (see page 17). Loosen and remove the screws beneath the cover. Lift the screen out of the holder to the top.
MAGNETIC SWIPE CARD READER Loosen the snap arms of the loudspeaker's bezel (see arrows). Flap the blind bezel downwards. Carefully press out the blind screen from inside.
MAGNETIC SWIPE CARD READER Push the bracket of the Reader into the opening of the housing, so that the holes are lying upon each other. Then tighten it. You must always discharge yourself (e. g. by touching a grounded object) before mounting. Take care to pull the connector off the swipe card reader.
MAGNETIC SWIPE CARD READER Pass the swipe card reader cable through the housing into the cable guidance and connect it. Push the reader beneath the bracket so that the screws fit into the keyhole and the holder lays under the clamps. Clamp Screw Keyhole Clamp Tighten the screws.
MAGNETIC SWIPE CARD READER Pass the cable loosely through the cable guidance and connect it to the USB interface. Put the cable loop into the housing (see big arrow). OSD Cable connection Cable connection for Swipe Card Module If a device has a second Hub, you can connect the swipe card reader at the next free port on the Hub. To do so, release the cable's loop and run the cable through the strain relief.
MAGNETIC SWIPE CARD READER Attach the cover of the Swipe Card Reader (1) and push it to the monitor until it engages (2). Flap the loudspeaker's bezel upwards and snap it into place. Mount the monitor's stand. Mounting On the Left Side Proceed as described above ("Mounting on the right side"). Disconnect the cable to connect it to the USB interface at the rearside of the monitor. Push the bracket of the Reader into the opening of the housing, so that the holes are lying upon each other.
MAGNETIC SWIPE CARD READER Clamp Push the reader beneath the bracket, so that the screws fit into the keyhole and the holder lays under the clamps. Tighten the screws. Pass the cable through the cable guidance and connect it to the USB interface. If a HUB is available you should use one of it's USB interfaces. Do not release the cable loop. Clamp Attach the cover of the swipe card reader and push it to the monitor until it engages (see page 39).
WAITER LOCK Waiter Lock The waiter lock can be mounted on either the right or the left side of the screen. The delivery contains the waiter lock (1), the connected cable (2), a pre-installed BA83 holder (3); a BA82 holder (4) and two screws (5). Do not release the cable loop. Turn the waiter lock and push the cover sidewards (see arrow).
WAITER LOCK Mounting on the right Side Loosen the screws of the retain plate. Move the retain plate out of the guide in direction of the arrows and lift it up.
WAITER LOCK Pull the electronic element out of the housing. You must always discharge yourself (e. g. by touching a grounded object) before mounting. Loosen the screws and pull the plug.
WAITER LOCK Turn the screen and remove the cover (see page 17). Loosen the 4 mounting screws about 3 mm beneath the cover . Lift up the screen out of the holder to the top. Lay the screen on an appropiate base. Unlock the latch of the loudspeaker's bezel (see arrows). Flap the bezel downwards.
WAITER LOCK Carefully press out the blind screen from inside.
WAITER LOCK Pass the cable through the cable guidance and connect it to the USB interface. Put the cable loop into the housing (see big arrow). OSD Cable connection Cable connection for Swipe Card Module If you are going to use the USB interface at the backside of the BA83 then connect the waiter lock to any free interface at the HUB. To do so, release the cable's loop and run the cable through the strain relief (see page 38). Pass the waiter lock cable through the housing.
WAITER LOCK Plug the jack to the connection of the waiter lock. Screw electronic and element together and clamp it into the housing until it is engaged. Screw the retain plate at the BA83.
WAITER LOCK Use the left borehole of the two pairs of boreholes to install the retain plate. Put the cable of the waiter lock into the housing. Slip the waiter lock on the retain plate and push it backwards. Make sure that the cable is not crimped. Screw the waiter lock to the retain plate.
WAITER LOCK Put the housing of the waiter lock on the retain plate and push it until it is engaged. Control the cabling. Flap the loudspeaker's bezel upwards and snap it into place. Mount the monitor's stand.
WAITER LOCK Mounting on the left Side Proceed as described above ("Mounting on the right side", page 44ff). Fasten the retain plate of the waiter lock on the opening of the housing rotated 180°. Use the right borehole of the two pairs of boreholes to install the retain plate. Put the cable of the waiter lock into the housing. Slip the waiter lock on the retain plate and push it backwards. Make sure that the cable is not crimped. Screw the waiter lock to the retain plate.
ON SCREEN DISPLAY (OSD) On Screen Display (OSD) A set of 4 buttons is located at the operator panel module. Menu/ select left right scrolling Power Pressing the menu button will activate the OSD. Depending on the selected function, a sub- menu option will be available for a selection on the same screen. There are two ways to exit the OSD menu: n via exit or n wait for the OSD to time-out (saves changes and exit). The adjustments will be saved in each way.
ON SCREEN DISPLAY (OSD) Input Source The Input Source indicates the active video channel BA83 1024x768 60Hz Input Source Analog Input (VGA) Digital Input (DVI) Exit sub menu 52
ON SCREEN DISPLAY (OSD) Display Setting BA83 1024x768 60Hz Display Setting Brightness Sub menu Contrast Sub menu If the contrast is set too high, bright surfaces can no longer be distinguished from very bright surfaces. If the contrast ist set too low, the maximum brightness will not be achieved.
ON SCREEN DISPLAY (OSD) Colour Setting The colour setting is only adjustable in the normal running temperature. The display must run at least 20 minutes. BA83 1024x768 60Hz Auto Color Auto Colour (auto colour adjustment at VGA mode only) sRGB settings Standard RGB settings Colour temperature Choose the colour temperature in the sub menus, measured in K (Kelvin). Choose "factory settings" in the Tools menu to set the original settings again.
ON SCREEN DISPLAY (OSD) Sub menu colour temperature RGB Setting manual setting There are 5 basic settings: 4200K 5000K 6500K (setting, for example , for image processing or playing DVD) 7500K 9300K (setting for CAD/ CAM applications) Exit sub menu Exit menu 55
ON SCREEN DISPLAY (OSD) Image Setting (VGA- Mode) BA83 1024x768 60Hz Image Setting Auto scaling (auto adjustment) Should the image setting be faulty during the initial operation this function will adjust the image if necessary you operate "Auto colour" in addition. Width Sub menu Phase Regulates the sampling rate for transfer the analog amplifier into digital signals. This setting allows to produce a sharp image.
ON SCREEN DISPLAY (OSD) Horizontal position Sub menu Vertical position Sub menu Exit sub menu 57
ON SCREEN DISPLAY (OSD) Tools Menu BA83 1024x768 60Hz To o l s M e n u Factory setting No reset of Image Setting (Screen width, phase, horizontal/vertical position) After reset to factory setting at VGA mode: it is absolutely necessary to operate "Auto colour" (see page 54), you can operate "Auto scaling" in addition (see page 56). Sharpness The setting upgrades the contour of a blurred text by a lower solution.
ON SCREEN DISPLAY (OSD) Information about the firmware version Exit sub menu Volume Setting BA83 1024x768 60Hz Vo l u m e S e t t i n g s Volume Sub menu Exit sub menu
ON SCREEN DISPLAY (OSD) EXIT OSD BA83 1024x768 60Hz Exit OSD 60
TECHNICAL DATA BA83 Technical Data BA83 Diagonal Screen size 15" (38.1 cm) Active screen size (horizontal x vertical) 304 mm x 228 mm Cable length up to 3 m Dimensions Display Housing 368 x 300 x 90 (WxHxD, mm) w/o base 4.5 kg with base 6.7 kg Dimensions Weight Climate class IEC 721 3/3 Class 3K3 Operating temperature +5°C - +40° C Humidity 5% - 85% Absolute humidity 1g/m³ - 25g/m³ Condensation is not permitted Horizontal (KHz) typ. 48.3 Vertical (Hz) typ.
TECHNICAL DATA BA83 Dimensions (mm) 351 299 314 368 5° 280 ° 246 351 65 206 93 62 294
TECHNICAL DATA BA83 Capacitive Touch Screen Horizontal 16k Vertical 16k Resolutions LCD Technology Analog capacitive Surface anti-reflection (capacitive) Brightness typ. 200 cd/m² Data transfer USB Infrared Touch Screen Horizontal 4096 pixel Vertical 4096 pixel Resolutions LCD Technology infrared touch Surface anti-reflection Brightness typ. 220 cd/m² Data transfer USB Keyboard Protocol HID 1.1 (Human Interface Device) Power supply USB Bus powered Connection USB- A (USB 2.
TECHNICAL DATA BA83 Width 140 mm Depth 40 mm Weight approx. 800 g MSR Inside Keyboard Number of tracks up to 3 Coding of swipe cards according to ISO 7811-2 Reading speed 10 to 140 cm/sec. MSR Module 64 Protocol HID 1.1 (Human Interface Device) Power supply USB Bus powered Connection USB- A (USB 2.0 compliant) Number of tracks up to 3 Coding of swipe cards according to ISO 7811-2 Reading speed 10 to 140 cm/sec.
TECHNICAL DATA BA83 Screen Driver Installation/ Installation Tool A driver is available for the following operating systems: n Windows: Windows XP, WEPOS n Linux: WNLPOS. You can find detailed information about the driver installation in the "Read me" file on the internet. http://www.wincor-nixdorf.com/internet/site_EN/EN/Support/Downloads/POS LotterySystems/Driver/Display/Display_node.html Display Coding The second position on the type label (B) is important for the driver installation.
TECHNICAL DATA BA83 B= 2 Wincor Nixdorf Ba83/ irTouch 017500 000000 12 V 2.6A A.2.C US Listed I.T.E. IC 78 + E146247 Made in CHINA S/N 56DJ000171 You do not need driver of basic functions for infrared Touch, because the touch has an USB HID device. An installation tool "irTouch Control Panel" is available, if you need more functionality. Calibrate the Touch Screen when you connected it for the first time. Current Consumption Of the Screen Module The maximum power input of the BA83 is 2.6 A (12VDc).
INTERFACES Programming the Keyboard And MSR Utility KbUtiUSB is used for Programmable Wincor Nixdorf Keyboards with a USB HID interface. Programmability of Keyboard and Magnetic Swipe Card Reader (MSR) allows to adapt them to special needs.
FILES Files On the Wincor Nixdorf Internet site you can find the KbUtiUSB package. This package is written in Java and therefore there is a version for Windows and for WNLPOS (Wincor Nixdorf’s Linux Distribution). KbUtiUSB requires at least a Java Runtime Version 1.4.2_06.
MODUS Modus Keyboard and MSR may have two different states: “Default” This is the default state of keyboard and MSR, codes are assigned by firmware “Programmed” In this case a table has been sent to keyboard or even MSR Creating Tables Tables can be created and sent / received using KbUtiUSB under Windows or WNLPOS.
KEYBOARD CODES (STANDARD) Software Interfaces Keyboard Codes (Standard) (F1) 3B 3B 00 (F9) 43 43 00 (ESC) 01 01 1B (BS) 0E 0E 08 (F2) 3C 3C 00 (F10) 44 44 00 (s) 1F 1F 73 (u) 16 16 75 (F3) 3D (Clft) E0,4B 4B E0 (Crgt) E0,4D (Y) 15 15 79 (F4) 3E 3E 00 (PgUp) C E0,49 49 E0 (PgDn) E0,51 51 E0 (n) 31 31 6E (F5) 3F 3F 00 7 47 47 37 8 48 48 38 9 49 49 39 (F6) 40 40 00 4 4B 4B 34 5 4C 4C 35 6 4D 4D 36 (F7) 41 41 00 1 4F 4F 31 2 50 50 32 3 51 51 33 (F8) 42 42 00 0 52 52 30 .
GENERAL AUTHORIZATION Manufacturer’s Declaration And Approval General Authorization This device complies with the requirements of the directive 2004/108/EC with regard to “Electromagnetic Compatibility” and 2006/95/EC "Low Voltage Directive". Therefore, you will find the CE mark on the device or packaging. FCC-Class A Declaration This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
USER INFORMATION User Information Repair work on the devices should only be carried out by authorized and specially trained personnel. Improper repairs will lead to the loss of any guarantee and liability claims. Extension boards with electrostatically endangered components can be identified with this label. Safety Information This device conforms to the corresponding safety regulations for information technology devices, including electronic office machines for use in the office environment.
INSTRUCTIONS FOR MAINTENANCE If the LCD display element is broken and the liquid crystal solution leaks out of the display and onto your hands, clothing etc, wash your hands or clothing immediately with soap or alcohol, holding them under running water for at least 15 minutes. If the liquid comes into contact with your eyes, please consult a doctor immediately. Generally you should connect IT-devices only to power supply systems with separately guided protective earth conductor (PE), known as TN-S networks.
RECYCLING For further information of the stipulation look at your contract. All parts of the product which are subject to wear and tear are not included in the warranty engagement. Please order spare parts at the Wincor Nixdorf customer service. Recycling Environmental protection does not begin when time comes to dispose of the BEETLE; it begins with the manufacturer. The compact BA83 is manufactured without the use of CFCs and CCHS and is produced mainly from reusable components and materials.
ABBREVIATION INDEX Abbreviation Index CE cUL COM CPU DIN DVI-I EKC EMI EN ESD GS IEC IR ISO LED LCD LVDS MSR OSD POS sRGB SVGA TCO TFT USB UL VDE VESA VGA XGA European Symbol of Conformity Canadian Registration (Recognized by UL) Communication Port Central Processing Unit Deutsche Industrie Norm (German Institute for Industrial Standards) Digital Visual Interface Integrated Electronic Key Controller Electromagnetic Interference Europäische Norm (European Standard) Electrostatic Discharge Geprüfte Sicherhe
Herausgegeben von/Published by Wincor Nixdorf International GmbH D-33094 Paderborn Bestellnummer/Order No.
