Carpet Extractor Operating instructions (ENG) MODELS: 10080480 Read these instructions before using the machine.
Machine Data Label Overview This carpet extractor is an electrical powered, portable carpet extractor intended for commercial use. The appliance sprays a cleaning solution onto the carpet agitates the wet carpet, and then extracts the soiled solution back into the unit's recovery tank. The appliance is fitted with and a hand tool for cleaning upholstery and stairs. Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy.
Table of Contents Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How To Use This Manual . . . . . . . . . . . . . . . . . . . . . 4 Safety IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 5 HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . . 7 GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . . 9 SAFETY LABEL LOCATION . .
How To Use This Manual This manual contains the following sections: • • • • • The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The OPERATIONS section is to familiarize the operator with the operation and function of the machine.
Safety IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet. See Grounding Instructions. Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service. Use only indoors.
Safety IMPORTANTES MESURES DE SÉCURITÉ L'utilisation d'un appareil électrique demande certaines précautions: LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CET APPAREIL). Pour réduire les risques d'incendie, de choc électrique ou de blessure: Cet appareil ne doit être connecter qu a des prises ayant une sortie de terre. Ne pas laisser l'appareil sans surveillance lorsqu'il est branché. Débrancher lorsque l'appareil n'est pas utilisé et avant l'entretien.
Safety The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
Safety Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions : DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante : AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou entraîner la mort.
Safety GROUNDING INSTRUCTIONS 120 VOLT MODELS: THIS PRODUCT IS FOR COMMERCIAL USE ONLY. This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in "Fig. A". A temporary adaptor that looks like the adaptor in "Fig. C" may be used to connect this plug to a 2-pole receptacle as shown in "Fig. B", if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig.
Safety SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. Les ÉTIQUETTES D'AVERTISSEMENT suivantes se trouvent sur votre unité de nettoyage. Ces étiquettes signalent les avertissements et mises en garde importantes qui doivent être suivis en tout temps. Le non respect des avertissements et mises en garde pourrait entraîner des dommages matériels, des blessures graves ou même la mort.
Operations Technical Specifications ITEM Construction Vacuum Motor Solution Pump Brush Motor Brushes Cleaning Path Flow Rate Solution Spray Solution Tanks Recovery Tank Vacuum Shoe Wheels Power Cable Weight DIMENSION/CAPACITY Steel chassis with rotationally molded polyethylene tanks Three stage, bypass, 1.5 hp (1,119 watts), 100 cfm (2.8m³/min), 120" (3050 mm) waterlift 100 psi (7 bar) - Restorative 50 psi (3.
Operations ITEM Height Length Width Width of scrub path MEASURE 43 inches (1092 mm) 40.5 inches (1029 mm) 22 inches (559 mm) 16 inches (406 mm) HEIGHT LENGTH WIDTH Special Notes: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Operations How This Machine Works This carpet extractor is an electrical powered, portable carpet extractor intended for commercial use. The appliance sprays a cleaning solution onto the carpet agitates the wet carpet, and then extracts the soiled solution back into the unit's recovery tank. The appliance is fitted with and a hand tool for cleaning upholstery and stairs. The machine is designed to maintain your carpet using the Encapsulating Interim Carpet Cleaning Process.
Operations Components 1 2 3 4 8 6 7 5 9 1. Control Panel 6. Solution Fill Cover 2. Recovery Dome 7. Solution Drain Hose 3. Recovery Drain Hose 8. Solution Tank 4. Recovery Tank 9. Vacuum Shoe 5.
Operations Controls 3 5 1 2 4 6 7 1. Hand Tool Switch 5. Continuous Spray 2. Main Switch 6. Intermittent Spray 3. Light Cleaning 7. Intermittent Spray Buttons 4.
Operations Filling The Solution Tank REMOVE SOLUTION FILL COVER Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank. Do not allow water to spill into vacuum motor inlet. Dry spills from top of solution tank. Use only the suitable chemicals listed below. Using incompatible chemicals will damage the machine. Damages of this type are not covered under warranty. Carefully read ingredients on manufacturer's label before using any product in this machine.
Operations Pre Run Setup Remove electrical cord and literature from recovery tank. Fill solution tank (see filling instructions). STEP 1 Plug cord into grounded outlet. NOTE: Be sure dome is seated on recovery tank, and float shut-off is installed correctly. STEP 2 Switch the cleaning mode switch to the desired process. A for the encapsulating Interim Carpet Cleaning Process. B for Deep Extraction. STEP 3 Adjust handle to comfortable operating position.
Operations Pre Run Setup Lower machine to floor. STEP 5 Select continuous setting to start solution spray or select intermittent setting to enable use of trigger switches to start solution spray. The intermittent setting requires the operator to hold any one of the three trigger switches in the "on" position with the fingers, and is typically used in small areas where short cleaning passes are made.
Operations Operating The Machine 2 1 1. This machine can be operated in either direction. For smaller areas operate the machine by pulling rearward. 2. For larger unobstructed areas, flip the handle and use the machine's brush assisted propelling motion. STEP 1 Start at wall closest to power outlet. For small areas, pull straight back without pushing down on handle. STEP 2 1 ft.
Operations Operating The Machine Start at wall closest to power outlet. For large areas flip handle and operate machine in parallel passes, overlapping brush path. Clean perimeter last. ALTERNATE CLEANING PATH VACUUM INTAKE SOLUTION INTAKE STEP 5 During operation, observe the following: This machine is equipped with clear dome to facilitate operator viewing of dirty solution and vacuum air flow. During operation, observe the vacuum intake.
Operations To speed drying, use a Windblower™ fan. Empty recovery tank by releasing recovery drain hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use.
Operations Using The Hand Tool Use only acceptable accessory tools. See Optional Accessories section. To connect solution hose pull back collar and insert over machine mounted fitting, then release collar to lock into place. Solution connection can remain connected at all times. Disconnect vacuum hose and connect the hand tool to hand tool connection as shown. HAND TOOL CONNECTION SOLUTION QUICK DISCONNECT HAND TOOL POSITION Select hand tool switch. Squeeze handle on accessory tool to begin cleaning.
Maintenance Service Schedule MAINTENANCE Check machine for cord damage Check recovery dome and gasket for damage and cleanliness Check brushes - should be clean with no lint or strings attached Remove bearing cap from end of brush. Clean bearing and cap. Inspect vac shoe for blockage; remove fibers with coat hanger, etc.
Maintenance Components 6 2 4 1 LEFT 3A BOTTOM 3B 1. Vacuum Motor 4. Interim Solution Pump 2. Solution Strainer (Inside Tank Fitting) 5. Main Solution Pump 3A. Spray Jet-Extraction 6. Float Shut-off 3B.
Maintenance Periodic Maintenance Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow-dry. 3. After each use, rinse tank with fresh water.
Maintenance Circuit Protection CIRCUIT BREAKERS Circuit Breakers Circuit breakers interrupt the flow of power in the event of an electrical overload. When a circuit breaker is tripped, reset it by pressing the exposed button. If a circuit breaker continues to trip. The cause should be found and corrected. 15 Amp. Protects the vacuum motor. 8 Amp. Protects the brush motor.
Maintenance Scrub Deck 1 3 4 2 1. Scrub Brush Motor 2. Scrub Brushes 3. Retaining Clip 4.
Maintenance Scrub Head Scrub Brush Replacement The dual cylindrical scrub head is designed to scrub chemical into the carpet. The two counter rotating brushes raise the pile of the carpet, giving it a lush groomed appearance. The rear brush is the stiffer brush and is intended to scrub deeper and help propel the machine. It can be identified by its black color. The front brush is the softer brush and is intended to lift and groom the carpet pile. It can be identified by the white bristles.
Maintenance Vacuum Motor Carbon Brushes End Cap Carbon Brushes The green ground wire must be attached for safe operation. See wiring diagram. If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely. 3 [9.
Maintenance Troubleshooting PROBLEM No Power, Nothing Runs Vacuum Motor Will Not Run Vacuum Motor Runs But Suction Is Poor CAUSE Is the cord plugged in. Plug in cord. Circuit breaker tripped in building. Faulty switch. Faulty power cord or pigtail. Reset breaker. Call for service. Call for service. Vacuum circuit breaker tripped. Reset breaker. Faulty main vacuum switch. Loose wiring. Faulty vac motor. Call for service. Call for service. Call for service. Debris lodged in vac shoe.
Parts PARTS 86302100 CLIPPER DUO 31
Brush Deck 32 86302100 CLIPPER DUO
Brush Deck REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13A 13B 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 86223780 86224170 86012800 86012810 86223520 86223310 86215250 86224660 86173330 86014990 86215870 86012780 86216050 86295520 86223490 86224130 86343870 86294070 86012790 86172970 86222870 86217780 86219390 86173350 86172980 86224630 86277130 86215230 86294060 86350490 8 2 2 1 3 1 1 1 1 9 1 2 1 1 2 1 1 1 2 3 1 1 1 4 2 2 7 1 1 3 DESCRIPTION SCR, M4X8, SET, ISO4029,CP,BLK SHAFT, 6.
Brush Deck Motor 34 86302100 CLIPPER DUO
Brush Deck Motor DESCRIPTION SERIAL NO. FROM REF PART NO.
Brush Deck Mounting 1 7 7 8 2 3 4 21 2 10 3 15 19 5 2 11 4 12 16 9 6 13 20 3 17 18 14 36 3 86302100 CLIPPER DUO
Brush Deck Mounting REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO. QTY 86302710 86270830 86010670 86259410 86296450 86228990 86277130 86295010 86294940 86294950 86270990 86010650 86071800 86225790 86006580 86301870 86008460 86296480 86295020 86271840 86361560 1 11 13 4 1 4 8 1 1 1 4 4 2 1 2 1 2 2 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES DEFLECTOR, SPRAY NUT, 5/16-18 HEX NYLOCK SS WASHER, 5/16 FLAT SS WASHER, THRUST .51 ID X 1 OD X .063 BRKT, DECK ARM CROSSBAR BEARING, FLNGD, .
Control Panel 22 7 15 17 1 13 14 16 7 8 19 6 26 11 16 4 19 3 2 12 9 23 21 25 20 24 16 5 18 10 25 38 86302100 CLIPPER DUO
Control Panel REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART NO. QTY 86002010 86001980 86215670 86308020 86173030 86173300 86005640 86172640 86223010 86301820 86224730 86224930 86007130 86007200 86007140 86010640 86295700 86298820 86276820 86298690 86297750 86233170 86234110 86298810 86006620 86005700 2 1 1 1 4 1 3 1 1 1 1 1 1 1 1 4 1 1 5 1 1 1 1 1 4 1 DESCRIPTION SERIAL NO.
Decal 5 1 2 3 4 6 40 86302100 CLIPPER DUO
Decal REF 1 2 3 4 5 6 PART NO. QTY 86221470 86244680 86004970 86298670 86295620 86390460 1 1 1 1 1 1 DESCRIPTION SERIAL NO.
Hand Tool 4 3 5 2 1 42 86302100 CLIPPER DUO
Hand Tool REF 1 2 3 4 5 PART NO. QTY 86200810 86293280 86293290 86293500 86293750 1 1 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES NIPPLE, 1/8 FPT QD FEM BRASS HOSE, 1/4" RETRACTABLE HOSE ASM, 38.
Handle 3 1 5 1 1 2 10 11 8 7 6 4 9 44 86302100 CLIPPER DUO
Handle REF 1 2 3 4 5 6 7 8 9 10 11 PART NO. QTY 86312730 86224500 86218660 86223830 86173000 86293400 86218960 86218950 86218640 86218630 86216500 3 4 1 1 3 4 1 2 1 1 2 DESCRIPTION SERIAL NO. FROM NOTES SWITCH, HANDLE SPACER, HANDLE EXTRUSION HANDLE, GRIP SCR, M8X40, SHCS, ISO 4762, SST SCR, KA40X20, PT OVAL, WN1412, PL SCR, M5X12 SHCS GR 10.
Handle Bracket 15 15 13 12 17 3 14 4 9 10 2 1 6 11 16 3 10 7 8 4 5 46 86302100 CLIPPER DUO
Handle Bracket REF PART NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 86276800 86279170 86296830 86296860 86296880 86296890 86296920 86296970 86296980 86302860 86298840 86233170 86005640 86274400 86298830 5 6 2 2 1 1 1 1 1 2 1 1 1 4 2 SCR, 10-32 X 3/8 HHMS SS WASHER, #10 X 1.0 FLAT BRKT, HANDLE PIVOT PLATE, HANDLE PIVOT LATCH LEVER, HANDLE RELEASE LEFT LEVER, HANDLE RELEASE RIGHT BRKT, HANDLE TANK MOUNT MECHANISM MOUNT, LEFT MECHANISM MOUNT, RIGHT SPRING, EXT .25D X 1.13L X .031W SCR, 10.
Handle Mounting 2 7 6 2 8 4 5 3 1 4 48 86302100 CLIPPER DUO
Handle Mounting REF 1 2 3 4 5 6 7 8 PART NO. QTY 86274400 86006950 86276490 86010670 86345230 86295770 86297220 86379640 2 6 6 6 2 2 1 2 DESCRIPTION SCR, 1/4-20 X 5/8 BHCS SCR, 10-32 X 1/2 PPHMS BLK NP SCR, 5/16-18 X 5/8 HHCS SS WASHER, 5/16 FLAT SS CAP, BRUSH ASM, CLP DUO CAP, HANDLE, INNER PANEL, CONN. ACCESS WASHER, NYL, RETAINING, #10, .03 THK SERIAL NO.
Handle Release Lever 3 7 5 10 4 6 9 15 17 16 11 8 12 2 14 18 1 13 4 50 86302100 CLIPPER DUO
Handle Release Lever REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO. QTY 86215240 86215630 86216870 86008650 86218190 86218020 86221730 86222280 86295820 86221840 86222550 86222990 86173030 86293370 86224540 86254970 86259400 86225950 2 1 1 4 2 1 1 4 2 1 1 1 4 4 4 1 1 1 DESCRIPTION SERIAL NO.
Recovery Tank 1 2 7 8 6 3 9 5 10 4 11 52 86302100 CLIPPER DUO
Recovery Tank REF PART NO. QTY DESCRIPTION 1 86293520 1 DOME ASM, CLIPPER DUO 2 3 4 5 6 7 8 9 10 11 86218180 86003630 86299180 86297250 86006950 86004500 86004510 86002400 86296640 86233140 1 1 1 1 2 1 1 1 1 1 GASKET, DOME FLOAT SHUT-OFF TANK, RECVRY, DK GRAY (TRIMMED) HOOK, WIREFORM, HANDTOOL SCR, 10-32 X 1/2 PPHMS BLK NP HOSE, CAP HOSE, INSERT CLAMP, 2.0" WORM GEAR X .312W HOSE, 1.5 X 19.0 DRAIN CLAMP, 2.0" WORM GEAR 86302100 CLIPPER DUO SERIAL NO.
Solution 2 4 18 19 3 11 15 7 17 13 14 12 8 1 9 16 5 10 3 6 14 15 54 86302100 CLIPPER DUO
Solution REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 PART NO. QTY 86308240 86367130 86218360 86367120 86005640 86273930 86006790 86274290 86298840 86010650 86367640 86294700 86294720 86297930 86298120 86299120 86390430 86004350 86364240 1 1 2 1 4 2 2 2 4 4 1 1 1 2 1 1 1 1 1 DESCRIPTION SERIAL NO.
Solution 56 86302100 CLIPPER DUO
Solution REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 PART NO.
Solution Tank 58 86302100 CLIPPER DUO
Solution Tank REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART NO. QTY 86200820 86260690 86233110 86233090 86234790 86238460 86373610 86197920 86301930 86006860 86276160 86276290 86276490 86277050 86240790 86010650 86010670 86297620 86297990 86299390 86299530 86299590 86390420 86270920 86273950 86246080 1 1 1 1 1 1 1 1 1 4 1 3 1 1 1 4 1 1 1 1 1 1 1 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES NIPPLE, 1/8FPT QD ,MALE BRASS HOSE ASM, FCT ADPTR X 60" NBRD CLAMP, 1.
Vacuum Shoe 60 86302100 CLIPPER DUO
Vacuum Shoe REF 1 2 3 4 5 6 7 8 9 10 PART NO. QTY 86225650 86218110 86218270 86218260 86223230 86172950 86293170 86293190 86293180 86218250 1 1 2 1 1 12 1 2 1 1 DESCRIPTION SERIAL NO.
Vacuum Shoe Mounting 62 86302100 CLIPPER DUO
Vacuum Shoe Mounting REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PART NO. QTY 86003010 86004290 86002390 86297470 86276490 86010670 86295030 86278280 86296510 86005810 86259420 86272750 86010730 86298080 86259410 86010630 86273750 86293160 86300340 86014990 1 1 1 1 2 2 2 2 1 2 2 1 1 2 2 2 2 2 1 1 DESCRIPTION SERIAL NO. FROM NOTES CUFF. HOSE 1.5" BLK A 2161 HOSE, 1.5 BLK VAC X 45" CLAMP, 1.75" WORM GEAR X .
Vacuum 1 2 3 6 4 5 64 86302100 CLIPPER DUO
Vacuum REF 1 2 3 4 5 6 PART NO. QTY 86300300 86217480 86299250 86002390 86004290 86302620 4 1 1 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES SCR, #8 X 2" PPHSMS COVER, VAC MOTOR ASSY, VAC MOTOR CLAMP, 1.75" WORM GEAR X .312 HOSE, 1.
Wheel & Axle 3 4 2 1 5 6 7 2 1 66 86302100 CLIPPER DUO
Wheel & Axle REF 1 2 3 4 5 6 7 PART NO. QTY 86276490 86010670 86219480 86001660 86226050 86010730 86294920 5 5 2 2 2 2 1 DESCRIPTION SERIAL NO. FROM NOTES SCR, 5/16-18 X 5/8 HHCS SS WASHER, 5/16 FLAT SS HUBCAP, 9.75" WHEEL HUBCAP, 5/8" SHAFT WHEEL, 9.75" X 1.5" WASHER, 5/8 ID X 1.18 X .
Wiring Diagram HANDLE CONSOLE BLU BLU BLU HANDLE SWITCH #2 HANDLE SWITCH #1 HANDLE SWITCH #3 BLK BLK BLK BLU 4 ORG 6 VAC MOTOR CIRCUIT BRKR 9 3 9 8 RELAY BLU SWITCH SWITCH SWITCH 90 F/I 90 F/I DEEP CLEAN ALL ON 1 90 F/I BRN 5 PIGGYBACK BLU 9 90 F/I PIGGYBACK 90 F/I BLK CONTINUOUS 90 F/I 90 F/I WHT 90 F/I WHT RED 13 14 PIGGYBACK PIGGYBACK BRUSH MOTOR CIRCUIT BRKR 90 F/I ORG TRANSFORMER 90 F/I ACCESSORY 90 F/I LIGHT CLEAN BUTTON SPRAY PIGGYBACK WHT RED BLK 5 7 CTRL P
Wiring Diagram REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. QTY 86296060 86297750 86298180 86296010 86296020 86295980 86268210 86295990 86296000 86299330 86299370 86299340 86299360 86294220 86312170 1 1 1 2 1 1 1 2 2 1 1 1 1 1 1 DESCRIPTION SERIAL NO.
Suggested Spare Parts PART NO. 86215250 86216050 86295520 86002010 86001980 86215670 86218290 86348660 86007200 86007140 86218180 86003630 86299250 86298070 86297440 86012550 86201110 86234790 86256090 86004570 86293170 86297870 70 DESCRIPTION SERIAL NO.
Serial Numbers REF. NO.
Notes: 72 86302100 CLIPPER DUO
