CARPET EXTRACTOR Operating Instructions (ENG) Models: ADP, ADPJ QUEST . . . for Continuous Improvement. Windsor's Quality Management System is Certified IS0 9001. UL LISTING COVERS ADP ONLY Read these instructions before operating the machine.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING MACHINE l Connect machine to a properly grounded outlet only. See grounding instructions. l Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. l Use indoors only. Do not use outdoors or expose to rain. l Do not allow to be used as a toy.
Equipment Set- Up: CONTROLS 1. Before operating the ADP become familiar with the controls located at the back of the machine and on the control panel. 2. Connect hoses to dome. Loop power cord through strain relief as shown. 3. Become familiar with the machine.
IMPORTANT SHIPPING NOTE Carefully unpack your scrubber and inspect it for shipping damage. Any damages which occurred during shipping are the responsibility of the carrier, who must be notified immediately. ELECTRICAL: In the USA this vacuum operates on a standard 15 amp 115 volt A.C. power circuit (12OV nominal). Special voltage models are available for international applications. The amp, hertz, and voltage are listed on the data label found on each machine.
OPERATING THE ADP Remove clear dome from upper tank. Do not remove the two vacuum hoses. NOTE: Dome can be set securely between handle uprights when the handle is in operating position. 1. Vacuum the carpet and make sure it is cleared of surface debris before cleaning with the ADP. 2. Release handle lock lever located on the lower right side of the handle and lower handle to a comfortable operating position. Lock the handle in position. Lift upper recovery tank from machine and set aside.
. Lower machine to floor. Dispense solution by using either the continuous pump switch or the intermittent pump switch. Use the continues pump switch for large open areas. Use the intermittent pump switch for small confined areas. Walking backwards, move the extractor over the area to be cleaned. The extractor’s brush assistance allows the machine to moved quickly and easily over the carpet. Remember to turn off the pump switch about six inches before the end of each pass. To Use an Accessory Tool: 1.
SWITCH CONTROL PANEL ADP MAINTENANCE INSTRUCTIONS WARNING: Removethe machine power cord from the electrical source before making any adjustments or repairs. ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM REPAIRS. HANDLE LOCKADJUSTMENT The black knob on the opposite end of the rod from the adjusting lever controls the tightness of the adjusting knob. The switches and circuit breakers are accessed through the panel located on the bottom of the control panel.
POTENTIAL INJURY: DAILY MAINTENANCE: Warning: These procedures are followed at the end of each work period to extend the life of the machine. This product contains moving parts. 1.) Empty unused cleaning solution by disconnecting clear hose on back of machine and pouring into floor drain. 2.) Inspect and clean solution filter screen inside tank and vac intake screen inside dome. 3.) Flush the system. Fill solution tank with 1 or 2 gallons (4 - 8 liters) of clean ot water.
PERIODIC MAINTENANCE: These procedures are performed by a trained service technician. The regularity of these procedures may depend on the machine’s use. 1.) Flush the system with a special solution to reduce scaling (alkaline build-up). Use acetic acid (white vinegar) or an anti-browning solution. Mix one quart acetic acid with 2 gallons (1:8 liters) of hot water in the solution tank (if an anti-browning solution is used follow manufacturer’s instructions).
TROUBLESHOOTING CHART Condition Corrective Action No Power To Machine: Dead electrical circuit breaker in fuse box Check building circuit breaker. Faulty power cord Replace Power switch failure Test switch for continuity/Replace if necessary. Faulty circuit breaker Test circuit breaker for continuity/Replace if necessary. Internal wiring problem With the machine unplugged, check for, and correct, any loose wire connections inside the machine at the switches and terminal block.
TROUBLESHOOTING CHART Condition Corrective Action Accessory Tool Fitting Difficult to Connect: Corrosion on fitting Clean with steel wool. Remove and soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant. Carpet Not Getting Clean: Severe soil conditions Make several passes at right angles to each other. Use a prespray. Carpet Too Wet: Worn spray jet(s) Replace spray jets which are producing more than a fine mist.
SERVICING THE VAC MOTOR Vote: When replacing carbon vac motor brushes loosen wire terminal BEFORE removing screws on bracket f armature commutator is not concentric, extremely pitted, or grooved the motor will need to be replaced or sent to a qualified service center to restore vac performance. Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.
VAC MOTOR ASM Parts List 2 3 4 5A 5B 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 73215 87013 57047 53134 53183 20046 39231 54070 57039 29135 70363 87018 70011 87025 34228 57082 14242 88345 87016 70191 14042 Spacer, 3/8 OD x l/4 Washer, l/4 Flat Nut, l/4-20 Nylock Vac Motor, 11 n/ 3 Stage TD TB Vac Motor, lOOV3AStageTDTB Clamp, 2.25 Worm Gear Hose, UL Vac Exhaust x 12 Muffler Asm. ADM Vac exhaust Nut, 1.
VAC SHOE ASSEMBLY AND BRUSH PRESSURE MECHANISM 14 I 98198 10/1/98
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 73040 51247 62115 70363 70166 70018 73178 14244 87025 66073 87013 87030 70020 57047 57085 57022 03027 67082 89061 85028 87008 87016 70088 67005 36050 87074 73181 70190 05016 70057 35233 Spring, #55 Music Wire Lever Asm, Roller Adjustment Plate, Height Adj. Scr, 10-32 x 3/8 PHTR Scr, l/4-20 x l/2 FHMS Scr, l/4-20 x 1.
TANKS & VAC HOSE ASSEMBLIES NOTE: Each tank has a filter screen which protects the machine’s internal parts from damage. Ensure that these screens are in place and clean before operating the machine.
TANKS AND WC HOSE ASSEMBLY Parts List RECOVERY TANK PARTS LIST: SOLUTION TANK PARTS LIST: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 39241 39234 40068 57105 70251 14630 70020 40027 73864 75251 50622 18 19 20A - 20B 50534 50503 21 - 22 87013 Hose, l/2” Wirebound X 10” Hose, Drain w/sol’n Level -ADP Hosebarb, 3/8 NPT x l/2 Tee Open Nut, l/4-20 w/Star Washer Set Scr, l/4-20 x 1.
PUMP REPAIR, MANIFOLD & VALVE Spray Jets The ADP is equipped with quick change jet nozzles which are easy to clean or replace. 1.) With tanks empty, tilt machine back. Rinse in hot water or use compressed air to clean. Nozzles can also be soaked in an acetic acid solution (white vinegar). CAUTION: Do not use pins or wires to clean or unclog jets. Using wires or pins may ruin spray pattern.
PUMP REPAIR, MANIFOLD, & VALVE Parts List 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 44051 44052 44055 14523 70114 87025 70085 54094 66095 40014 84065 20042 39311 14454 20035 70088 87016 57081 65154 56014 40033 78156 31016 87015 56012 57116 14020 20015 57104 70066 70210 73201 57107 40038 39279 84098 40042 Jet Seal, Mini-Quick Jet Body w/ Seal, Mini-Quick Jet Assembly, 11003 Mini-Quick Brkt, Manifold Scr, #lO x 3/4 Polyfast washer, l/4 star scr, l/4-20
CONTROL PANEL / MAIN HANDLE ASSEMBLY 20 98198 7/1/97
MAIN HANDLE ASSEMBLY Parts List 2 3 4A 4B 5 6a 6b 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 47 48 49 50 50184 72067 50451 50554 72068 14530 14832 73169 14942 70253 57107 62153 70082 73180 38225 57104 36123 70092 26009 23086 26006 70361 41144 70117 48012 87067 41236 89114 05076 73214 70189 20084 67073 03073 27226 51039 66068 87100 50534 50503 88885 27371 7320 1 26015 23506 73200 57106 14022 57040 70252 14700 27376 Label, Windsor Switch, 125V SPST Lit Rkr w/BT Label,
BRUSH DRIVE ASSEMBLY Belt Replacement Periodically check the drive belt for wear. Replace worn or frayed belts before they break, when possible. To access the belt remove the belt cover. To replace the belt it is necessary to loosen the motor and remove the brush. The “preset” belt tension is correct when the motor and belt are securely back in place. Check pulley alignment and correct if necessary. The brush pulley and motor pulley can be aligned using a straight edge.
BRUSH DRIVE ASSEMBLY Parts List 2 3 4 5 6 15A 15B 15C 16A 16B 17 18 19 20 21 22 23 24 25 26 27 28 09019 64022 14219 03033 36054 70190 73181 70562 41109 70011 87025 70020 57123 88552 88883 88884 53093 53173 87018 70074 36044 70363 11015 57047 36050 70434 36043 70015 87161 67005 Bearing, Brush Pulley, Motor Brush. ADP assemblv Axle, Brush * Guard, Thread Scr, l/4-20 x l/2 BHCS Spacer, .259 ID x .38x .
98198 7/15/98
We supply the power I 98198 7/1/97
