SCRUBBER Operating Instructions (ENG) Bedienungsanleitung (GER) Istruzioni operative (ITA) Manuel d’utilisation (FRE) MODELS: SGE28 10052480 SGEO28 10052510 SGE32 10052490 SGEO32 10052520 SGE36 10052500 AFTER SN: 1000136404 IPX4 Read these instructions before using the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen Leggere attentamente le presenti istruzioni prima di azionare la macchina Lire ce manuel avant d’utiliser la machine AB 86037550 01/27/12 PRV NO.
MACHINE DATA LOG/OVERVIEW MODEL _______________________________________ DATE OF PURCHASE __________________________ SERIAL NUMBER ______________________________ SALES REPRESENTATIVE # _____________________ DEALER NAME ________________________________ OPERATIONS GUIDE NUMBER ___________________ PUBLISHED __________________________________________ YOUR DEALER Name: __________________________________________________________________________________________________ Address: _____________________________________
TABLE OF CONTENTS Machine Data Log/Overview................................2 Table of Contents.................................................3 Service Schedule. ............................................. 4-17 Machine Troubleshooting.................................. 4-18 HOW TO USE THIS MANUAL GROUP PARTS LIST How to use this Manual........................................1-1 Brake. ...................................................................5-1 Circuit Breaker...............................
HOW TO USE THIS MANUAL This manual contains the following sections: - - HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.
IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. ! WARNING: To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: ! WARNING WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. SAFETY DECAL 86252530 PRV NO. 81494 BATTERY CAUTION 86252520 PRV NO. 80885 PINCH POINT WARNING 86243830 PRV NO. 500663 CIRCUIT BREAKER 86244130 PRV. NO 500859 - 28 IN & 32 IN 86244140 PRV NO. 500861 – 36 IN HORN DECAL 86248210 PRV NO. 81349 PINCH POINT WARNING 86243830 PRV NO.
TECHNICAL SPECIFICATIONS ITEM Nominal power Rated Voltage Rated Amperage Batteries Scrub Brush Motors Vacuum Motor(s) Propelling Motor Mass (GVW) Weight empty without batteries Solution Control Solution tank capacity Recovery tank capacity Scrub brush diameter for 28 in. (71 cm) disk scrub head Scrub brush diameter for 32 in. (81 cm) disk scrub head Scrub brush diameter for 36 in.
TECHNICAL SPECIFICATIONS ITEM Height 1 Height 2 Length Width without squeegee and scrub head Width of squeegee Width of scrub path for 28 in. (71 cm) Width of scrub path for 32 in. (81 cm) Width of scrub path for 36 in. (91 cm) MEASURE 51 inches (130 cm) 56.6 inches (144 cm) 63.
HOW THE MACHINE WORKS The Saber Glide is a battery powered, selfpropelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system, recovery system, and operator control system. The function of the solution system is to store cleaning solution and deliver it to the scrub system.
COMPONENTS 11 1 6 5 3 2 7 10 4 12 13 1. 2. 3. 4. 5. 6. 7. Control panel Front cover Side cover Tank Recovery tank cover Recovery tank dome Recovery tank drain hose 9 8 8. Scrub head 9. Scrub head side squeegee 10. Solution tank drain hose 11. Solution tank cover 12. Squeegee 13.
CONTROLS 3 7 5 6 4 9 11 1 2 21 18 17 20 15 19 8 16 20 13 10 14 21 3-5 GLIDE 86037550 01/09/07 12
CONTROLS 1. 2. 3. 4. 5. 6. 7. Key switch Emergency stop button One touch switch Brush pressure switch Solution control switch Vacuum/squeegee switch Display toggle switch • Information Screen 1 • Information Screen 2 • Hour meter • Fault codes and special icons • Battery meter 8. Scrub Deck Shift Switch (36in only) 9. Recycle switch (optional) 10. Recycle indicator light (optional) 11. Headlight switch (optional) 12. Brake pedal 13. Parking brake lever 14.
CONTROLS 3. ONE TOUCH SWITCH This switch controls the scrub brushes and vacuum all in one touch. To start scrubbing, press the one touch switch. The brush drive motors will turn on, the scrub deck will lower to the "light scrub" position, the solution will flow at “two bars” rate, the squeegee will lower and the vacuum will turn on. The information display window will show which functions are operating.
CONTROLS 5. SOLUTION CONTROL SWITCH This switch controls the amount of solution flow to the scrub deck. There are 7 different flow settings. To increase the solution flow, press the solution control switch (+). To decrease solution flow, press the top of the switch (-). If the brush motors are turned off or the direction control pedal is in neutral, the flow is automatically interrupted until the motors are turned on again, or the drive pedal is moved forward or reverse.
CONTROLS 7. DISPLAY TOGGLE SWITCH The display toggle switch allows you to change the information display screen. Two screens are available. • INFORMATION DISPLAY –SCREEN 1 • INFORMATION DISPLAY –SCREEN 2 • The hour meter is viewed on screen 2 of the information display. Hours are displayed for key ON time, brush run time, and traction motor time. Key ON Hours: Records the entire time that the key is on. Brush Run Time: Records the time spent with the brushes running and gives true brush motor time.
CONTROLS • The float switch is located inside the recovery tank. The purpose of the float switch is to notify the user that the recovery tank is full. When the float switch is activated, the scrub brush motors and solution flow will stop, the scrub deck will raise, the squeegee will rise after 60 seconds, and the vacuum motor will turn off 10 seconds later. • The battery meter can be viewed at the left side of either information screen 1 or information screen 2.
CONTROLS 9. RECYCLE SWITCH (OPTIONAL) This switch controls the solution recycle pump. To start recycle pump, press the switch. A green light above the circuit breakers will indicate that pump is on. The solution control switch will control the speed of the pump and therefore the amount of solution flow to the scrub deck. Make sure there is an adequate amount of water in recovery tank before starting recycle pump, and turn off recycle pump when water level reaches filter.
CONTROLS 12. BRAKE PEDAL The brake pedal is located on the floor to the right side of the steering column pedestal. The pedal operates the disc brake on the drive wheel. To slow or stop the vehicle, apply pressure to the brake pedal. 13. PARKING BRAKE LEVER The black knob located on the right side of the steering column pedestal is used to set the parking brake. To set the parking brake, fully depress the brake pedal and push the parking brake knob.
CONTROLS 15. STEERING WHEEL The steering wheel turns the front wheel causing the machine to change direction. 16. STEERING TILT LEVER The steering tilt lever is located on the right side of the steering wheel. To engage the tilt adjustment, pull on the lever and adjust the steering column to desired position. Release lever and allow it to lock into desired position. 17. HORN BUTTON The horn button is located on left side of the steering column. The horn is activated by pressing the horn button. 18.
MACHINE OPERATION PRE-RUN MACHINE INSPECTION 1. Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. Visually check for exterior damage, leaks, damaged or worn tires. 2. Check brushes or pads and drivers for proper installation and wear. Weekly check scrub deck skirts for proper contact with floor. See BRUSHES in MAINTENANCE SECTION. 3. Check squeegee for wear and proper adjustment.
MACHINE OPERATION EMERGENCY STOP PROCEDURE TO BEGIN SCRUBBING When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children. 1. Place right foot on brake pedal or check to make sure parking brake has been set. 2. With directional pedal in neutral turn key switch to “ON”. 3. Release brake. 4. Press the directional pedal to travel in the desired direction and steer to the start of the scrub pattern. 5.
MACHINE OPERATION EMPTYING AND CLEANING TANKS RECOVERY TANK 1. Touch the one-touch switch (#1) on the control panel to raise the scrub deck, stop the motors, and solution flow, raise the squeegee and turn off vacuum motors. 2. Park the machine next to a floor drain. Drain hose is on left rear corner of machine. 3. Turn off the key switch and set the machine’s parking brake. 4. Unhook the drain hose from retainer. Unscrew T-handle on plug enough to loosen plug and lower hose in direction of drain.
MAINTENANCE 14 7 6 1 15 11 8 3 13 16 2 17 9 12 4 5 10 1. 2. 3. 4. 5. 6. 7. 8. 4-1 Batteries Battery Tray Drain Hose Squeegee Adjustment Side Squeegee Adjustment Scrub Brushes Vacuum Filter Float Switch Solution Strainer 9. 10. 11. 12. 13. 14. 15. 16. 17.
MAINTENANCE 1. BATTERIES The batteries provide the power to operate the machine. The batteries require regular maintenance to keep them operating at peak efficiency. To get the greatest life from the batteries charge them when their charge level reaches 25%of a full charge. Use a hydrometer to check the charge level. Do not allow the batteries to remain in a discharged condition for any length of time. Never expose a discharged battery to temperatures below freezing.
MAINTENANCE TO CHARGE BATTERIES When servicing machine, avoid contact with acid. ! WARNING Batteries emit hydrogen ! WARNING gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Wear eye protection and protective clothing when working with batteries. ! WARNING ! WARNING 8. Plug the charger into the battery connector. Plug battery charger into power outlet. The charger gauge should indicate that the batteries are charging.
MAINTENANCE TO REMOVE BATTERIES TO REPLACE BATTERIES 1. Stop the machine in a clean area next to the charger. 2. Turn off machine and set parking brake. 1. Refer to diagram. Place batteries in battery compartment. 2. Connect all jumper cables positive to negative to the six batteries. 3. Connect the positive cable to battery in the position shown. 4. Connect negative cable to battery in the position shown.
MAINTENANCE 3. SQUEEGEE ADJUSTMENT TO ADJUST SQUEEGEE DEFLECTION Adjusting the squeegee is a two-part process. First, the squeegee tool must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The pitch adjustment is facilitated by the use of a spirit level mounted on the squeegee tool. The second adjustment is the amount of deflection or down pressure on the squeegee. TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface.
MAINTENANCE TO REPLACE OR ROTATE REAR SQUEEGEE BLADES TO REPLACE OR ROTATE FRONT SQUEEGEE BLADES 1. With the squeegee in the up position, turn off the key switch and set the parking brake. 1. With squeegee assembly on bench, loosen retaining bolt and locking nut on the left side of the retaining strap. 2. Remove front retainer strap. 3. Remove squeegee blade from locating pins on squeegee tool and rotate to new position or replace as required. 4. Install blade on locating pins of squeegee tool. 5.
MAINTENANCE 4. SIDE SQUEEGEE ADJUSTMENT TO REPLACE OR ROTATE SIDE SQUEEGEE BLADES (28 in. & 32 in.) 1. Loosen the locking knob and pivot the side squeegee out as if to expose the brush. 2. Loosen and remove the three nuts and bolts securing squeegee blades. 3. Remove the retaining strap and squeegee blade and rotate or replace squeegee blade. 4. Install blade and retaining strap on locating pin and reinstall three bolts and nuts. 5. Tighten nuts.
MAINTENANCE 5. SCRUB BRUSHES REPLACING OR INSTALLING SCRUB BRUSHES There are five different types of brushes available to cover applications from cleaning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market and further add to the flexibility of the machine. Please refer to the following to assist in selecting the proper brush or pad for the work at hand.
MAINTENANCE 3. Locate release lever on top of brush or pad driver. With finger rotate release lever against spring pressure counter clockwise. Brush/pad driver will release and drop down. 4. To reinstall, center the cut out of the release lever plate on brush/pad driver to be installed under the brush drive hub. 5. Raise brush/pad driver up until assembly contacts brush hub. Rotate slightly until driver engages release lever plate. 6.
MAINTENANCE 11. VACUUM MOTOR Vacuum Motor Carbon Brushes Replacement (Ametek) End Cap (Refer to the Vacuum Group in the parts section of manual) Carbon Brushes ! WARNING Do not use a pressure washer to clean around the vacuum motors. Use tap pressure only. Care must be taken so that water is not directed into vacuum motor air intakes. CHANGING VACUUM MOTOR 1. Remove side cover. 2. Disconnect electrical connector to the vacuum motor. 3. Loosen clamp and disconnect hose from vacuum intake. 4.
MAINTENANCE BRUSH MOTOR CARBON BRUSH REPLACEMENT 12. BRUSH MOTOR (Refer to Brush Motor Group in parts section of manual). ! WARNING Do not use a pressure washer to clean around the brush motors. Use tap pressure only. CHANGING BRUSH MOTORS 1. With the scrub deck in the stored position, disconnect brush motor wiring connector from harness. 2. Loosen side squeegee locking knob, and pivot side squeegee away from scrub deck to access and remove scrub brushes or pad drivers. 3.
MAINTENANCE 13. TRACTION MOTOR 14. FUSE Do not use a pressure ! WARNING washer to clean around the brush motors. Use tap pressure only. TRACTION MOTOR CARBON BRUSH REPLACMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key. 1. Disconnect batteries from machine. 2. Turn the steering wheel fully to the right. 3. Disconnect the electrical connection to the traction motor (keeping note of which wire is positive and negative).
MAINTENANCE 16. SQUEEGEE ACTUATOR REMOVAL/REPLACEMENT SQUEEGEE ACTUATOR ADJUSTMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake. 1. Remove squeegee to gain access to lift system. 2. Lower squeegee lift linkage, if possible, by pressing bottom of vacuum/squeegee switch and turn key to the off position. 3. Remove lower clevis pin by removing rue ring and washer from clevis pin, then pull pin out from squeegee lift bracket and actuator. 4.
MAINTENANCE 17. SCRUB DECK ACTUATOR REMOVAL/REPLACEMENT SCRUB DECK ACTUATOR ADJUSTMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake. The actuator will need to be adjusted when replaced. The actuator needs to be set such that the scrub deck stops barely touch the rubber bumpers on the frame in the raised/retracted position. 28 IN. & 32 IN. To adjust the actuator: 1.
TRANSPORTING MACHINE TOWING OR PUSHING MACHINE PREPARATION FOR TRANSPORTING The machine may be towed for short distances at speeds not to exceed 5 mph. Be careful to avoid damaging machine. Attach towing device at tie down point. The machine may be pushed by hand from the rear. NOTE: To avoid damage caused by regenerative voltage, disconnect traction motor before towing or pushing machine. Remove squeegee tool to eliminate interference with tie-downs. Scrub head must be in the up position before loading.
JACKING MACHINE MACHINE JACKING MACHINE STORAGE The machine may be jacked up for service or inspection by using the specified jack locations. Always block the tires when jacking up the machine. If the machine is to be stored for extended periods of time, the following steps must be taken to minimize the chance of corrosion or deposits forming. FOR SAFETY: Before leaving or servicing machine; Stop on level surface, set parking brake, turn off machine and remove key. 1.
MAINTENANCE SERVICE SCHEDULE MAINTENANCE BEFORE EACH WORK PERIOD Check water level of batteries after charging; add distilled water if necessary Check that recovery tank cover seals tightly Visually check for damaged or worn tires Check brushes or pads for proper installation Check vacuum hose connections Check that squeegee is securely attached and properly adjusted Check that side squeegees are properly adjusted Check for securely attached drain hose, plug and caps Check brakes and steering for proper o
MACHINE TROUBLESHOOTING ERROR CODE PROBLEM CAUSE No power to machine Battery disconnected Little or no propel Emergency shut-off activated Battery cables corroded Main fuse blown Faulty key switch Low battery charge Clean connections Replace fuse Replace switch Charge batteries Machine turned on with pedal not in neutral position Wheels spin Allow pedal to return to neutral Restart.
MACHINE TROUBLESHOOTING PROBLEM CAUSE Vacuum motor does not run, or runs slowly Recovery tank full Drain recovery tank Recovery tank float switch dirty Loose motor connection Clean float switch Poor scrubbing performance ERROR CODE 7700 Worn vacuum motor brushes Debris caught in scrub brushes Worn brushes or pads SOLUTION Check motor wires and connections Replace brushes, check commutator Remove debris Replace brushes or pads Improper detergent, brush or pad used Low scrub brush down pressure L
MACHINE TROUBLESHOOTING - CONTROLLER FAULT CODES ERROR CODE None PROBLEM SOLUTION LCD display on, but incomplete 0A01 Power down error 0204 All 080_ codes All 140 _ Codes All 310_ Codes Memory corrupt Throttle wiring Disconnect batteries and wait 1 minute before re-applying power. Disconnect batteries and wait 1 minute before re-applying power. Replace controller. Check for short or open circuits in throttle wiring. Check for short circuit between B+ and traction output. Check for short circuits.
BRAKE 5 6 27 4 25 2 1 4 24 30 3 23 26 29 28 7 22 7 13 8 20 21 19 18 18 9 13 10 11 17 14 16 14 12 13 15 9 5-1 GLIDE 86037550 01/09/07
BRAKE REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 14A 14B 14C 14D 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PART NO. 86276880 86278940 86255560 86279620 86355600 86355540 86008670 86248980 86273810 86010780 86010630 86215650 86005810 86073850 86135470 86134940 86135480 86010330 86251790 86271600 86065800 86273820 86254960 86066010 86087430 86252040 86078400 86005860 86276890 86258470 86004800 86006720 86028630 86271280 PRV NO.
CIRCUIT BREAKER GROUP 3 2 1 4 5-3 GLIDE 86037550 01/09/07
CIRCUIT BREAKER GROUP REF PART NO. PRV NO. QTY DESCRIPTION 1 86273990 70067 4/6 SCR, 6-32 X 3/8 PPHMS 2 86279300 87134 4/6 WASHER, #6 LOCK 3 86001920 14607 4 86008900 80845 2/3 BREAKER, 25A 50VDC CIRCUIT BOOT, SEAL-PUSH BUTTON 7/162/3 28 GLIDE 86037550 01/09/07 SERIAL NO.
CONTROL PANEL GROUP 1 2 6 3 8 4 25 7 24 1 22 23 26 5 5 27 20 28 29 17 19 18 16A 16B 16C 16D 10 15 30 11 9 13 14 12 5-5 GLIDE 86037550 01/09/07
CONTROL PANEL GROUP REF 1 2 3A 3B 4 5 6 7 8 9 10 11 12 13 14 15 16A 16B PART NO. 86270920 86005550 86007190 86004860 86007180 86257280 86271820 86238000 86093320 86270990 86276900 86003230 86276890 86271910 86010670 86068850 86002660 86002670 PRV NO.
DECAL GROUP 2 4 8 9 7 6 3 1 5A 5B 5-7 GLIDE 86037550 01/09/07
DECAL GROUP REF 1 2 3 4 5A 5B 6 7 8 9 PART NO. 86004970 86243510 86243570 86243500 86244130 86244140 86248210 86243580 86243810 86243820 PRV NO. 50990 500563 500574 500562 500859 500861 81349 500575 500651 500662 QTY 1 1 2 1 1 1 1 1 1 1 DESCRIPTION LABEL, WINDSOR LOGO DOMED LABEL, CONTROL PANEL LABEL, GLIDE LABEL, SRS CHARGING LABEL, GLIDE TRIO + CB LABEL, GLIDE 36 TRIO + CB OVERLAY, HORN LABEL, SOLUTION FILL GLIDE LABEL, DECK SHIFT 36 INCH LABEL, COVER SMALL RIDER SERIAL NO.
FRONT BUMPER & FLOOR GROUP 2 4 3 3 1 5 6 7 5-9 GLIDE 86037550 01/09/07
FRONT BUMPER & FLOOR GROUP REF 1 2 3 4 5 6 7 PART NO. 86248350 86276780 86010670 86276910 86082320 86031840 86248360 PRV NO. 66360 70728 87029 70754 62952 27958 66361 QTY 1 2 7 5 1 1 1 DESCRIPTION PAD, FLOOR SCR, 5/16-18 X 3/4 HHCS SS WASHER, 5/16 FLAT SS SCR, 5/16-18 X 3 HHCS SS NP PLATE, FLOOR COVER, BUMPER DK GRY PAD, STEP GLIDE 86037550 01/09/07 SERIAL NO.
FORWARD/REVERSE PEDAL 6 3 5 1 1 4 2 7 10 8 9 12 13 14 8 15 11 16 13 17 16 1 5-11 GLIDE 86037550 01/09/07
FORWARD/REVERSE PEDAL REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86005810 86007380 86078310 86273850 86276940 86248340 86006330 86276930 86093140 86278060 86089660 86091500 86228750 86273780 86010300 86010290 86010680 PRV NO. 57245 730088 66382 70022 70758 66346 66343 70757 51379 70759 78532 140577 09082 70015 830117 830116 87030 QTY 3 1 1 1 1 1 1 2 1 2 1 1 2 1 1 3 2 DESCRIPTION NUT, 1/4-20 HEX NYLOCK SS SPACER, .50D X .26ID X 1.5L PEDAL, SMALL RIDER SCR, 1/4-20 X 2 HHCS SCR, 1/4-20 X 3.
SCRUB BRUSH/PAD DRIVER 7 5 6 9 4 8 7 5 6 9 4 8 1 5 3 5-13 GLIDE 86037550 01/0907 2A 2B 2C 2D
SCRUB BRUSH/PAD DRIVER 28 IN. DISK: REF 1 2A 2B 2C 2D PART NO. 86000250 86000260 86000270 86000280 86283850 PRV NO.
SCRUB DECK GROUP 1 FROM SOLUTION STRAINER 20 26 23 27 22 5 3 28 24 6 29 19 4 31 21 17 18 25 30 29 15 16 11 7 5 23 8 9 14 17 10 13 12 5-15 GLIDE 86037550 01/09/07 2
SCRUB DECK GROUP REF 1 1A 2 3 4 5 6 7 PART NO. 86005250 86001890 86279130 86087940 86253910 86276950 86093960 86276970 PRV NO.
SCRUB DECK SIDE SQUEEGEE GROUP 1 2 14 21 3 4 6 19 22 8 7 20 23 16 5 9 13 17 15 18 12 11 5 4 10 5-17 GLIDE 86037550 01/09/07
SCRUB DECK SIDE SQUEEGEE GROUP REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86094220 86082160 86226830 86007020 86010670 86094230 86005810 86007420 86276960 86087920 86276900 86279380 86082170 86272580 86228840 86270830 86065960 PRV NO.
SCRUB DECK LIFT GROUP 25 21 16 18 22 26 18 1 2 23 24 3 4 5 6 3 7 15 17 5 21 14 15 8 14 17 9 6 18 20 11 16 18 12 13 10 19 17 15 14 3 5-19 GLIDE 86037550 01/09/07 5
SCRUB DECK LIFT GROUP REF 1 2 3 4 5 6 7 PART NO. 86272600 86352950 86008670 86092250 86008720 86090270 86077470 PRV NO.
SCRUB DECK -32 IN 1 FROM SOLUTION STRAINER 20 26 23 27 24 5 3 22 29 4 28 29 29 6 21 25 19 15 30 16 5 29 17 23 11 7 8 9 14 10 13 12 5-21 GLIDE 86037550 01/09/07 18
SCRUB DECK –32 IN REF 1 1A 2 3 4 5 6 7 PART NO. 86005250 86001890 86273810 86087950 86253950 86276950 86093980 86276970 PRV NO.
SCRUB DECK SIDE SQUEEGEE –32 IN 9 22 25 7 24 23 26 7 14 21 3 4 1 2 6 27 28 7 29 32 33 31 30 16 5 13 18 12 8 7 19 20 9 15 5 4 11 10 5-23 GLIDE 86037550 01/09/07
SCRUB DECK SIDE SQUEEGEE –32 IN REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86094220 86086840 86226830 86007020 86010670 86094230 86005810 86007420 86276320 86087920 86276900 86279380 86082170 86272580 86228840 86270830 86065960 PRV NO.
SCRUB DECK-36 IN MAIN FROM SOLENOID VALVE 3 6 18 1 36 13 17 14 9 4 8 15 35 38 34 33 10 11 17 12 16 12 37 11 19 12 26 23 24 25 32 2 20 7 26 26 21 22 31 23 26 30 29 28 27 5-25 GLIDE 86037550 01/09/07
SCRUB DECK-36 IN MAIN REF 1 2 3 4 5 5A 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 PART NO. 86276910 86001550 86273960 86000840 86005250 86001890 86223470 86271830 86253250 86272620 86007570 86256500 86270830 86236170 86197910 86033220 86264920 86281410 86281480 86009200 86274110 86010790 86276970 86276950 86007410 86087900 86005810 86007020 86279130 86279630 86003420 86279530 86093970 86087280 86008650 86087290 86082570 86070300 86276780 PRV NO.
SCRUB DECK-36 IN RETRACTABLE 12 9 2 1 5 3 2 6 4 5 32 FROM SOLUTION MANIFOLD 7 30 31 21 18 29 19 28 33 20 8 27 10 11 19 26 25 14 24 10 13 21 15 16 23 22 5-27 GLIDE 86037550 01/09/07 17
SCRUB DECK-36 IN RETRACTABLE REF 1 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PART NO. 86005250 86001890 86009550 86093020 86009520 86228930 86281440 86001550 86277860 86264920 86010770 86279620 86007670 86278130 86069540 86007400 86087910 86276950 86010890 86005810 86271830 86005630 86276970 86010790 86007020 86279130 PRV NO.
SCRUB DECK SIDE SQUEEGEE-36 IN 3 2 4 1 5 14 6 15 16 7 17 8 1 9 11 21 13 12 14 31 15 16 17 27 28 30 11 24 29 22 26 24 23 25 27 24 23 22 10 18 4 20 19 5-29 GLIDE 86037550 01/09/07 9
SCRUB DECK SIDE SQUEEGEE-36 IN REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO. 86005630 86010890 86274010 86005810 86087860 86276780 86007550 86069580 86276960 86083740 86270830 86082220 86065960 86277090 86242120 86005650 86226810 86277120 86087890 86007390 86083730 PRV NO.
SCRUB DECK LIFT-36 IN 24 28 1 16 30 22 25 8 7 23 2 3 4 5 7 29 33 FROM SOLUTION STRAINER 34 32 9 8 27 21 13 16 18 10 11 12 17 26 17 14 15 15 14 17 5-31 18 20 GLIDE 86037550 01/09/07 18 31 15 30 19
SCRUB DECK LIFT-36 IN REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 PART NO. 86008720 86014490 86277860 86275960 86091720 86093970 86270830 86270880 86001320 86005830 86006440 86005800 86008810 86276920 86008460 86271530 86009050 86005630 86077330 86066780 86009710 86003460 86004620 86276780 86008550 86005740 86008740 86273780 86005810 86008670 86255430 86274010 86254250 86233150 86282060 86010730 PRV NO.
SEAT & SIDE COVER 1 9 10 2 3 14 23 16 15 19 14 24 22 20 9 7 18 6 21 4 19 4 11 9 7 12 8 17 15 5 14 7 5 7 14 13 5-33 GLIDE 86037550 01/09/07
SEAT & SIDE COVER REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO. 86253150 86257070 86006580 86276890 86276780 86271240 86010670 86239640 86006560 86279650 86069700 86279630 86288400 86270830 86233440 86069710 86086550 86282780 86279380 86008460 86093760 86238470 86093750 86277040 PRV NO.
SOLUTION DELIVERY 1 3 4 5 6 7 8 9 12 10 13 2 15 14 11 TO SOLENOID VALVE 5-35 GLIDE 86037550 01/09/07
SOLUTION DELIVERY REF 1 2 3 4 5 6 7 8 9 10 11 12 13 13A 13B 14 PART NO. 86273780 86198050 86076820 86005810 86282150 86236180 86233300 86240150 86233110 86240330 86233150 86247760 86256040 86007250 86005870 86197910 PRV NO.
SQUEEGEE – 28 IN & 36 IN 37 30 32 31 29 5 6 19 7 28 24 13 27 34 9 28 29 33 1 26 25 11 22 23 3 2 12 10 36 21 15 16 17 9 14 18 8 4 35A 35B 5-37 GLIDE 86037550 01/09/07 20A 20B
SQUEEGEE –28 IN & 36 IN REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20A 20B 20C 20D 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35A 35B 36 37 PART NO.
SQUEEGEE 32-IN 34 25 8 16 14 30 14 35 35 31 32 10 17 13 22 2 27 12 33 28 11 4 26 5 24 18 29 23 19A-19D 20 33 15 6 21 7 3 9 1 5-39 GLIDE 86037550 04/11/11
SQUEEGEE-32 IN REF PART NO.
SQUEEGEE LIFT 7 4 6 8 5 15 5 1 14 2 16 3 DETAIL 'A' 4 8 13 SEE DETAIL 'A' 9 32" MODEL 28", 36" MODELS 11 2 10 5-41 GLIDE 86037550 01/09/07
SQUEEGEE LIFT REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 86277860 86010770 86010160 86008870 86008860 86000810 86248910 86008670 86255310 86272710 86091710 86005630 86009860 86088270 86010050 86271980 PRV NO. 70787 87143 82830 80815 80808 05167 66369 80606 73979 82060 140473 57022 82541 730121 82696 57303 QTY 1 3 1 4 2 1 1 3 2 1 1 1 1 1 1 1 DESCRIPTION SCR, 3/8-16 X 3.75 HHCS SS WASHER, 7/16ID X 1D X .08 FLT SS SPRING, .62 X .09 X 1.
STEERING-UPPER 1 2 3 4 5 6A 6B 18 7 9 17 13 11 10 8 16 12 14 15 5-43 GLIDE 86037550 01/09/07
STEERING-UPPER REF 1 2 3 4 PART NO. 86234810 86271610 86259610 86253230 PRV NO.
STEERING- LOWER 2 6 16 21 15 20 18 19 8 7 5 1 17 11 13 9 14 10 12 4 10 3 9 8 5-45 GLIDE 86037550 01/09/07
STEERING- LOWER REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO. 86276970 86258330 86232800 86082310 86082840 86288410 86005810 86005860 86270310 86264490 86002850 86278070 86094330 86087260 86276780 86228790 86270830 86001030 86008610 86272900 86005610 PRV NO.
TANK 1 2 3 6 7 8 4 9 5 15 23 26 2 10 25 24 2 11 12 13 12 17 14 16 17 18 (TORQUE 50 IN-LBS MAXIMUM) 19 2 22 20 21 5-47 GLIDE 86037550 01/09/07
TANK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART NO. 86235580 86233430 86033270 86276600 86066310 86273950 86234790 86246080 86270920 86032570 86279630 86276780 86237790 86006260 86006340 86033140 86010670 86007020 86033290 86234900 86004420 86240450 86076830 86002830 86004410 86008400 PRV NO.
TANK COVER 1 22 2 3 21 4 20 5 5 19 6 7 17 16 18 8 15 9 10 11 7 12 14 13 5-49 GLIDE 86037550 01/09/07
TANK COVER REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO. 86273950 86246080 86270920 86276910 86279630 86198450 86006500 86003690 86069740 86010670 86277040 86007460 86082360 86264930 86271850 86233560 86258670 86238010 86031830 86276790 86004010 86003340 PRV NO.
VACUUM GROUP 8 3 9 1 10 6 2 4 7 5 8 11 13 12 5-51 GLIDE 86037550 01/09/07
VACUUM GROUP REF 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. 86274800 86069560 86003010 86279130 86276780 86005810 86005450 86230800 86135310 86233140 86240170 86264920 86091170 86233430 86064910 PRV NO. 70297 140476 27759 87083 70728 57245 53799 140550 140686 20041 39614 27049 730174 81431 54194 QTY 3 1 1 2 2 6 1 1 1 2 1 3 1 1 1 DESCRIPTION SCR, 1/4-20 X 1.5 HHMS BRACKET, VACUUM MOUNTING CUFF, HOSE 1.
WHEELS & FRAME 1 2 6 7 14 11 5 3 4 12 8 8B 8F 16 9 13 10 (TORQUE 8-10 FT-LBS) 5-53 GLIDE 86037550 11/05/08 15 (TORQUE 23-28 FT-LBS)
WHEELS & FRAME REF PART NO. PRV NO. QTY 1 86238500 81427 2 3 4 86092430 86232130 86272910 34385 17309 67471 5A 86011090 89224 5B 6 7 8 86259890 86276920 86010790 86003450 89230 70755 87163 29256 DESCRIPTION GROMMET, 1.703ID X 2.5OD X .125 3 GRY 1 FRAME, RIDER SCRUBBER 2 CAP, 2.75 ID X 1.0 L BLK VINYL 2 RING, 63/64 EXTERNAL SNAP WHEEL ASM, 12 X 3.5 X 8 SCRUBBER 2 COMPOUND REF WHEEL ASM, 12 X 3.5 X 8 GRAY 4 SCR, 3/8-16 X 1 HHCS SS NP 4 WASHER, 3/8 SPLIT LOCK 1 MOTOR ASM, 36V DRV.
WIRING-BATTERY 1 27 4 12 15 2 5 3 6 7 28 8 10 26 9 12 13 1 14A 11 14B 24A 24B 15 23A 23B 25 22 20 21 16 17 18 7 19 5 5-55 GLIDE 86037550 06/03/11
WIRING-BATTERY REF PART NO. PRV NO.
WIRING GROUP-MAIN HARNESS A B C D E DIAGRAM A COM 22 6 76 RED BRAKE SWITCH NO 35A BRUSH 34A BLU 21 RED 75 BLK 33A ORG 2, 3, 4 DIAGRAM B 68 YLW 70 RED 69A BLK SOLENOID VALVE 5A LT-BLU VACUUM 6C WHT-YLW 5 ACTUATOR 71 BLK 76C RED 80 RED 77A BLK 75B BLK BRUSH MOTOR 3 81 BLK 74 RED BRUSH MOTOR 1 DIAGRAM C BRUSH MOTOR 2 POSITIVE BATT CABLE NEGATIVE BATT CABLE 22A RED 5 LTBLU 3 WHT-BLK 14A GRY 70C RED 71C BLK 21A RED 2, 3, 4 6 WHT-YLW VAC MOTOR 1 67 ORG 69 BLK 19A GRY 86A
WIRING GROUP - MAIN HARNESS REF 1 2 3 4 5 6 PART NO. 86239500 86233390 86273780 86005810 86264920 86239510 PRV NO. 880421 80887 70015 57245 27049 880422 QTY 1 2 2 2 2 REF DESCRIPTION HARNESS, SRS UPPER CLAMP, 7/8 DIA “P” CUSHIONED SCR, 1/4-20 X 3/4 HHCS SS NUT, 1/4-20 HEX NYLOCK SS CABLE TIE, 7” UL/CSA LCD HARNESS GLIDE 86037550 01/09/07 SERIAL NO.
WIRING GROUP - MAIN HARNESS CONNECTION 100A RED LCD 2A G F 100B RED 6 1 24 ORG 1 HORN 25A ORG RECYCLE LIGHT 64A RED HEAD LIGHT 67B RED 30A RED 7A BLK KEY SWITCH 101A BLK 84A BLK FUSE HOLDER 101B BLK 32 RED 85 BLK 80 RED BLK 77 76D RED 66C RED 25A 25A 25A 76B RED 82 RED 83 RED 2 DIAGRAM D D 6 WHT-YLW 5 LTBLU 3 WHT-BLK 3 WHT 67 ORG 4 WHT-ORG 68 YLW 66 RED C 69 BLK 16 WHT E DIAGRAM C DIAGRAM G VACUUM 19 GRY 64 RED 33 ORG 65 BLU BRUSH 7 BLK 16 WHT 22 RED 14 ORG 3
WIRING GROUP-MAIN HARNESS CONNECTION REF 1 2 3 4 5 6 PART NO. 86239500 86267290 86260310 86232040 86239010 86239510 PRV NO. 880421 880262 82687 830957 41462 880422 QTY REF 1 REF REF 1 1 DESCRIPTION HARNESS SRS UPPER WIRE, 14” GRN/18 76008 X 76011 WIRE, 4 X 77BK C. TERM X 5/16 RING CABLE, 4GA BLACK X 78.5” HARNESS, DECK SHIFT LCD HARNESS SERIAL NO. FROM NOTES: 36 IN ONLY NOTE: Maximum speed of machine can be decreased to 80% of maximum by disconnecting wire 3 white from wire 16 white.
WIRING GROUP-CONTROL PANEL GROUP 33 ORG 22 RED 34 LT BLU 35 RED 36 RED LCD 2 E STOP 32A RED 31A WHT 28A BLU 27A ORG 26A BLK 29A GRN 30 RED 3 1 WHT/BLU 2 BLK 3 LTBLU 4 LTBLU 7 YLW 8 GRN 10 LTBLU 11 WHT 1 12 LTBLU 15 ORG 16 BLU 12B LTBLU 12A LTBLU 4A LTBLU 4B LTBLU 16 LTBLU 16 LTBLU ONE TOUCH DISPLAY TOGGLE 16 BLU 16 BLU 16 BLU 15A ORG 2A BLK 7A YLW 16 LTBLU 16 BLU 16 LTBLU 16 BLU 11A WHT 8A GRN 1A WHT-BLU VACUUM/SQUEEGEE SOLUTION CONTROL BRUSH PRESSURE 35A RED 30A RED 32 RED 1
WIRING GROUP-CONTROL PANEL REF 1 2 3 PART NO. 86239490 86239500 86239510 PRV NO. 880378 880421 880422 QTY DESCRIPTION 1 HARNESS, CONTROL REF HARNESS, GLIDE TRIO + REF HARNESS, GLIDE LCD GLIDE 86037550 01/09/07 SERIAL NO.
WIRING-DRIVE MOTOR 1 2 5-63 GLIDE 86037550 01/09/07
WIRING -DRIVE MOTOR REF 1 PART NO. 86010870 PRV NO. 880379 2 86261660 880424 QTY DESCRIPTION 1 HARNESS, PROPEL 1 WIRE HARNESS, FCM GLIDE GLIDE 86037550 01/09/06 SERIAL NO.
WIRING DIAGRAM 1 WHT/BLU 2 BLK 10 LTBLU 3 LTBLU 11 WHT 4 LTBLU 7 YLW 16 LTBLU 16 BLU 8 GRN 11A WHT 7 BLK 19 GRY 65 BLU 90 WHT 89 WHT 14 GRY 67 ORG 66 RED 68 YLW 4 WHT-ORG 3 WHT-BLK CONTROLLER 64 RED 69 YLW 3 LTBLU 1A WHT-BLU 15 ORG 5 LT-BLU 6 WHT-YLW 28 BLU 31 WHT 27 ORG 30 RED 26 BLK 29 GRN 125 AMP 5-65 36v GLIDE 86037550 01/09/07 16 BLU 2A BLK 16 BLU 7A YLW 4 LTBLU 16 BLU 10 LTBLU INFO 12 LTBLU 16 BLU 8 GRN 15 ORG 16 LTBLU 32A RED 31A WHT LCD 16 LTBLU 29A GRN 27A OR
SUGGESTED SPARE PARTS PART NO. 86008790 86001870 86001440 86003690 86007420 86007580 86007390 86007550 86004860 86005450 86230800 86135310 86001460 86001890 86009200 86215180 86002850 86007380 86005610 86007460 86001920 86002010 86008900 86004420 86002030 86007250 86135480 86010330 86006340 PRV NO. 80687 14415 140533 34390 730100 730167 730093 730154 48073 53799 140550 140686 140552 14418 81535 09142 27343 730088 57016 730122 14607 14942 80845 39609 17298 730000 83052 83053 66347 DESCRIPTION SERIAL NO.
ACCESSORY PUMP-OPTION 3 4 7 11 15 5 8 2 1 9 2 10 12 13 14 15 16 1 5-67 2 6 GLIDE 86037550 01/09/07
ACCESSORY PUMP-OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 86282170 86233150 86197550 86081820 86005580 86240410 86273810 86197940 86006100 86001550 86281520 86226900 86233370 86069980 86005810 86281000 PRV NO.
BACK-UP ALARM-OPTION 2 1 5-69 5 3 4 GLIDE 86037550 01/09/07
BACK-UP ALARM-OPTION REF 1 2 3 4 5 PART NO. 86005720 86005810 86273750 86227260 86010630 PRV NO. 57106 57245 70011 82332 87013 QTY 2 2 2 1 2 DESCRIPTION NUT, 8-32 W/ STAR WASHER PLTD NUT, 1/4-20 HEX NYLOCK SS SCR, 1/4-20 X 5/8 HHCS SS NP ALARM, BACK UP WASHER, 1/4 ID X 5/8 OD SS GLIDE 86037550 01/09/07 SERIAL NO.
DUAL VACUUM MOTOR-OPTION 10 8 11 1 12 2 9 1 7 6 5 4 3 1 5-71 GLIDE 86037550 01/09/07
DUAL VACUUM MOTOR-OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 PART NO. 86233140 86076840 86004370 86007770 86276370 86005450 86230800 86135310 86005620 86235780 86003750 86010780 86273830 86076800 PRV NO. 20041 40092 39547 73566 70638 53799 140550 140686 57021 34164 35122 87162 70020 39612 QTY 4 1 1 3 3 1 1 1 3 1 1 3 3 1 DESCRIPTION CLAMP, 2.0” WORM GEAR HOSEBARB, 1.50 TEE MACHINED HOSE ASM, 1.5 BLK VAC X 21 SPACER, 1/2 OD X 3.0 W/1/4-20 AL SCR, 1/4-20 X 1.
WARNING LIGHT-OPTION 1 3 2 4 5 5-73 GLIDE 86037550 01/09/07
WARNING LIGHT-OPTION REF 1 2 3 4 5 PART NO. 86025990 86276600 86264950 86275730 86069970 PRV NO. 51286 70696 27746 70534 140555 QTY 1 3 5 3 1 DESCRIPTION LIGHT ASM, FLASHING 36V AMBER SCR, #10 X 3/4 PTHSMS SS CABLE TIE, .19W X 11.5L BLK SCR, 1/4-14 X 3/4 TEKS/3 HWHS PLTD BRKT, LIGHT MOUNT GLIDE 86037550 01/09/07 SERIAL NO.
5-75 GLIDE 86037550 01/09/07
GLIDE 86037550 01/09/07 5-76
5-77 GLIDE 86037550 01/09/07
SERIAL NUMBERS REF. NO.