www.windsterhood.com UNDER CABINET SERIES WALL MOUNT SERIES User s Manual WS-3230SS WS-3236SS WS-3242SS WS-3248SS NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON RECEIVING. CLAIM OF DAMAGE AFTER 7 DAYS OF DELIVERY WILL BE DENIED. This unit is designed for indoor residential use only. DO NOT USE OVER A WOOD GRILL OR MOUNT IN OUTDOOR ENVIRONMENT. Please read this operation manual thoroughly before using your range hood. Store it in a safe location for when you need to reference it in the future.
TABLE OF CONTENTS 1 Table of Contents Safety Information ............................................................... 2 - 3 Content Checklist ..................................................................... 4 Measurements ........................................................................... 5 Preparation ........................................................................... 6 - 7 Installation .................................................................................
2 SAFETY INFORMATION SAFETY INFORMATION "CAUTION-To reduce risk of fire, properly exhaust air according to local city building code(s). "WARNING-To reduce the risk of fire or electric shock, do not use this fan with any solid- state speed control device.
SAFETY INFORMATION 3 D. Use an extinguisher ONLY if: 1. You know you have a Class ABC extinguisher, and you already know how to operate it. 2. The fire is small and contained in the area where it started. 3. The fire department is being called. 4. You can fight the fire with your back to an exit. WARNING-TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY OBSERVE THE FOLLOWING: a) Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
4 CONTENT CHECKLIST CONTENT CHECKLIST 1. CONTENTS INCLUDED a. (1) WS32 series(30" , 36" , 42" or 48")hood assembly b. (1) User’s manual c. (1) 7" conversion collar d. (2) Aluminum filters with frame & (2) stainless steel filler (30") e. (2) Aluminum filters with frame & (2) stainless steel filler (36") f. (3) Aluminum filters with frame & (2) stainless steel filler (42") g. (3) Aluminum filters with frame & (2) stainless steel filler (48") h. (2) Stainless steel oil trays (30" and 36") I.
MEASUREMENTS 5 15/16" Fig.1a 12" 2-1/4" 8-1/4" 10-7/8" 30" (14-7/8") 36" (17-7/8") (side to duct center) 42" (20-7/8") 48" (23-7/8") 9/16" (back to duct edge) (back to duct center) power cable 1" x 1-1/2"(30") 1" x 2-1/2"(36"-48") 4-1/8" 3" 2-1/2" 8-3/8" 7-7/8" 30" (29-3/4") 36" (35-3/4") 42" (41-3/4") 48" (47-3/4") 24" Fig.
6 PREPARATION PREPARATION 1. BEFORE YOU START **DO NOT INSTALL IF DAMAGED** **RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED** a. Be sure you have all the content of your purchase and required tools for this installation. b. Installation may take at least 1 to 2 hours from start to finish. c. Plan to use as few elbows or turns as possible for more efficient air flow. d. Collar size may need to be increased if utilizing a long duct run. e. At least 12" of vertical duct is required before any turn. f.
PREPARATION 7 Fig. 1c - Cabinet FRONT OF CABINET 11 (30" CABINET) 14 (36" CABINET) 17 (42" CABINET) 20 (48" CABINET) CABINET SIDE CABINET SIDE CABINET BOTTOM VIEW 7.5-8" ROUND EXHAUST ELECTRICAL OUTLET ½" BACK OF CABINET e. For cabinet with recessed-bottom, use (2) 3" x 12" or 15" wood strips on both sides to balance the recession. Use (4) 1-1/4" long flat head screws to secure the wood strips to cabinet. (Fig. 1d) Fig.
8 INSTALLATION INSTALLATION UNDER CABINET INSTALLATION (Top round outlet) a. Make sure all preparation steps are completed. b. Feed the wires coming out of the hood through the bottom of the cabinet. c. Lift the unit up flesh against the wall and the bottom of the cabinet. d. Using the screws and washers provided, insert into each of the keyhole openings and tightly secure the unit against the bottom of the cabinet. NOTE: Install more screws through the back of the unit if necessary. e.
9 3. REMOVING THE FILTERS Aluminum Filter Set Baffle Filter (Optional) a. Pull up on the filter latch, tilt towards you and remove the filter. a. i Push the handles back/down into the hood and. ii Tilt the filters towards you. ii i b. i Push the frame back/down into the hood. ii Tilt the frame out. b. iii Remove the baffle filter. ii iii i c. iii Remove the frame. c. Remove stainless steel oil tray for cleaning.
10 CLEANING& MAINTENANCE WARNING!!! To prevent the possibility of a fire and explosion, do not use flammable liquids or solvents to clean the unit or any of its parts. Check to make sure all power sources are disconnected before servicing or taking unit apart for cleaning. Please thoroughly clean the unit weekly as stainless steel can rust under certain condition or by improper cleaning. 1. RANGE HOOD a. Use household cleaner to remove grease or dirt from the outer shell of the unit.
TROUBLESHOOTING 11 TROUBLESHOOTING WARNING!!! Check to make sure all power sources are disconnected before starting any troubleshooting. Safety gloves and glasses should be worn when working on the unit. Serious injury or death may occur if safety precautions are not followed. WS-32 Series Light Issue (One light not turning on) 1. Replace defective fixture with new fixture. Burnt/melted control switch 1. Complete Control switch replacement is required. Speed levels not working correctly 1.
12 PART LIST / REPLACEMENT PART LIST / REPLACEMENT 13 17 14 15 16 3 1 6 2 4 5 11 7 8 12 9 10 # Description # Description 1 Hood body assembly 10 Filter frame 2 Right Motor 11 Aluminum filter 3 Left Motor 12 Stainless steel oil tray 4 Stainless steel filler 13 Electronic cover 5 Right Fan 14 Control switch mount 6 Left Fan 15 Main board 7 Fan Cover 16 Main board bracket 8 Oil Tunnel 17 Light set (GU10) 9 Oil Tunnel Mount
WARRANTY / CONTACT US 13 WARRANTY / CONTACT US LIMITED WARRANTY Windster Hoods Inc. warrants its product against defects in material or workmanship as follows: Labor: For a period of one (1) year from the date of purchase, if the product is determined to be defective, Windster will attempt to repair the product, at its option, at no charge. After the warranty period, customer must pay for all labor charges.
14 WARRANTY / CONTACT US WHAT IS NOT COVERED BY MANUFACTURE WARRANTY 1. Damages resulting from any of the following: a. Improper installation or maintenance b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized service dealer c. Misuse and/or accidents d. Incorrect electric current, voltage or power supply e. Improper setting of any control (Pressing multiple selections at the f.