- www.windsterhood.com User’s Manual ISLAND SERIES HI30SS HI36SS HI42SS NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON RECEIVING. CLAIM OF DAMAGE AFTER 7 DAYS OF DELIVERY WILL BE DENIED. This unit was designed for indoor residential use only. DO NOT USE OVER A WOOD GRILL OR MOUNT IN OUTDOOR ENVIRONMENT. Please read this operation manual thoroughly before using your range hood. Store it in a safe location for when you need to reference it in the future.
TABLE OF CONTENTS 1 Table of Contents Safety Information .............................................................. 2 – 3 Content Checklist ..................................................................... 4 Measurements ........................................................................... 5 Preparation ................................................................................ 6 Installation ...........................................................................
2 SAFETY INFORMATION SAFETY INFORMATION TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK, AND/OR INJURY OBSERVE THE FOLLOWING: Unit is intended for indoor residential use only. If you should have questions, contact the manufacturer at the address or telephone number listed in the warranty. In case the unit should need to be cleaned or repaired, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally.
SAFETY INFORMATION 3 TO REDUCE THE RISK OF FIRE, OR ELECTRIC SHOCK, DO NOT . USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. Regardless of heat level, never leave any surface materials unattended while operating an open flame. Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé). Depending on amount of usage, clean ventilating fans and filters frequently.
4 CONTENT CHECKLIST CONTENT CHECKLIST 1. CONTENTS INCLUDED a. (1) HI series range hood assembly (30‖, 36‖ or 42‖) b. (1) Lower duct cover (16-1/2‖) c. (1) Upper duct cover (22-3/4‖) d. (1) User’s manual e. (1) 7‖ Damper transition adapter collar f. (1) Stainless Steel Baffle Filter (30‖ model) g. (2) Stainless Steel Baffle Filters (36‖/42‖ model) h. (1) Mounting packet i. (1) Duct cover support bracket 2. OPTIONAL ACCESSORIES NOT INCLUDED a. HILDC (Long duct cover) b.
MEASUREMENTS 28" 5
6 PREPARATION PREPARATION 1. BEFORE YOU START **BE SURE YOUR UNIT WILL FIT YOUR CEILING HEIGHT** **DO NOT INSTALL IF DAMAGED** **RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED** a. Be sure you have all the content of your purchase and required tools for this installation. b. Installation may take at least 2 to 3 hours from start to finish. c. For more efficient air flow limit the amount of elbows or turns used in the duct work. d. Collar size may need to be increased if utilizing a long duct run.
INSTALLATION 7 INSTALLATION 1. STANDARD INSTALLATION a. Make sure all preparation steps are completed. b. Determine your ceiling height to verify if you will require an extension.. i. Unit height from edge of glass = 3-1/4‖ (30‖ model only) ii. iii. Unit height from edge of glass = 4-1/4‖ (36‖ model only) Unit height from edge of glass = 6‖ (42‖ model only) iv. Standard DC height = 16-1/2‖ (lower) + 22-7/8‖ (upper w/ luvers) v. Minimum height (Standard duct cover only) = 24-3/4‖ vi.
8 INSTALLATION 2. EXTENSION INSTALLATION (OPTIONAL) a. AFTER COMPLETING STEP A – D OF STANDARD INSTALLATION, replace the standard support frame and duct cover with either the extension set or the short duct cover set. b. REPEAT “STEP F – M” from STANDARD INSTALLATION. 3. DUCTLESS INSTALLATION (OPTIONAL) a. AFTER COMPLETING Step A – E of STANDARD INSTALLATION b. Remove the HIDK (ductless kit) and inspect for any sign of defect or damage. (ie. dents, broken inlet) c.
OPERATION & FEATURES INSTALLATION DIAGRAM 9
OPERATION & FEATURES 10 OPERATION & FEATURES 1. EASY ACCESS CONTROL SWITCH (from left to right) a. Button 1 – ON / OFF b. Button 2 – Low Speed c. Button 3 – Medium Speed d. Button 4 – High Speed e. Button 5 – Light Switch 2. STAINLESS STEEL BAFFLE FILTERS a. (1) Stainless steel baffle filter (30‖ model) b. (2) Stainless steel baffle filters (36‖ / 42‖ model) 3. CHARCOAL FILTERS **DO NOT WASH CHARCOAL FILTERS! IT WILL DISSOLVE!!** a. Replace safety filter with charcoal filter. (Fig. 3a) b.
CLEANING & MAINTENANCE 11 CLEANING & MAINTENANCE .WARNING!!!. To prevent the possibility of a fire and explosion, do not use flammable liquids or solvents to clean the unit or any of its parts. Check to make sure all power sources are disconnected before servicing or taking unit apart for cleaning. Please thoroughly clean the unit weekly as stainless steel can rust under certain condition or by improper cleaning. 1. RANGE HOOD a.
12 TROUBLESHOOTING TROUBLESHOOTING WARNING!!! Check to make sure all power sources are disconnected before starting any troubleshooting. Safety gloves and glasses should be worn when working on the unit. Serious injury or death may occur if safety precautions are not followed. HI Series Light issue LED (All not turning on) 1. Locate and Replace defective Fixture (All Fixtures run on same circuit). 2. New Transformer/ Driver replacement may be required Speed Levels/Controls not working correctly 1.
PART LIST / REPLACEMENT/ WIRING DIAGRAM 13 PART LIST / REPLACEMENT # Description # Description 1 2 3 4 Chimney Supporting Frames Duct cover Hood body assembly LED lights Control switch 6 7 8 9 Transformer Capacitor Transition collar Squirrel cage motor 10 Baffle filter 5 WIRING DIAGRAM
WARRANTY / CONTACT US 14 WARRANTY / CONTACT US LIMITED WARRANTY Windster Hoods Inc. warrants its product against defects in material or workmanship as follows: Parts: Windster Hoods, Inc. will supply, at no charge, new or rebuilt replacements in exchange for defective parts for a period of two (2) years. After the warranty period, you must pay for all parts costs. During the "parts" warranty period, there will be no charge for parts Motor: Windster Hoods, Inc.
WARRANTY / CONTACT US 15 *Windster Hoods, Inc. reserves the right to determine the validity of your warranty claim. WHAT IS NOT COVERED BY MANUFACTURER WARRANTY 1. Damages resulting from any of the following: a. Improper installation or maintenance b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized service dealer c. Misuse, accidents, and/or neglect d. Incorrect electric current, voltage or power supply e.