OPERATION MANUAL ? SPEEDS : 3 ? LED Light R-33L Series R-34L Series R-35L Series Please read and save this guide through before using your range hood Store the guide away in a safe place so that you will know where it is when you want to refer to it
Table of Contents A. Important Safety Instructions B. Safety Notes C. To o l s a n d M a t e r i a l s R e q u i r e d D. Ducting E. Preparing the Range Hood F. Preparing the Installation Location -------------------------------------------------------------- P.3 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P.4 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P.4 G.
A. Important Safety Insturctions Read and Save These Instructions CAUTION- To reduce risk of fire and to properly exhaust air, make sure to properly exhaust air. Be sure to duct air outside- Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or garages. WARNING- To reduce the risk of fire or electric shock, do not use this fan with any solid- state speed control device. WARNING- TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY, OBSERVE THE FOLLOWING: A.
WARNING- To reduce the risk of injury in the event of a range top grease fire, observe the following: A- SMOTHER FLAMES with a close- fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful to prevent burns. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. B- NEVER PICK UP A FLAMING PAN - You may be burned. C- DO NOT USE WATER including wet dishcloths or towelsa violent steam explosion will result. D- USE AN EXTINGUISHER ONLY IF: 1.
B. Safety Notes 1. All electrical work must be done in accordance with local and/or national electrical code as applicable for safety. This product must be grounded if your are unfamiliar with methods of installing electrical wiring, secure the services of a qualified electrician. 2. Turn off power at service entrance before installing wiring or servicing this product. (120 volt for range hood. 220 volt for electric range if any) 3.
C. Tools and Materials Required Drill, electric of ratchet drive, with 3/16" wood bit (for drilling starter holes and 1 ¼ ” wood bit (to drill an access holes in the cabinet or kitchen wall for the electric power line) One common screwdriver. Plier (for opening electrical knockout). Two 1" (thick)x2" (wide)x12" (approximate length) wood strips for recessed bottom kitchen cabinet installation only. (Purchase locally). Electrical wire and supplies to comply with local cords.
E. Preparing The Range Hood 1. Remove the top electrical Electrical Knockout knockout, you may plan to bring power to the range hood either through the cabinet or through the wall (Fig.1) Fig.1 2. Insert a screwdriver into the knockout slot and bend the knockout back and forth. (Fig.2) 3. You may have to use pliers to pull the loosened knockout free.(Fig.3) Fig.3 Fig.2 28”-32” 4. When installed, the bottom edge of your range hood should be 28" ~ 32" above the top of the cooking surface. (Fig.
F. Preparing The Installation Location 1. If you want to move the electric range to make room for working on the cabinet turn off the 220 volt power for the electric range at the service entrance. 2. Before moving a gas range, shut off the gas. NOTE: SKIP FOLLOWING STEPS 3A THROUGH 3D IF THE HOOD IS TO BE MOUNTED ON A CABINET WITH A FLUSH BOTTOM . 3. For installation onto a recessed bottom cabinet: a. Measure the space (under the cabinet between the inside front edge and inside back edge (Fig.5).
c. Screw the four 1" wood screws (for mounting the hood) into the exact center of the arrow and into the keyhole mounting slots marked on the cabinet bottom (for flush installations), or marked on the 1” x2” wood strips (for Strips secured recessed cabinet installation) (Fig.7) Do not turn the mounting screws in all Fig.7 the way. Allow 3/8" of screw to project, so the hood can be fitted place. (The screws will be tightened later) G. Providing Electrical Power 1.
WIRING TO POWER SUPPLY SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. Connect the electrical wires. - Connect three wires (black, white and green) to house wires and cap with wire connectors.
H. Installation a. Mounting Range Hood To Cabinet 1. Position the hood in place so that : a. The electrical line is routed through the appropriate Knockout opening. This step will have to be accomplished while positioning the hood (Fig.10) b. The large part of the keyhole mounting slots on the hood fit onto the hood mounting screws projecting from the bottom of the cabinet. (Fig.11) 2. Adjust the hood so the front is flush with the cabinet front. 3.
b. Wall Mount Installation ROOF CAP a. Decide the location and measure the length of PIPE WALL CAP ROUND ELBOW venting pipe from the hood to the outside. (Fig.12) CABINET HOOD Fig.12 b. The less transition, elbows, the more exhaust power performance of the hood. Prepare back wall frame with cross framing lumber (purchase locally) and fix in the appropriation for secure installation (Fig.13) Fig.13 Test for proper operation by temporarily wire the hood before installing.
Apply with eight (3/16" x 3/8" ) screws (included) to fix the Hoo d-M oun t in g two hood-mounting brackets (included) to the back of Bra cke ts the hood. (Fig.16 ) Fig.16 RA-35 Series Mark the desired position of the duct cover mounting bracket on the wall. Fix and secure duct cover mounting bracket with two screws (not included). (Fig.17 ) Fig.17 RA-33/RA-34 Series Aluminum or Steel Pipe Apply with aluminum or steel pipe to connect the plastic Duct Tape exhaust duct on the hood.
c. Install Accessory RA-33/RA-34 Series RA-35 Series Fig.21 1. Refer to Fig. 21 ① Slide the baffle filter into the hood. ② Push the baffle filter up ward. ③ Slide forward. ④ Pull downward. ⑤ Fit into place. 2. For bottom casing, repeat above steps.
I. Replace the LED Light Before replacing LED light ensure the unit is switched off, when you want to change the LED light, please always wear working gloves. 1. Using suitable tool (small slotted screw driver) gently pry off the LED light set. 2. Taking off the wire connecter with LED light set. 3. Replace a new LED light set and reconnect the wire to the connector. 4. Before push back the original LED light position, test the LED light. LED driver: Model: HP1500-36 input: 100~240vdc output: 3.
J. Maintenance Instruction 1. Maintenance should be important than repair. Please take care of the needed maintenance in order to secure and extend the excellent functions and using life. Note: Before repairing the range hood. Disconnect the power source. 2. After using the machine, wipes the machine by neutral detergent in order to keep it clean and maintain the appearance with brightness and sanitation. 3.
L. Use and Care Note: Operate switches (Fig.22) Switch 1 : LED Fan speed indicator. 3 - Low speed 1 ④ ③ ② ① - High speed Switch 2 : Speed switch (Three speed fan) 8 Switch 3 : Light switch Fig.22 Switch 4 : Power switch and delay switch. Push once : Delayed shut off. Push twice : Immediate shut off. Note: Range hood should be turn on either before or the same time when cooking begins.
M. Parts layout diagrams MODEL : RA-3330C 3 RA-3336C 5 4 1 6 7 2 8 9 11 RA-3330C 10 RA-3336C 12-1 12 1. Duct cover-Mounting bracket 7. Control board 2. Duct cover (Optional) 8. Processor board 3. Hood-Mounting bracket 9. LED driver 4. Rubber stand 10. Capacitor 5. Hood casing 11. Squirrel cage 6. LED light 12.
MODEL : 3 RA-3430B 5 RA-3436B RA-3442B RA-3448B 4 1 6 7 8 2 9 10 11 RA-3430B RA-3436B 13-1 12-1 13 12 RA-3442B RA-3448B 13-3 13-2 12-2 12-3 1. Duct cover-Mounting bracket 8. Processor board 2. Duct cover (Optional) 9. LED driver 3. Hood-Mounting bracket 10. Capacitor 4. Rubber stand 11. Squirrel cage 5. Hood casing 12. Stainless steel spacer 6. LED light 13. Baffle filter 7.
MODEL : RA-3530B 1 RA-3536B RA-3542B RA-3548B 2 3 5 4 7 6 8 9 10 RA-3530B RA-3536B 12-1 12 11-1 RA-3548B RA-3542B 12-3 12-2 11-2 11-3 1. Duct cover (Optional) 7. Capacitor support 2. Duct cover -Mounting bracket 8. LED driver 3. Hood casing 9. Capacitor 4. LED light 10. Squirrel cage 5. Control board 11. Stainless steel spacer 6. Processor board 12.
N. Circuit Diagrams Fig.23 Details the internal electrical circuit of this range hood unit. Any faults with this unit should only be attended to by a qualified technician. White Yellow Orange Red Brown Black Yellow Capacitor Brown White Blue Gray Red Motor Yellow Brown White Blue Gray Red Motor Brown Black LED driver Black LED light Red Black Power White Ground Fig.
O. Accessories Spare Parts Contents 1 Part WALL HOOD Item OPERATION MANUAL RA-33 Series RA-34 Series RA-3 5 Series Description Spare Parts Contents Spec. Q'ty Item 1 Manual Part 4 Spec.
11 .2” 6” .6” 6” 12” 10 2/3” Min: 19.7” Max: 35.4” Q.
Min: 19.7” Max: 35.4” .2” 22 ” 29-3/4" (RA-3430) 35-3/4" (RA-3436) 41-3/4" (RA-3442) 47-3/4" (RA-3448) RA-3430B RA-3436B RA-3442B RA-3448B Model : RA-3430 : W 29-3/4 " x D 22 " x H 9 " RA-3436 : W 35-3/4 " x D 22 " x H 9 " RA-3442 : W 41-3/4 " x D 22 " x H 9 " RA-3448 : W 47-3/4 " x D 22 " x H 9 " 22 12” 9” 11 2/3” .
3.
Limited Warranty Windster Hoods Inc. warrants this product against defects in material or workmanship as follows: 1) Labor: For a period of one (1) year from the date of purchase, if this product is determined to be defective, Windster will repair or replace the product, at its option, at no charge. After the warranty period, you must pay for all labor charges. During the “labor” warranty period there will be no charge for labor.
Defective Products: All products will be inspected, tested, and carefully packed by the manufacturer before shipping to customers. Products that are damaged during transit can only be exchanged for the same product, under the condition that the customer must get a RMA (Return Merchandise Authorization) from Windster. When products are received defective, you must notify us within the 3 business days of receiving the package. Replacement products are only shipped when the RMA is issued. NO EXCEPTIONS.
WINDSTER TM www.windsterhood.com 2102 N. Seaman Ave., S. El Monte, CA 91733 TEL:(626)350-1015 (626)350-5215 FAX:(626)350-1254 © 2006-2008 Windster Hoods, Inc. Specifications subject to change without notice.
