www.windsterhood.com User’s Manual WALL MOUNT SERIES RH-W30SS RH-W36SS NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON RECEIVING. CLAIM OF DAMAGE AFTER 7 DAYS OF DELIVERY WILL BE DENIED. This unit is designed for indoor residential use only. DO NOT USE OVER A WOOD GRILL OR MOUNT IN OUTDOOR ENVIRONMENT Please read this operation manual thoroughly before using your range hood. Store it in a safe location for when you need to reference it in the future.
TABLE OF CONTENTS 1 Table of Contents Safety Information .............................................................. 2 – 3 Content Checklist ..................................................................... 4 Measurements ........................................................................... 5 Preparation ................................................................................ 6 Installation ...........................................................................
2 SAFETY INFORMATION SAFETY INFORMATION TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK, AND/OR INJURY OBSERVE THE FOLLOWING: Unit is intended for indoor residential use only. If you should have questions, contact the manufacturer at the address or telephone number listed in the warranty. In case the unit should need to be cleaned or repaired, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally.
SAFETY INFORMATION 3 TO REDUCE THE RISK OF FIRE, OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. Regardless of heat level, never leave any surface materials unattended while operating an open flame. Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé). Depending on amount of usage, clean ventilating fans and filters frequently.
4 CONTENT CHECKLIST CONTENT CHECKLIST 1. CONTENTS INCLUDED a. (1) RH-W series range hood assembly (30‖ or 36‖) b. (1) Lower duct cover (17-3/4‖) c. (1) Upper duct cover (17-3/4‖) d. (1) User’s manual e. (1) 7‖ Damper transition adapter collar f. (2) Stainless Steel Baffle Filters (30‖ model only) g. (3) Stainless Steel Baffle Filters (36‖ model only) h. (1) Mounting packet 2. OPTIONAL ACCESSORIES NOT INCLUDED a. RH-WEXTDC (Extension duct cover)(UP TO 10’ CEILING) b.
MEASUREMENTS 28" 5
6 PREPARATION PREPARATION 1. BEFORE YOU START **BE SURE YOUR UNIT WILL FIT YOUR CEILING HEIGHT** **DO NOT INSTALL IF DAMAGED** **RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED** a. Be sure you have all the content of your purchase and required tools for this installation. b. Installation may take at least 2 to 3 hours from start to finish. c. For more efficient air flow limit the amount of elbows or turns used in the duct work. d. Collar size may need to be increased if utilizing a long duct run.
INSTALLATION 7 INSTALLATION 1. WALL MOUNT INSTALLATION a. Make sure all preparation steps are completed. b. Determine your ceiling height to verify if you will require an extension. i. Unit height = 10” ii. Duct cover height = 17-3/4” (lower) + 17-3/4” (upper w/ luvers) iii. Minimum height (duct cover only)= 17-3/4” iv. Maximum height (duct cover only) = 35” v. (OPTIONAL) Extension duct cover height = 39-1/2‖ vi. Maximum height (duct cover with extension only) = 56” c.
8 INSTALLATION 3. DUCTLESS INSTALLATION a. AFTER COMPLETING Step A – G of Section 1 WALL MOUNT INSTALLATION. b. Remove the RH-WDK (ductless kit) and inspect for any sign of defect or damage. (ie. dents, broken inlet) c. Mount the air diverter at the top of the ceiling using the provided toggle bolt anchors. d. Make sure the duct cover vent opening aligns with the air diverter. (Fig. 2e) e. Connect the exhaust pipe to the collar of the unit. (Fig. 2b) f.
INSTALLATION DIAGRAM INSTALLATION DIAGRAM 9
10 OPERATION & FEATURES OPERATION & FEATURES 1. EASY ACCESS CONTROL SWITCH (from left to right) a. Button 1 – Power ON / OFF b. Button 2 – Low Speed c. Button 3 – Medium Speed d. Button 4 – High Speed e. Button 5 – Light Switch 2. STAINLESS STEEL BAFFLE FILTERS a. (2) 14-1/2‖ x 13-1/2‖ stainless steel baffle filters (30‖ model only) b. (3) 14-1/2‖ x 11‖ stainless steel baffle filters (36‖ model only) 3. CHARCOAL FILTERS **DO NOT WASH CHARCOAL FILTERS! IT WILL DISSOLVE!!** a.
CLEANING & MAINTENANCE 11 CLEANING& MAINTENANCE WARNING!!! To prevent the possibility of a fire and explosion, do not use flammable liquids or solvents to clean the unit or any of its parts. Check to make sure all power sources are disconnected before servicing or taking unit apart for cleaning. Please thoroughly clean the unit weekly as stainless steel can rust under certain condition or by improper cleaning. 1. RANGE HOOD a.
12 TROUBLESHOOTING TROUBLESHOOTING WARNING!!! Check to make sure all power sources are disconnected before starting any troubleshooting. Safety gloves and glasses should be worn when working on the unit. Serious injury or death may occur if safety precautions are not followed. RH-W Series Light Issue LED (All not turning on) 1. Locate and Replace defective Fixture (All Fixtures run on same circuit) 2. New Transformer replacement is required. LED light issue 1. Check all wiring to and from the unit. 2.
PART LIST / REPLACEMENT/ WIRING DIAGRAM 13 PART LIST / REPLACEMENT # Description # Description 1 2 3 4 Duct cover bracket Duct cover Hood bracket Hood body assembly 7 8 9 10 Transformer Capacitor Transition collar Squirrel cage motor 5 6 LED lights Control switch 11 Baffle filter WIRING DIAGRAM
14 WARRANTY / CONTACT US WARRANTY / CONTACT US LIMITED WARRANTY Windster Hoods Inc. warrants its product against defects in material or workmanship as follows: Parts: Windster Hoods, Inc. will supply, at no charge, new or rebuilt replacements in exchange for defective parts for a period of two (2) years. After the warranty period, you must pay for all parts costs. During the "parts" warranty period, there will be no charge for parts Motor: Windster Hoods, Inc.
WARRANTY / CONTACT US 15 WHAT IS NOT COVERED BY MANUFACTURER WARRANTY 1. Damages resulting from any of the following: a. Improper installation or maintenance b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized service dealer c. Misuse, accidents, and/or neglect d. Incorrect electric current, voltage or power supply e. Improper setting of any control (Pressing multiple selections at the same time) f. 2.