www.windsterhood.com UNDER CABINET SERIES User’s Manual WS-208L30SS WS-208L36SS NOTE: This unit does not support ductless operation. For ductless operation, please refer to model WS208LF30SS or WS208LF36SS For residential and indoor use only Please read this operation manual thoroughly before using your range hood. Store it in a safe location for when you need to reference it in the future.
TABLE OF CONTENTS 1 Table of Contents Safety Information ............................................................... 2 - 3 Content Checklist ..................................................................... 4 Measurements ........................................................................... 5 Preparation .......................................................................... 6 - 7 Installation ............................................................................
2 SAFETY INFORMATION SAFETY INFORMATION TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK, AND/OR INJURY OBSERVE THE FOLLOWING: • Unit is intended for indoor residential use only. If you should have questions, contact the manufacturer at the address or telephone number listed in the warranty. • In case the unit should need to be cleaned or repaired, switch power off at either breaker or by disconnecting the power cord from the outlet.
SAFETY INFORMATION 3 TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: • Regardless of heat level, never leave any surface materials unattended while operating an open flame. • Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé). • Depending on amount of usage, clean ventilating fans and filters frequently. Grease should not be allowed to accumulate on fan or filter.
4 CONTENT CHECKLIST CONTENT CHECKLIST 1. CONTENTS INCLUDED a. (1) WS208L30SS or WS208L36SS hood assembly b. (1) User’s manual c. (1) Black 6” to 7” conversion collar d. (2) Aluminum filters & (1) stainless steel filler (30” model only) e. (3) Aluminum filters (36” model only) f. (1) Screw packet 2. CONTENTS NOT INCLUDED a. WS208LCFMR (CFM reducer) 3. TOOLS REQUIRED (NOT INCLUDED) a. Safety gloves b. Safety glasses c. Electric drill w/ starter bit d. Utility knife e.
MEASUREMENTS 5
6 PREPARATION PREPARATION 1. BEFORE YOU START a. Be sure you have all the content of your purchase and required tools for this installation. b. Installation may take at least 1 to 2 hours from start to finish. c. Plan to use as few elbows or turns as possible for more efficient air flow. d. Collar size may need to be increased if utilizing a long duct run. e. At least 12” of duct is required before using an elbow or making a turn. f.
PREPARATION e. 7 For cabinet with recessed-bottom, use (2) 3” x 12” or 15” wood strips on both sides to balance the recession. Use (4) 1-1/4” long flat head screws to secure the wood strips to cabinet. (Fig. 1c) 3. HOOD a. Inspect for any sign of defect or damage. (ie. scratches, dents, loose seams, etc.) b. Power up the unit to make sure it is working properly. c. Remove (2) aluminum filters and (1) stainless steel filler. (30” model only) d.
8 INSTALLATION INSTALLATION 1. DUCTED INSTALLATION a. Make sure all preparation steps are completed. b. Feed the wires coming out of the hood through the bottom of the cabinet. c. Lift the unit up flesh against the wall and the bottom of the cabinet. d. Using the screws and washers provided, insert into each of the keyhole openings and tightly secure the unit against the bottom of the cabinet. NOTE: Install more screws through the back of the unit if necessary. e.
INSTALLATION 9 2. COLD WEATHER INSTALLATION (OPTIONAL) a. Check with your local building codes to see if a CFM reducer is an acceptable alternative to make-up air. b. Remove the WS208LCFMR (CFM Reducer) and inspect for any sign of defect or damage. (ie. Cracks, broken flips) c. AFTER COMPLETING Step A – D of Section 1 UNDER CABINET INSTALLATION d. Place the CFM reducer onto the outlet of the unit and seal the connection point with aluminum tape. (Be sure it is secure with no opening or gaps) e.
10 OPERATION & FEATURES OPERATION & FEATURES 1. EASY ACCESS CONTROL SWITCH (Left to Right) a. Button 1 – ON/OFF b. Button 2 – Low speed c. Button 3 – Medium speed d. Button 4 – High speed e. Button 5 – Lights ON/OFF 2. FAN SPEED a. Button 2 Low speed – 200 CFM / ___ Sones b. Button 3 Medium speed – 410 CFM / ___ Sones c. Button 4 High speed – 620 CFM / 5.4 Sones 3. LED LIGHTING a. (2) 65 lm/w each b. Color – Warm White 5000-5500K 4. ALUMINUM FILTERS a.
CLEANING & MAINTENANCE 11 CLEANING & MAINTENANCE WARNING!!! To prevent the possibility of a fire and explosion, do not use flammable liquids or solvents to clean the unit or any of its parts. Check to make sure all power sources are disconnected before servicing or taking unit apart for cleaning. 1. RANGE HOOD a. Use household cleaner to remove grease or dirt from the outer shell of the unit. Spray on wiping cloth or sponge and wipe in the direction of the grain to avoid scratching the unit.
12 TROUBLESHOOTING TROUBLESHOOTING WARNING!!! Check to make sure all power sources are disconnected before starting any troubleshooting. Safety gloves and glasses should be worn when working on the unit. Serious injury or death may occur if safety precautions are not followed.
PART LIST / REPLACEMENT 13 PART LIST / REPLACEMENT # Description # Description 1 Hood body 8 Motor 2 LED light 9 Teflon fan impeller 3 LED transformer 10 Oil funnel 4 Control switch 11 6" - 7" transition collar 5 Inner bracket 12 6" round collar 6 Capacitor 13a (3) aluminum filters 7 Air chamber 13b (2) aluminum filters / (1) filler
14 WARRANTY / CONTACT US WARRANTY / CONTACT US LIMITED WARRANTY Windster Hoods Inc. warrants its product against defects in material or workmanship as follows: Labor: For a period of one (1) year from the date of purchase, if the product is determined to be defective, Windster will repair or replace the product, at its option, at no charge. After the warranty period, customer must pay for all labor charges. During the "labor" warranty period there will be no charge for any work done on the purchased model.
WARRANTY / CONTACT US WHAT IS NOT COVERED BY MANUFACTURE WARRANTY 1. Damages resulting from any of the following: a. Improper installation or maintenance b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized service dealer c. Misuse and/or accidents d. Incorrect electric current, voltage or power supply e. Improper setting of any control (Pressing multiple selections at the same time) f. 2.