www.windsterhood.com LINER SERIES User’s Manual WS-69TB30 (22”) WS-69TB36 (22”) WS-69TS30 (18”) WS-69TS36 (18”) NOTE: This unit was designed for indoor residential use and DUCTED operation only. DO NOT USE OVER A WOOD GRILL OR MOUNT OUTDOOR ENVIRONMENT. Please read this operation manual thoroughly before using your range hood. Store it in a safe location for when you need to reference it in the future.
TABLE OF CONTENTS 1 Table of Contents Safety Information .............................................................. 2 – 3 Content Checklist ..................................................................... 4 Measurements ........................................................................... 5 Preparation ............................................................................... 6 Installation .................................................................................
2 SAFETY INFORMATION SAFETY INFORMATION TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK, AND/OR INJURY OBSERVE THE FOLLOWING: Unit is intended for indoor residential use only. If you should have questions, contact the manufacturer at the address or telephone number listed in the warranty. In case the unit should need to be cleaned or repaired, switch power off at either breaker or by disconnecting the power cord from the outlet.
SAFETY INFORMATION 3 TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Regardless of heat level, never leave any surface materials unattended while operating an open flame. Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé). Depending on amount of usage, clean ventilating fans and filters frequently. Grease should not be allowed to accumulate on fan or filter.
4 CONTENT CHECKLIST CONTENT CHECKLIST 1. CONTENTS INCLUDED a. (1) WS-69 series (30” or 36”) hood assembly b. (1) User’s manual c. (1) 6” to 7” conversion collar d. (2) Baffle filters w/ handles & (2) stainless steel filler (30” model only) e. (2) Baffle filters w/ handles & (2) stainless steel filler (36” model only) f. (1) Screw packet 2. CONTENTS NOT INCLUDED a. WS-69CFMR (CFM reducer) b. 6” / 7” Aluminum or metal piping 3. TOOLS REQUIRED (NOT INCLUDED) a. Safety gloves b.
MEASUREMENTS 5
6 PREPARATION PREPARATION 1. BEFORE YOU START a. Be sure you have all the content of your purchase and required tools for this installation. b. Installation may take at least 1 to 2 hours from start to finish. c. Plan to use as few elbows or turns as possible for more efficient air flow. d. Collar size may need to be increased if utilizing a long duct run. e. At least 12” of vertical duct is required before any turn. f. Do not try to install this unit by yourself, SERIOUS INJURY MAY OCCUR. g.
INSTALLATION 7 INSTALLATION 1. DUCTED INSTALLATION a. Make sure all preparation steps are completed. b. Determine where you would like to mount the hood. c. Lift the unit up flush against the wall. d. Be sure the unit is leveled and parallel. e. Using the screws and washers provided, tightly secure the unit against the wall and the cabinet frame. NOTE: Install additional screws through the back of the unit if necessary. f. Use the conversion collar for 7” ducting. (OPTIONAL) g.
8 INSTALLATION DIAGRAM
OPERATION & FEATURES OPERATION & FEATURES 1. EASY ACCESS KNOB CONTROL a. Knob 1 – Light ON / OFF b. Knob 2 – Speed i. 1 – Low speed ii. 2 – Medium speed iii. 3 – High speed 2. BAFFLE FILTERS a. (2) 14-3/8” x 12-3/4” baffle filters and (2) fillers (30” model only) b. (2) 14-3/8” x 12-3/4” baffle filters and (2) fillers (36” model only) 3. REMOVING THE BAFFLE FILTERS 1 Slide the baffle filter into the hood. ○ 2 Push the baffle filter upward. ○ 3 Slide the baffle filter toward you.
10 OPERATION & FEATURES
OPERATION & FEATURES 11
12 CLEANING & MAINTENANCE CLEANING & MAINTENANCE WARNING!!! To prevent the possibility of a fire and explosion, do not use flammable liquids or solvents to clean the unit or any of its parts. Check to make sure all power sources are disconnected before servicing or taking unit apart for cleaning. 1. RANGE HOOD a. Use household cleaner to remove grease or dirt from the outer shell of the unit. Spray on wiping cloth or sponge and wipe in the direction of the grain to avoid scratching the unit.
TROUBLESHOOTING 13 TROUBLESHOOTING WARNING!!! Check to make sure all power sources are disconnected before starting any troubleshooting. Safety gloves and glasses should be worn when working on the unit. Serious injury or death may occur if safety precautions are not followed. WS-69 Series Light Issue (One light not turning on) 1. Replace defective GU10 Fixture with new fixture. Filters loose 1. Ensure inside springs are properly expanded Control Knobs not working correctly 1.
14 PARTS LIST / REPLACEMENT PARTS LIST / REPLACEMENT # Description # Description 1 6” round collar 6 Control knob 2 Hood body assembly 7 Motor 3 Halogen / LED lights 8 Oil tray 4 Light cover 9 Baffle filters 5 Capacitor
WARRANTY / CONTACT US 15 WARRANTY / CONTACT US LIMITED WARRANTY Windster Hoods Inc. warrants its product against defects in material or workmanship as follows: Labor: For a period of one (1) year from the date of purchase, if the product is determined to be defective, Windster will attempt to repair the product, at its option, at no charge. After the warranty period, customer must pay for all labor charges. During the "labor" warranty period there will be no charge for any work done on the purchased model.
16 WARRANTY / CONTACT US WHAT IS NOT COVERED BY MANUFACTURE WARRANTY 1. Damages resulting from any of the following: a. Improper installation or maintenance b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized service dealer c. Misuse and/or accidents d. Incorrect electric current, voltage or power supply e. Improper setting of any control (Pressing multiple selections at the same time) f. 2.
