www.windsterhood.com UNDER CABINET SERIES User’s Manual WS-4830SS WS-4836SS WSC-4630SS WSC-4636SS NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON RECEIVING. CLAIM OF DAMAGE AFTER 7 DAYS OF DELIVERY WILL BE DENIED. This unit is designed for indoor residential use only. DO NOT USE OVER A WOOD GRILL OR MOUNT IN OUTDOOR ENVIRONMENT. Please read this operation manual thoroughly before using your range hood. Store it in a safe location for when you need to reference it in the future.
TABLE OF CONTENTS 1 Table of Contents Safety Information .............................................................. 2 – 3 Content Checklist ..................................................................... 4 Measurements ........................................................................... 5 Preparation ......................................................................... 6 – 7 Installation ..........................................................................
2 SAFETY INFORMATION SAFETY INFORMATION TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK, AND/OR INJURY OBSERVE THE FOLLOWING: Unit is intended for indoor residential use only. If you should have questions, contact the manufacturer at the address or telephone number listed in the warranty. In case the unit should need to be cleaned or repaired, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally.
SAFETY INFORMATION 3 TO REDUCE THE RISK OF FIRE, OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. Regardless of heat level, never leave any surface materials unattended while operating an open flame. Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé). Depending on amount of usage, clean ventilating fans and filters frequently.
4 CONTENT CHECKLIST CONTENT CHECKLIST 1. CONTENTS INCLUDED a. (1) WS(C)-48(46) series (30” or 36”) hood assembly b. (1) User’s manual c. (1) Black 6” to 7” conversion collar d. (2) Magnetic baffle filters (30” model only) e. (3) Magnetic baffle filters (36” model only) f. (1) Screw packet 2. CONTENTS NOT INCLUDED a. WS(C)-48(46)CFMR (CFM reducer) b. WS46RVK (Rear vent kit) c. 6” / 7” Aluminum or metal piping 3. TOOLS REQUIRED (NOT INCLUDED) a. Safety gloves b. Safety glasses c.
MEASUREMENTS 5
6 PREPARATION PREPARATION 1. BEFORE YOU START **DO NOT INSTALL IF DAMAGED** **RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED** a. Be sure you have all the content of your purchase and required tools for this installation. b. Installation may take at least 2 to 3 hours from start to finish. c. Plan to use as few elbows or turns as possible for more efficient air flow. d. Collar size may need to be increased if utilizing a long duct run. e. At least 12” of vertical duct is required before any turn.
PREPARATION e. 7 For cabinet with recessed-bottom, use (2) 3” x 12” or 15” wood strips on both sides to balance the recession. Use (4) 1-1/4” long flat head screws to secure the wood strips to cabinet. (Fig. 1d) 3. HOOD a. Inspect for any sign of defect or damage. (ie. scratches, dents, loose seams, etc.) b. Power up the unit to make sure it is working properly. c. Remove the protective film on the baffle filters and fillers.
8 INSTALLATION INSTALLATION 1. UNDER CABINET INSTALLATION (Top round outlet) a. Make sure all preparation steps are completed. b. Feed the wires coming out of the hood through the bottom of the cabinet. c. Lift the unit up flush against the wall and bottom of the cabinet. d. Using the screws and washers provided, insert into each of the keyhole openings and tightly secure the unit against the bottom of the cabinet. NOTE: Install more screws through the back of the unit if necessary. e.
INSTALLATION 9 3. UNDER CABINET INSTALLATION (Rear rectangular outlet)(Optional) a. Make sure all preparation steps are completed. b. Be sure you have the WS38RVK (rear vent kit) to change the top round outlet to a rear rectangular outlet. c. Convert 6” top round to 3-1/4” x 10” rear rectangular. d. Replace the 6” round duct with half round section duct. e. Use a flat-head screwdriver to pry open the rear outlet cover. f. Remove the screws holding the rear outlet panel. g.
OPERATION & FEATURES 10 OPERATION & FEATURES 1. EASY ACCESS CONTROL SWITCH (from left to right) WS-48 WSC-46 a. Button 1 – ON / OFF b. Button 2 – 1 speed c. d. a. st nd Button 3 – 2 speed rd Button 4 – 3 speed Button 1 – ON / Delay Shutoff / OFF b. c. st Button 2 – 1 speed nd Button 3 – 2 speed rd e. Button 5 – Lights ON / OFF d. Button 4 – 3 speed f. Button 6 – Delay Shutoff e. Button 5 – Lights ON / OFF 2. GU10 LED 6W LIGHT FIXTURES a.
STEP BY STEP DIAGRAM 11
12 CLEANING & MAINTENANCE CLEANING & MAINTENANCE WARNING!!! To prevent the possibility of a fire and explosion, do not use flammable liquids or solvents to clean the unit or any of its parts. Check to make sure all power sources are disconnected before servicing or taking unit apart for cleaning. Please thoroughly clean the unit weekly as stainless steel can rust under certain condition or by improper cleaning. 1. RANGE HOOD a.
TROUBLESHOOTING 13 TROUBLESHOOTING WARNING!!! Check to make sure all power sources are disconnected before starting any troubleshooting. Safety gloves and glasses should be worn when working on the unit. Serious injury or death may occur if safety precautions are not followed. WS(C)-48(46) Series GU10 LED Light Issue (One light not turning on or all not turning on) 1. Replace old defective GU10 fixture with new GU10 LED 6W light fixtures found for your convenience at your local hardware store.
14 PART LIST / REPLACEMENT PART LIST / REPLACEMENT
WARRANTY / CONTACT US 15 WARRANTY / CONTACT US LIMITED WARRANTY Windster Hoods Inc. warrants its product against defects in material or workmanship as follows: Labor: For a period of one (1) year from the date of purchase, if the product is determined to be defective, Windster will attempt to repair the product, at its option, at no charge. After the warranty period, customer must pay for all labor charges.
WARRANTY / CONTACT US 16 WHAT IS NOT COVERED BY MANUFACTURE WARRANTY 1. Damages resulting from any of the following: a. Improper installation or maintenance b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized service dealer c. Misuse and/or accidents d. Incorrect electric current, voltage or power supply e. Improper setting of any control (Pressing multiple selections at the same time) f. 2.