Full Product Manual

TOP
1
10
8
BOTTOM
11
12
13
15
1
WINEGARD COMPANY
Tolerances
unless noted:
HDWE PKG
BOW-TIE
TRADE SECRET
The information and data contained herein is secret and shall not be disclosed,used or duplicated
for any purpose whatsoever without written permission of WINEGARD COMPANY, 3000 Kirkwood ST.,
Burlington, Iowa 52601. This legend shall be marked on any reproduction hereof in whole or in part.
Reciept of this document shall be deemed acceptance of the conditions specified herein.
.XX
.XXX
HOLE
ANGLE
ECN NO. DATE REV DESCRIPTION BY
7/3/17 0 APPROVED FOR PRODUCTION QA
P/N: 2762070 DRAWN BY: M. TAEGER
SCALE: 0.750 DATE: Jan-13-17
SHEET
1
of
1
DWG: 2762070
ID# P/N DESCRIPTION QTY
1
2160405 SCREW, 8-16X5/8 PLASTITE, BLK 4
2
2160406 SCREW, 8-32X3/4 PPHMS, BLK 2
3
2160407 SCREW, 8-32X3/8 PPHMS, BLK 2
4
3200489 UPPER ADAPTER 1
5
3200490 LOWER ADAPTER 1
6
2160238 SCREW, CAP 4
7
2160024 WASHER, FLAT 6
8
2160220 NYLOCK NUT 2
9
2744984 MAST CLAMP 1
10
2431005 BAG,6X8 CLEAR US 1
NOTES:
1. HARDWARE BAG MUST BE 6" X 8" MAXIMUM.
BAG MAY BE SMALLER.
2. AN AIR HOLE OR PERFORATION MUST BE PRESENT
TO PREVENT THE BAG FILLING UP WITH AIR.
THE HOLE MUST BE SMALL ENOUGH THAT NO PORTION
OF ANY PART WILL PROTRUDE FROM THE BAG.
3. THE SEAL ON THE BAG MUST BE THE FULL LENGTH
OF THE BAG, AND MUST NOT BREAK.
4. ADD LABEL THAT READS:
"HDW PKG, BOW-TIE - 2762070"
1
2
3
4
5
6
8
7
9
11
12
13
14
15
8
9
10
VHF Antenna
Elements
2
3
Reflector
Assembly
4
Reflector
Elements
J-Pipe
6
Mount Foot
5
Antenna
Assembly
1
Antenna Components
1. Antenna Assembly (1)
2. VHF Antenna Elements (2)
3. Reflector Assembly (1)
4. Reflector Elements (6)
5. Mount Foot (1)
6. J-Pipe (1)
7. Amplifier (1)
Hardware Bag
8. 5/8” Screw (4)
9. 3/4” Screw (2)
10. Upper Adapter, longer (1)
11. Lower Adapter, shorter (1)
12. Bolt (4)
13. Washer (6)
14. Nut (2)
15. Mast Clamp (1)
Specifications
Amplified VHF/UHF antenna
Dimensions of antenna head:
29.28”w x 26.24”h w/mt x 12.1”d w/mt
Assembly required
Recommended for use with RG-6
coaxial cable (not included)
Weather proof connector recommended
(not included)
Mounting supplies: pipe, foot, &
hardware for connecting antenna
head to pipe and foot
Other parts included: 3’ USB cable,
power inserter, 110V wall adapter
Antenna Assembly
STEP 1.
Place the Antenna Assembly (#1) so that the Winegard logo is
facing upward. Attach the Upper Adapter (#10) to the top portion
of the Antenna Assembly (#1). Align the holes, and use two 5/8”
screws (#8) to tighten, using a Phillips screwdriver.
STEP 2.
Place Mast Clamp (#15) on the bottom portion of the Antenna
Assembly (#1). Set the Lower Adapter (#11) on top of the Mast
Clamp (#15) and align the holes. Use two bolts (#12) with washers
(#13) and turn bolts three times by hand to loosely secure, to allow
for the placement of the J-Pipe (#6) at a later step.
7