LIMITED WARRANTY This warranty extends to the origins! purchaser only. This warranty is not transferable, between homes or owners and is only applicable to residential use. Windily industries, LLC provides a 3-year Baited parts warranty for all range hoods. Under this warranty, you {the customer), Is entitled to replacement pairs at no cost to repair and restore functionality if any part of the product were to fall, No labor is provided.
( IMPORTANT SAFETY INSTRUCTIONS ] WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE FOLLOWING: » Use this unit only in the manner intended by the manufacturer. If you have questions, please contact the manufacturer. » Before servicing or cleaning the unit, switch the power off and turn power off at the electrical panel and lock the service panel. This will prevent the power from accidentally turning on.
WARNING: TO REDUCE THE RISK OF INJURY, IN THE EVENT OF A RANGE TOP GREASE FIRE, READ THE FOLLOWING: SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner, BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately. EVACUATE AND CALL THE FIRE DEPARTMENT. 3 NEVER PICK UP A FLAMING PAN ~ you may be burned, ¥ DO NOT USE WATER, including wet dishcloths or towels ~a violent steam explosion will result.
VENTILATION REQUIREMENTS General requirements » Range hoods must be ventilated to the outdoors, except for non-vented {recirculating} Installations. Do not ventilate the range hood Info an attic or other enclosed areas. Do not use 47 {10.2 em) laundry-type wall caps. The length of the range hood and the number of elbows should be kept toa minimum to provide maximum performance.
Roof venting Wall venting B B Exhibit A Na Anacreon avatar osm _| ol INSTALLATION INSTRUCTIONS for Wall Mount Range Hood Parts supplied {Note: The fasteners included may not be suitable to your wall structure. Please check with the installer on proper fasteners to be used based on the material makeup of your wall) A. Range Hood 8B. Power Cord {attached to range hood} round vent alr flap depending on model. {attached to range hood on top of unit) D.
installing the range hood This installation Is for mounting the product to a wall, Ensure your wall has the proper support to hold the range hood weight. These instructions are general guidelines, please consult your installation specialist regarding the best type of mounting hardware and support system based on your wall construction. All well mounted range hoods, if possible, should be installed and supported by studs behind the well (hardware not included).
11. Assemble ventilation to outside ducting. install {1} round flexible duct exhaust hose {i} to round vent air flap {C} {attached to range hood on top of unit} and secure with duct tape. Note: If you are choosing the ductless/recirculating made do not install the duct exhaust hose (i). Power the hood by connecting the three-pronged plug to a nearby electrical outlet.
FILTER INSTALLATION FOR DUCTLESS (RECIRCULATING) MODE IMPORTANT: If you are choosing the ductiess/recirculating mode do not install the duct exhaust hose {i}. 1. Unplug the power cord. 2. Remove the filter panels} located at the bottom of the range hood. 3. Locate the motorized fan inside the hood. 4.
¢ in standby mode, press the Plus bunion one time, the range hood will start at FG speed for 5 seconds for an Initial suction burst then twill automatically reduce to F5 speed. if the button Is pressed again, the speed will stay the same, * To lower or increase the fan speed press the Plus ov Minus buttons. » When fan is in the standby mode, press the Fan button to reach maximum speed immediately. Touching this button while in a lower speed will automatically take to the maximum speed.
CARE and MAINTENANCE Cleaning IMPORTANT: Clean tha hood and panel filters frequently per the following instructions. Replace the pane! filters before operating hood. Exterior Surfaces To avoid damage to the exterior surface, do not use steel wool or soap filled scouring pads. Always wipe dry to avoid water marks, Cleaning Method Use liquid mild-detergent soap and water, do not use hard abrasive cleaners. Wipe with damp soft cloth or non-abrasive sponge, then rinse with clean water and wipe dry.
