User Manual Model Use & Care Guide 5300-2 xx Please read and follow all safety rules and instructions in this manual before operating. xx The product warranty is printed on the back of this guide, so please keep it in a safe place for future use.
CONTENTS 3-Stage Air Purification Controls 3 4 Where to use Installing the filters 5 6 Set Up Safety Instructions Safety and Cautions 8 Operation Initial Operation Modes of Operation Features and Settings 9 10 11 Care and Maintenance Filter Care Cleaning Care 13 17 Troubleshooting Frequently Asked Questions 18 Unit Specifications Product Warranty 20 22 This product is suitable for 120V only.
-STAGE AIR PURIFICATION Odor sensor ➌ PlasmaWave® Light sensor Control Panel / Display Panel ➋ True HEPA filter ➊ Odor Absorbing Carbon Filter Pre-filter Power cord with plug (This product is suitable for 120V only.
CONTROLS Air Outlet Vent Reset Button PlasmaWave® Indicator Indicates whether PlasmaWave® is enabled or disabled. After replacing a filter, press the RESET button for at least 5 seconds. Timer Indicator If timer has been set, the LED light indicates the set time of operation. Mode Button Press to cycle through and set the desired mode of operation (Auto, Sleep). Fan Speed Indicator Indicates the current fan speed.
WHERE TO USE Allow 12 ~ 18 in. of space between TVs, radios, and other electronic products electromagnetic interference from certain electronics may cause product malfunction. Place indoors away from direct sun light direct exposure may cause product malfunction or failure. Only place on hard, flat surfaces flimsy or slanted surfaces may result in abnormal noise and vibrations. WARNING Follow these instructions to reduce the risk of serious injury or death and to reduce risk of damaging the unit.
INSTALLING FILTERS This product comes with all the required filters. The protective plastic wrap must be removed from the filters before use ※ Operating the unit without removing the plastic wrap may result in product failure. ※ Unplug and make sure the unit is turned off before installing filters. ① Remove the front panel by grasping its upper edge and gently pulling forward.
INSTALLING FILTERS ④ Install the filters until they fit securly in place. 3 True HEPA filter Filters must be installed in this order: 3 True HEPA filter (rear) 2 Carbon filter (middle) 1 Pre-filter (front) 2 Carbon filter 1 Pre-filter • To install the Pre-filter, insert bottom tabs into the slots on either side of the lower part of the unit, then rotate upward to insert the upper tabs into the slots at the top part of the unit until sides audibly click into place.
SAFETY AND CAUTIONS Before operating this equipment, carefully read and follow these safety cautions Ensure filters are inserted before running unit running unit without filters can shorten the units life and cause electric shock or injury. Be sure foreign objects are NOT inserted into the vents on the unit objects can include pins, rods, and coins. Do not touch any part of the interior of the unit with wet hands the high voltage may cause electric shock.
INITIAL OPERATION ① Insert the power cord into an electrical outlet. ② Press the ‘Power’ button. 소피아 Note • During the first 30 seconds of power up, the Air Quality Indicator will cycle through Blue, Yellow and Red colors. The Smart Sensors take approximately 4 minutes to gauge the air quality in the environment, after which normal operation will begin. ③ By default, when the unit first powers on, the mode will be set to Auto with PlasmaWave® enabled.
AUTO & SLEEP 1. Auto Mode Enables auto operation based on the unit's air quality Smart Sensors. ① Press the Mode button to select Auto mode. •The LED ‘Auto’ light will indicate when Auto mode is activated, and operation will begin. 소피아 Note • When in Auto mode the fan speed is automically adjusted according to the indoor air quality. As the indoor air quality improves, the fan speed will automatically be reduced. If the indoor air quality decreases, the fan speed will automatically increase. 2.
MANUAL & TIMER 3. Manual Mode (setting fan speed) Users can opt to manually set the fan speed to Low, Medium, High, or Turbo. ① Press the Fan Speed button to set the desired fan speed. 소피아 1 Note • When Manual Mode is selected, Auto Mode is automatically disabled. 4. Timer The timer can be set to let the unit run for a specified period of time. ① Press the Timer button to select the desired length of time. •When the Timer LED light will indicate the selected length of operation.
PLASMAWAVE® & AIR QUALITY INDICATOR 5. PlasmaWave® By default, PlasmaWave ® is enabled whenever the unit is powered on. ① Press the Plasmawave button, when the unit is on, to enable or disable this feature. 소피아 1 Note • In Auto mode, as the indoor air quality improves, the fan speed will automatically be reduced to Low. • When the unit is running, you may hear a chirping or buzzing sound.
FILTER CARE 1. Know The Filters When the Check Filter indicator LED is on, it is time to replace the True HEPA filter. Indicator Light When to service When to replace 1 Pre-filter none Clean once every 14 days Permanent 2 Carbon filter none Filter Can NOT be WASHED 3 True HEPA filter Replace every 3 months Lasts up to 12 months ※ Intervals between filter replacement may vary depending on environment.
FILTER CARE 2. Removing Filters Turn the unit power off before removing filters. Tabs Latch ▶ ▶ Pre-filter ① Remove the front panel by grasping its upper edge and gently pulling forward. ② Press on the Pre-filter tabs near the top of the filter, release and remove. ③ Pull out the Carbon filter and True HEPA filter. 3. Preparing New Filters ① Remove replacement filters from protective plastic wrap.
FILTER CARE 4. Replacing Filters True HEPA filter Tabs ▶ ▶ Carbon filter Latch Pre-filter ① Insert the True HEPA filter first, then the Carbon filter. ② Insert the Pre-filter. •Insert bottom tabs of the Pre-filter into the slots on either side of the lower part of the unit, then rotate upward to insert the upper tabs into the slots at the top part of the unit until sides audibly click into place.
FILTER CARE 6. Cleaning the filters Intervals between filter cleaning may vary depending on the air quality. ② Use a vacuum cleaner or soft brush to clean the Pre-filter. If it is excessively soiled, rinse in room temperature water. •Do not use detergent or soap. •Allow the filter to dry for 24 hours or more before using. If the pre-filter becomes damaged or in any way needs replacement: Please contact Winix (877)-699-4649 www.winixamerica.
CLEANING CARE 2. Cleaning the Exterior & Interior ① Wipe with a soft damp cloth using room temperature water. Afterwards, wipe it down with a clean dry cloth. •To keep unit in peak condition, clean every 1-2 months. ① Open the front panel and clean the interior with a vacuum cleaner. •For optimal perfomance, clean every 1-2 months. NOTICE •When cleaning the unit, always unplug the power cord first and then wait until the unit has cooled down.
FREQUENTLY ASKED QUESTIONS Problem It does not turn on at all. It doesn’t work in Auto Mode. English Check / Actions to take • Is the plug securely attached to the outlet? - Make sure the outlet has power going to it, and ensure the plug is secured. • Is there a power outage? - Check to see if other lights and electrical equipment are working and try again. • Has Auto Mode been selected? - Press the Mode button until Auto Mode is selected.
FREQUENTLY ASKED QUESTIONS Problem Check / Actions to take It vibrates and makes a lot of noise. • Is it running on a slanted or uneven surface? - Move the unit to a hard, flat, even area of the floor. The power plug and outlet feel hot. • Is the plug securely plugged in? - Make sure the plug is properly plugged into the outlet. There is a strange smell. • Is it being used in a place with a lot of smoke, dust, or odors? - Clean the air intakes on either side and clean the pre-filter.
UNIT SPECIFICATIONS Model Name 5300-2 Power Voltage AC120V/ 60Hz Power Rate 70W Room Area Served 360ft2 Dimensions 14.9 in(W) x 7.8 in(D) x 23.6 in(H) Weight 17.6 lbs Replacement Filter Filter A / Item: 115115 Pre-Filter Part #: 4521-0012-03 ※ The exterior, design, and product specifications may be changed without prior notice to improve product performance.
SAFETY INSTRUCTIONS Thank you for purchasing a Winix air purifier. This product is for household use only. IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER IMPORTANT PRECAUTIONS FOR USING YOUR AIR PURIFIER xxDo not block the intake or outlet vents. xxDo not use near hot objects, such as a stove. xxDo not use where the unit may come into xxDo not repair or modify the unit unless contact with steam. specifically recommended in this manual.
PRODUCT WARRANTY The terms of the warranty are as follows. 1. This product is manufactured under stringent quality control and inspections. 2. Warranty void if product failure is a result of negligence or misuse by the consumer, shipping and service fees may be incurred even during the warranty period. 3. The warranty must be presented upon bringing the product for service. 4. Store the warranty in a safe place, as it cannot be reissued. 5. This warranty is valid only in the USA and Canada.
Developed in partnership with Drexel University (Philadelphia, PA, USA) 151311 Rev.A Contact for product related inquiries and customer service To expedite service, please specify the model name and number, the nature of the problem, your contact information, and your address. Dedicated Call Center : (877) 699-4649 Website : www.winixamerica.