User Manual WINIX AIR CLEANER Model Use & Care Guide ZERO+ (AUS-1250AZPU) ˍˍ Please read and follow all safety rules and instructions in this manual before operating. ˍˍ The product warranty is printed on the back of this guide, so please keep it in a safe place for future use.
CONTENTS 5-STAGE AIR PURIFICATION··············································3 CONTROLS·····························································4 WHERE TO USE·························································5 INSTALLING THE FILTERS················································6 SAFETY AND CAUTIONS·················································8 INITIAL OPERATION·····················································9 AUTO AND SLEEP······················································10 MAN
5-STAGE AIR PURIFICATION 5 PlasmaWave 4 True HEPA filter 3 Deodorization filter 2 Pre-filter 1 Product English Pre-filter/ Deodorization filter/ True HEPA filter Pet filter Pet filter User Manual ZERO+ 3
CONTROLS Air Outlet Vent PLASMAWAVE Check Filter Indicator LED light indicates when it is time to change the filter. Timer Indicator PlasmaWave Indicator Indicates whether PlasmaWave® is enabled or disabled. Smart Sensor Reset Button Automatically detects indoor air quality. After replacing a filter, press the RESET button for at least 5 seconds. If timer has been set, the LED light Indicates the set time of operation.
WHERE TO USE Allow 30 ~ 45 cm of space between TVs, radios, and other electronic products electromagnetic interference from certain electronics may cause product malfunction. Place indoors away from direct sun light direct exposure may cause product malfunction or failure. Only place on hard, flat surfaces flimsy or slanted surfaces may result in abnormal noise and vibrations.
INSTALLING THE FILTERS This product comes with all of the required filters. The protective plastic wrap must be removed from the filters before use. ※ Operating the unit without removing the plastic wrap may result in product failure. ※ Unplug and make sure the unit is turned off before installing filters. ※ The unit will automatically power off when front panel is opened. ① Remove the front panel by grasping its upper edge and gently pulling towards yourself.
INSTALLING THE FILTERS ④ Install the filters until they fit securely in True HEPA filter place. Filters must be installed in this order: 3 True HEPA filter (rear) Deodorization 2 Deodorization filter (middle) filter Pre-filter 1 Pre-filter (front) ˍˍ To install the pre-filter, insert bottom tabs into the slots on either side of the lower part of the unit, then rotate upward to insert the upper tabs into the slots at the top part of the unit until both sides audibly click into place.
SAFETY AND CAUTIONS Before operating this equipment, carefully read and follow these safety cautions and instructions to avoid damage and ensure safe use. Ensure filters are inserted before running unit running unit without filters can shorten the units life and cause electric shock or injury. Be sure foreign objects are NOT inserted into the vents on the unit objects can include pins, rods, and coins.
INITIAL OPERATION ① Insert the unit plug into an electrical outlet. ˍˍ The Control Panel lights will turn on and off. ② Press the 'Power' button. NOTE ˍˍ During the first 4 minutes of power up, the Air Quality light will flash as the Smart Sensors measure the air quality in the environment, after which normal operation will begin. ③ By default, when the unit first powers on, the mode will be set to Auto with PlasmaWave® enabled.
AUTO AND SLEEP Every time the Mode button is pressed, the Mode LED light will cycle through the settings. (Auto, Sleep, Low, Medium, High, Turbo) 1. Auto Mode Enables Auto operation based on the unit's air quality Smart Sensors. ① Press the Mode button to select Auto mode. ˍˍ The mode LED light will indicate when ‘Auto’ mode has been selected, and operation will begin. ˍˍ Each time the Mode button is pressed, the modes will be cycled. (Auto, Sleep, Low, Medium, High, Turbo).
MANUAL MODE, TIMER AND PLASMAWAVE® Every time the Mode button is pressed, the Mode LED light will cycle through the settings. (Auto, Sleep, Low, Medium, High, Turbo) 3. Manual Mode (setting fan speed) Users can opt to manually set the fan speed to Low, Medium, High, or Turbo. ① Press the Mode button to select the desired fan speed. ˍˍ The mode LED light will indicate the selected fan speed, and operation will begin. NOTE ˍˍ When Manual Mode is in use, Auto and Sleep modes are automatically disabled. 4.
CHILD LOCK, AIR QUALITY LED LIGHT 6. Child Lock This feature prevents children from tampering with the control panel. ① Press and hold the Child Lock button for 3 seconds to enable or disable the feature. ˍˍ When the Child Lock indicator is lit, the feature is enabled. ˍˍ When Child Lock is enabled, the control panel is locked and the settings cannot be changed. ˍˍ To disable, press and hold the Child Lock button again for 3 seconds. 3 seconds 7.
FILTER CARE 1. Changing Filters When the Check Filter indicator LED is on, it is time to replace both the True HEPA and Deodorization filter. Filter 1 Pre-filter Indicator Light When to service When to replace none Clean once every 14 days Permanent Can NOT be WASHED Lasts up to 12 months 2 Deodorization filter 3 True HEPA filter ※ Intervals between filter replacement may vary depending on environment.
FILTER CARE 2. Removing Filters Ensure the unit is turned off and unplugged before removing filters. ※ The unit will automatically power off when front panel is opened. ① Remove the front panel by grasping its upper edge and gently pulling towards yourself. ˍˍ To remove the front panel, the latch at the lower edge of the panel must be released from its position. ② Press the tabs on the top edge to remove the 1 Pre-filter.
FILTER CARE 3. Filter Assembly and Replacement Filters should be re-installed in the reverse order of their removal. ① Insert the replacement 3 True HEPA filter (rear) True HEPA filter 2 Deodorization filter (middle) ˍˍ Remove the protective plastic wrap from new filters. Operating the unit without removing the protective plastic wrap may cause abnormal noise, deformation, or fire as a result of overheating. Deodorization filter ② Insert the 1 Pre-filter (front).
FILTER CARE 4. Cleaning the Pre-filter Intervals between filter cleanings may vary depending on the air quality. ① Use a vacuum cleaner or soft brush to clean the Pre-filter. If it is excessively dirty, wash with room temperature water. ˍˍ Use only water, do not use volatile substances such as alcohol or acetone.
CLEANING THE DUST SENSOR Cleaning the Dust Sensor For optimal performance of the Dust Sensor, which detects airborne dust and ultrafine particles, clean it every two months. Clean it more frequently when the unit is running in a place with high dust levels. ① Open the Dust Sensor cover. ② Use a damp cotton swab to wipe the lens and intake area of the Dust Sensor. ˍˍ To clean the sensor area, use only water. Do not use volatile substances such as alcohol or acetone.
CLEANING CARE Cleaning the exterior and interior Cleaning the exterior Wipe with a soft damp cloth using room temperature water. Afterwards, wipe it down with a clean dry cloth. ˍˍ For optimal performance, clean the front panel 1-2 times a month. Cleaning the interior Open the front panel and clean the interior with a vacuum cleaner. ˍˍ For optimal performance, clean the interior 1-2 times a month.
FREQUENTLY ASKED QUESTIONS Problem Check / Actions to take It does not turn on at all. ˍˍ Is there a power outage? -- Check to see if other lights and electrical equipment are working and try again. It doesn’t work in Auto mode. ˍˍ Has Auto mode been selected? -- Press the Mode button until Auto mode is selected. ˍˍ Is the sensor blocked or clogged? -- Clear the sensor using a vacuum cleaner. view page 17. It vibrates and makes a lot of noise.
FREQUENTLY ASKED QUESTIONS Problem Check / Actions to take The power plug and outlet feel hot. ˍˍ Is the plug securely plugged in? -- Make sure the plug is properly plugged into the outlet. There is a strange smell. ˍˍ Is it being used in a place with a lot of smoke, dust, or odors? -- Clean the air intakes on the front sides of the unit and clean the pre-filter. -- Contact customer service to confirm the exact cause. -- Replace the Deodorization filter and True HEPA filter.
UNIT SPECIFICATIONS Model Name AUS-1250AZPU Power Voltage 220 - 240 V, 50 / 60 Hz Power Rate 50 W Recommended room capacity 49.5 m2 Weight 8.5 kg Dimensions 415 mm(W) x 245 mm(D) x 600 mm(H) Replacement Filter FILTER GU, item : 1712-0095-01 FILTER GJ, item : 1712-0092-01 ※ The exterior, design, and product specifications may be changed without prior notice to improve product performance.
SAFETY INSTRUCTIONS Thank you for purchasing a Winix air purifier. This product is for household use only. IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER WARNING : Follow the instructions in this manual to reduce the risk of electric shock, short circuit, and/or fire. ˍˍ Do not repair or modify the unit unless specifically recommended in this manual. All other repairs should be completed by a qualified technician.
PRODUCT WARRANTY Product Name Air Purifier Model Name AUS-1250AZPU Purchase Date Warranty period Two (2) years Place of purchase Place of purchase Tel. Address Customer Name Tel. ※ After purchase, be sure to complete all of the above information.
2610-0208-00 Rev.00 Contact for product related inquiries and customer service To expedite service, please specify the model name and number, the nature of the problem, your contact information, and your address. Distributed by Ausclimate Pty Ltd After sales and warranty enquiries, visit website or call 1800 122 100 Website : www.ausclimate.com.au / www.winixaustralia.com.