Barn Door Hardware Installation Manual www.winsoonhardware.
Track Accessories short lag bolt (2-9/16in) track bolt short spacer (1-3/8in) Double Door Hardware Kit Includes Part Name Flat Track Steel Hanger Anti-jump Type A Type B Pad Floor guide Floor guide Door Stopper Lag Bolt Spacer Junction Plate Bypass Bracket Suit picture 1-3/8in 7.5FT 4 2 4 2 4 2 6 6 0 6 ※ Check the Quantities of Flat Track ,Accessories and Steel Hanger.
※Hardware Installation Prepare Your Doors Step 1: Attach Steel Hangers to Your Doors Drill 3/8” (10mm) holes at the distances from the top of the doors shown in the above chart. Recommended: The Hangers should be between 2”-4” from the door edge to the center of Hanger. Attach Hangers with the Hanger Bolts, Washers and Acorn Nuts as shown below.
Step 2: Cut Floor Guide Slot At The Bottom Of The Door ①If you use type A floor guide , you will need to Cut a 5/16” (7mm) wide, 3/4” (20mm) deep slot at the bottom of the door. Recommended: Cut the slot with a router and slot cutter bit. ②If you use type B floor guide , please skip this step. 5/1 6” (7m m) 3/4 ”( 20 mm ) Step 3: Install anti-jump pad As shown in the illustration, the screw is near the front edge of your door (recommended: drill pilot hole to avoid splitting). Do not over tighten.
Prepare and Install the Tracks Step 4: Draw 3 Lines for the Track and Brackets a.Using a level, draw line ① for the Track, at the door height + 1-11/16” (43mm) above the floor. b.Pencil lines ② and ③ for the Bracket above line ① as shown in the illustrations below. ③ 2”(50mm) ② 8-1/4”(210mm) ① Door Height+1-11/16”(43mm) Step 5: Mark and Drill Track Holes a.Line up a Track on lowest line and mark the location of the holes. b.
Step 6: Install The Inside Track Using the Spacers, Long Lag Screws, and Washers (and hollow wall anchor if necessary), attach the Inside Track to the wall as shown in the illustration below. Tip: Loosely attach one end of the Track with the other end resting on the ground. Then swing track up and attach other end. Finally, fill in the middle holes.
Step 7: Attach Brackets to the Wall a.Loosely attach each bracket to the wall with Short Lag Screws and washers (and hollow wall anchors if needed). b.Fully tighten all Lag Screws with your ratchet. Don’t overtighten screws as you may strip the studs or anchors. c.Type B bracket, please refer to the illustration below.
Step 8: Install the Outside Track Using the short spacers, Track Bolts, Washers and Nuts attach the outside Track to the Bypass Bracket as shown in the illustrations below.
Hanging and Positioning Doors Step 9: Install Your Doors a.Hang your Steel Hangers on the Track, and then twist the Anti-Jump Pad toward the wall so that it is under the Track. b.Position doors in your desired closed position and adjust Door Stoppers to contact the outside edge of the outside Steel Hanger wheel. Repeat with doors in desired open position and the inside Steal Hanger wheel.
Hanging and Positioning Doors Step 9: Install Your Doors a.Hang your Steel Hangers on the Track, and then twist the Anti-Jump Pad toward the wall so that it is under the Track. b.Position doors in your desired closed position and adjust Door Stoppers to contact the outside edge of the outside Steel Hanger wheel. Repeat with doors in desired open position and the inside Steal Hanger wheel.
Step 10: Install the Floor Guide Position the door at your desired open position, put half of the floor guide under the door, mark the location, and then fix guide to the floor.
WARNING • Failure to wear proper safety gear (i.e.,eye protection) may result in serious injury or death. Always wear proper safety gear before using power tools. • Improper operation of power tools may result in loss of control, serious injury or death. Always ensure you have complete control of the power tool and the work area is free of hazards before operatiog a power tool.
