Quick Guide

OPTION TWO
Wi-Fi Repeater Mode
Using WPS (Wi-Fi Protected Setup)
Note:`
1). Some ISP gateways disable the WPS function by default. If the WPS connection fails,
please use OPTION ONE.
2). For more information about using WPS on your router, please refer to the router
manufacturer's user guide.
1. Press the WPS button for 6 seconds on the Extender.
2. Within two minutes, press the WPS button on your router.
3. The Extender will reboot, please wait a few minutes.
Tips:The corresponding WLAN LEDs should
turn on and stay solid, indicating successful
connections.
Press
Press 1~2 seconds
Power ON
1
Connect
2
1.
Switch the mode selector to Repeater position.
2. Plug the Extender into an electrical outlet near your
Wi-Fi router.
3. Shift the power switch to ON and wait until the
POWER LED is on and solid green.
Relocate
3
1.
Plug the Extender into an electrical outlet about halfway between your router (Host Wi-Fi)
and the Wi-Fi dead zone. The location you choose must be within the range of your
existing host Wi-Fi.
Host Wi-Fi
WLAN WLAN
Ideal Location
WLAN WLAN
Flashing
Too Far Away
2.
Wait until the WLAN LEDs are ON. If the signal is weak, relocate it closer to the router
to achieve a good (or better) signal quality.
Management via Web Browser
Change Login Password
1. Visit http://ap.setup, and log in with the password
you set for the Extender before.
2. Click Setup->Login Password.
3. Enter the old password. Then enter the new password
(case-sensitive) and click Apply button.
4. Use the new password for future login attempts.
FAQ (Frequently Asked Questions)
This product includes software codes developed by third parties. These software
codes are subject to either the GNU General Public License (GPL), Version 2, June
1991 or the GNU Lesser General Public License (LGPL), Version 2.1, February
1999. You can copy, distribute, and/or modify in accordance with the terms and
conditions of GPL or LGPL.
The source code should be complete, if you want us to provide any additional
source code files under GNU General Public License (GPL), please contact us in
these matters. We are committed to meeting the requirements of the GNU General
Public License (GPL). You are welcome to contact us local office to get the
corresponding software and licenses. Please inform us your contact details
(full address)and the product code. We will send you a software package with the
software and license for free.
The respective programs are distributed WITHOUT ANY WARRANTY; without
even the implied warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE.
Please refer to the GNU General Public LicenseWeb site for further information.
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html
http://www.gnu.org/licenses/gpl.html
GNU General Public License Notice
Swtich to Repeater Mode
Press 6 seconds
Switch to Repeater Mode
Q1. Why doesn’t the login page appear after entering http://ap.setup ?
• Make sure your computer is connected to the Extended network’s SSID or connect your computer to the
Extender using an Ethernet cable.
• Make sure your computer is set to obtain an IP address automatically.
• Verify that http://ap.setup is correctly entered in the web browser and press Enter.
Q2. What should I do if the LED does not change to solid after completing OPTION ONE?
• You may have entered the incorrect Wi-Fi password of your host Wi-Fi during the configuration. Please log into the Extender’s
web-based interface to check the password and try again.
• Please reset the Extender and go through the configuration again.
Q3. How do I restore the Device to its factory d
Q4. Why my Wi-Fi Extender doesn’t work in AP mode?
efault settings?
• While the Extender is powered on, press and hold the Reset butt
• Make sure the WAN/LAN port of the Extender is connected to the LAN port of your router and then try again.
on until all the LEDs turn on momentarily.
Tips:
1). Use your phone to find the ideal location for
the Extender. If your phone’s Wi-Fi signal
(received from your router) is higher than 3
levels, it is the ideal spot to install the Extender.
If not, we recommend you move it closer to
your router for better Wi-Fi signal.
2). The default extended 2.4G SSID (Wi-Fi name)
will be your router’s SSID with “EXT2.4G” within
and “EXT5G” is for Extended 5G SSID
correspondingly.
3). The extended 2.4G&5G passwords are the
same as your Host passwords.
Wireless Basic Configuration
Apply
Login Password
Status Wizard Wi-Fi Setup
Old Password:
New Password:
Confirm Password:
Firmware Upgrade
2. Click Browse (or Choose File) to locate the downloaded new firmware file.
3. Click Apply button, and wait a few minutes for the firmware upgrade to
complete.
Warranty voids if you interrupted the upgrade procedure.
NOTE: Never interrupt the upgrade procedure by closing the web browser or physically
disconnect your computer from the device. If the procedure is interrupt, the firmware
upgrade will fail, and you may have to return the device to the dealer to ask for help.
Firmware upgrade can fix bugs of the Extender. However, We DO NOT
recommend you upgrade the firmware of the Extender if it works properly.
1. Click Setup->Upgrade Firmware.
Status Wizard Wi-Fi Setup
Upgrade Flrmware
Apply
Version:M78N_V3130.1121
Do NOT power off the device during the firmware upgrade. Wait a few
minutes for the firmware upgrade to complete and the device to reboot.
Browse
Apply
Wi-Fi Setup
Status Wizard Wi-Fi Setup
Hide Wi-Fi:
2.4G SSID:
Security Type:
WPA2-PSK
Wi-Fi ON/OFF:
Wi-Fi Password:
2.4G Wi-Fi Settings
ON
OFF
Hide Wi-Fi:
5G SSID:
Security Type:
WPA2-PSK
Wi-Fi ON/OFF:
Wi-Fi Password:
5G Wi-Fi Settings
ON
OFF
1. Click Wi-Fi -> Wi-Fi Setup.
2. Customize your wireless network
for the Extender.
3. After finishing configuration, click
Apply button and the Extender
will reboot.