Quick Start Guide

ManualsBrandsWinstars Technology ManualsComputers & AccessoriesHigh Power Wireless Repeater

2.4G RP-SMA Antenna Connectors

5G RP-SMA Antenna Connectors

3 x Wi-Fi Signal LEDs

Status LED

WAN/LAN LED

Hardware Overview

WN572HP3

Feature

Default Parameters

LED Indicators

Power

LAN/Backhaul

Status

WAN/LAN

Off

Fast flash

Slow flash

The device is powered on.

The Ethernet port is connected.

The Ethernet port is disconnected.

The Ethernet port is connected.

The Ethernet port is disconnected.

Another router has not been connected

when the device is the repeater mode.

The another router has been connected but the

device has no access to the network in the

repeater mode.

The device keeps on in the AP mode;

The device can access the network normally.

Wi-Fi signal output power 100%.

Better reception: signal 81%~100%.

Good reception: signal 60%~80%.

Weak reception: signal below 0~59%.

The device is not receiving electrical power.

LAN Backhaul LED

POWER LED

Reset/PAIR Button

LAN Backhaul Port

WAN(PoE IN)/LAN Port

Grounding Terminal

Web: http://wifi.wavlink.com

Default IP: 192.168.10.1

Pass RJ45 cable through

the spiral cover

Pass RJ45 cable through

the rubber seal

Pass RJ45 cable through

the holder

Connect the RJ45 cable to

PoE IN/WAN port.

Spin 2.4G antenna into the

2.4G external RP-SMA connector

Spin 5G antenna into the 5G

external RP-SMA connector

Screw the holder

Plug the rubber seal to the holder

Screw the spiral cover

2. Install the device.

2.1 Firstly fasten the device to somewhere firm, then install

the device in the holder.

Remark

If you happen to live in the zone where lightning happens a lot,

we suggest that you install the device through grounding

connection in order to strengthen the lightning-resistant function.

2.2 Now please follow the steps below.

1. Please follow the installation steps when assembling the device.

1) Connect the "PoE" port of PoE converter to the PoE IN(WAN)

port of the device.

2) Connect “LAN DATA IN” to “LAN” of your router.

3) Plug in the device through the power adapter.

4) Push the “ON/OFF” button to turn on or off the device.

Attention

1) Ensure that you use a certified CAT5e/CAT6 Ethernet

cable with RJ45 connectors

2) Make sure the length of the Ethernet cable from PoE to

the device is less than 60 meters (196 ft).

Wi-Fi Signal

Installation

4.4 Router Mode

FAQ Warning

09 10 11 12 13 14

02 03 04 05 06

High Power Wireless Repeater

- Dual band with maximum speed up to 5G 867Mbps and 2.4G 300Mbps.

Weatherproof and build in lightning arrester withstand harsh outdoor conditions.

- Four omnidirectional antennas eliminate Wi-Fi dead zones.

- High power amplifier for stronger signal transmission.

- Gigabit port provides faster connection.

- Passive PoE support for flexible deployment.

- Support AP/Router/Repeater/EasyMesh agent mode.

MU-MIMO function lets the router talk to several devices simultaneously

over the same Wi-Fi band.

2.4G SSID: WAVLINK-N_XXXX

5G/AC SSID: WAVLINK-AC_XXXX

Wireless Password: open

What is firmware upgrade and why do I need it?

Firmware contains fixed for bugs and new features, please keep

the latest firmware to improve the experience of using the

product. Please do not use the wrong firmware, otherwise, it will

damage your device and void the product warranty.

For more details, please visit our website www.wavlink.com

Our Technical Support: support@wavlink.com

1.2 Via Cable

Connect Ethernet cable to your PC/laptop and device’s LAN

Backhaul port, then you can start configuring the device.

1.1 Via Wireless

Configuration

1. Connection

Turn on your Wi-Fi, search SSID of this product on your wireless

devices (smart phone, tablet computer, laptop, etc.) and connect

to it.

WAVLINK-N_XXXX

WAVLINK-AC_XXXX

www.wavlink.com/en_us/WING-12M

Scan the QR code or load the link for

Quick Start Guide downloading

English

Welcome to Wavlink

Please set up this device first!

Please enter your password

2. Technically speaking, the product web UI will guide you

to the login page once you have connected to the device

successfully in your first time, but if it doesn't, please manually

input 192.168.10.1 or wifi.wavlink.com in the address bar of your

browser on PC/laptop or phone, the default password is admin.

3. Select your Country/Region and Time Zone. For your network

security, we suggest that you set a new login password.

Note: The three colored bars in "Change Password" area

indicates the strength of the login password.

4. Mode Selection

This product has four modes.

4.1 Repeater Mode

For Repeater mode, we recommend you choose “WISP”, you

can manually enter the WiFi SSID you need to connect or select

the WiFi SSID in the list, and the Password needs to be the

same as the WiFi password that this product has connected,

then click on “Connect”.

Wireless-AC

Wireless-N

WAVLINK-Mesh

WAVLINK-AX_XXXX

WAVLINK_XXXX

System

WISP-Recommend

Select WI-FI Manual Input

Mode selection

Connect to

Password

2.4G

Connect

5G/2.4G Choose

Network

The Self Management is open in default, you can manage

this device (web UI) through the assigned IP or domain name.

4.2 EasyMesh Agent Mode

If you have a router that supports Easymesh function, then

you can build a mesh system with this mode.

1. Log in to 192.168.10.1 or wifi.wavlink.com.

2. In Mode Selection, please choose “EasyMesh Agent Mode”.

3. Click on the “Start Pairing” button.

Please configure according to the following steps:

4. Now please start pairing process on the Easymesh controller,

if you are not sure how to start, please ask manufacturer for help.

4.3 LAN Bridge (AP mode)

Please connect the LAN DATA IN port of the POE converter or

the LAN Backhaul port of the device to the upper router. Then

you can change the SSID or use the default one, as for the

Encryption Mode, the default is WPA2-PSK, we recommend

you to select WPA3/WPA2-MIX if your devices support. For

your network security, please create a new password according

to the rule. Then click on “Save” and wait for the setting

process to complete.

Before conﬁguring, please make sure your upper router has

connected to the LAN DATA IN port of the PoE converter.

If you choose the Router Mode, the system will guide you to

select the WAN Type. As for the Encryption Mode, the default

is WPA2-PSK, we recommend you to select WPA3/WPA2-MIX

if your devices support. For you network security, we suggest

you create a Password.

Which WAN Type am I supposed to choose?

If you use DSL line and you are only provided an account

name and a password by your ISP, choose PPPoE. If you

use cable TV or ﬁber cable, choose DHCP(Dynamic IP). If

you are provided information such as IP address, Subnet

Mask and Default Gateway, choose Static IP.

When you need to change your Wi-Fi password, please

click on “Wireless”.

Wi-Fi Password Management

4. Click on

to locate the firmware file.

5. Click on “Upload” and choose “Apply”, and wait for the

firmware upgrade process to complete.

Firmware Upgrade

If you need to update firmware, please proceed as the following steps:

1. Download the latest firmware file from Wavlink website.

2. Extract the firmware from the downloaded file.

3. Log in to wifi.wavlink.com or 192.168.10.1, then choose

“Advanced”

and select

“Firmware Update”

Option I

Option II

1.Log in to 192.168.10.1 or wiﬁ.wavlink.com, then choose

“Advanced” and select “Firmware Update”.

2.Click on “Check New Version” to ﬁnd the latest version.

3.Click on“Download and Upgrade”, and wait for the ﬁrmware

upgrade process to complete.

Note: After updating ﬁrmware, please Reset The Device And

Clear Your Browser Cache.

- lf you can’t log in to the lP address or URL in AP Mode,

please check the lP address arranged by the upstream router,

then try to restart the process.

- Make sure you have connected to the WiFi of the

Wavlink device.

- Please try to clean the cache of the browser.

- Try to log in the management page via another browser.

- Try to log in the management page via other devices.

Q2. Why can’t I visit the web UI by inputting the IP

address 192.168.10.1 or wifi.wavlink.com?

- Make sure your Internet works normally, please contact your

ISP(Internet Service Provider) if it doesn't.

- Initiate your browser, enter 192.168.10.1 or wifi.wavlink.com,

then set up the following quick start guide.

- Reboot your device and try it again.

Q1. What can l do if l can not access the Internet? FCC Warning

- Please refer to Q3 to reset the device, the default password

is admin.

Q3. What can l do if l forget my administration

management password?

- Please put your mesh devices in a relatively open space to

avoid obstacles such as metal objects, reinforced concrete

walls and so on.

Q4. How do l find the best location for mesh devices?

WAVLINK-N_050E

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Note:The Grantee is not responsible for any changes or modifications not expressly

approved by the party responsible for compliance. such modifications could void the

user's authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement.

To maintain compliance with FCC RF exposure guidelines, the distance must be at

least 20 cm between the radiator and your body, and fully supported by the

operating and installation configurations of the transmitter and its antenna(s).

IC Warning

This device complies with Industry Canada license-exempt RSS

standard(s). Operation is subject to the following two conditions:

(1). This device may not cause interference.

(2). This device must accept any interference, including interference that

may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux

deux conditions suivantes:

(1). l'appareil ne doit pas produire de brouillage.

(2). l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

The device has been evaluated to meet general RF exposure requirement.

To maintain compliance with RSS-102 — Radio Frequency (RF) Exposure

guidelines, this equipment should be installed and operated with a

minimum distance of 20cm between the radiator and your body.

le dispositif de a été évalué à répondre général rf exposition exigence.pour

maintenir la conformité avec les directives d'exposition du RSS-102-Radio

Fréquence (RF). ce matériel doit être installé et exploité à une distance

minimale de 20 cm entre le radiateur et votre corps.

5G frequency band 5150-5250MHz indoor use only.