READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Twist N Click ® Express Assembly No Tools Required Installation Guide Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pg. 4 Wiring. pg. 4 Canopy Assembly. pg. 5 Blade Assembly. pg. 5 Light Kit Assembly. pg. 6 Testing Your Fan. pg. 6 Troubleshooting. pg. 7 Warranty. pg. 7 Parts Replacement. pg. 7 4009654 net weight of fan: 17.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a a. hanging bracket.1 piece b. canopy (pre-attached to downrod). 1 piece b c. downrod and hanging ball (pre-attached to motor housing). 1 piece c d d.
10ft. - 12ft. (3.05m - 3.66m) blade edge 3. Installation Preparation. 30 inches 7 feet (76cm) (2.13m) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 144 square feet (13.4 square meters). 10ft. - 12ft. (3.05m - 3.66m) downrod installation This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling.
. Fan Assembly. With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab. hanging bracket tab hanging ball slot WARNING: Failure to align slot in hanging ball with tab in hanging bracket may result in serious injury or death.
7. Canopy Assembly. hanging bracket Raise canopy toward ceiling and allow it to attach to hanging bracket using the magnets mounted on each side of the hanging bracket. Carefully peel away the plastic wrapping around the downrod sheath. Note: Should you need to lower the canopy for any reason, use care in lowering the canopy over the downrod sheath to prevent scratching the metal surfaces. magnet canopy 8. Blade Assembly.
9. Light Kit Assembly. Remove socket covers from sockets on light kit fitter. Attach glass shades to sockets, securing with socket covers. light kit fitter Do NOT overtighten socket covers as glass may crack or break. Install four 6.5 watt max. medium base LED bulbs (included). IMPORTANT: When you need to replace bulbs, please allow bulb(s) and glass shades(s) to cool down before touching them. socket bulb socket cover 10. Testing Your Fan.
Troubleshooting. Warranty. Problem: Fan fails to operate. Solutions: 1. Check wall switch to fan. 2. Verify that reverse switch is set completely in either direction. 3. Check to be sure fan is wired properly. LIMITED WARRANTY: We warrant this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: We will replace or repair any fan which has faulty performance due to a defect in material or workmanship. Contact us to arrange for return of fan.
LEER ESTAS INSTRUCCIONES Y GUARDARLAS PARA UTILIZACION FUTURA Twist N Click ® Índice de materias: Ensamblaje Rápido No se necesitan herramientas Guía de instalación Sugerencias de seguridad. Pág. 1 Desempaquetado del ventilador. Pág. 2 Inventario de piezas. Pág. 2 Preparación para la instalación. Pág. 3 Instalación del soporte de montaje. Pág. 3 Ensamblaje del ventilador. Pág. 4 Instalación eléctrica. Pág. 4 Colocación de la cubierta decorativa. Pág. 5 Colocación de las aspas. Pág.
SUGERENCIAS DE SEGURIDAD. ADVERTENCIA: Para evitar la posibilidad de una descarga eléctrica, desconectar la corriente en la caja de fusibles principal o el interruptor protector antes de iniciar la instalación del ventilador o antes de repararlo o instalar accesorios. 1. LEER TODAS LAS INSTRUCCIONES E INFORMACIÓN DE SEGURIDAD CUIDADOSAMENTE ANTES DE INSTALAR SU VENTILADOR Y GUARDAR ESTAS INSTRUCCIONES.
1. Desempaquetado del ventilador. Abrir el empaque cuidadosamente. Sacar los artículos del embalaje. Sacar el motor y ponerlo en una alfombra o en el embalaje para evitar rayar el acabado. Guardar la caja de cartón o el empaquetamiento original en caso de que tenga que mandar el ventilador para alguna reparación. Comprobar las piezas del ventilador con el inventario de piezas y verificar que se incluyeron todas. i 2. Inventario de piezas. a a. soporte de montaje. 1 unidad b b. cubierta decorativa.
3,66m - 6,1m (12 pies - 20 pies) 3. Preparación para la instalación. borde del aspa 76cm (30 2,13m pulg.) (7 pies) Para prevenir daño corporal y otros daños, estar seguro de que el lugar en donde va a colgar el ventilador le permite un espacio libre de 2,13m (7 pies) entre las puntas de las aspas y el piso y 76cm (30 pulg.) entre las aspas y cualquier pared u otra obstrucción. Este ventilador es adecuado para habitaciones hasta 37,2 metros cuadrados (400 pies cuadrados).
5. Ensamblaje del ventilador. Ya que esté sujetado el soporte de montaje a la caja de salida y capaz de apoyar el ventilador, usted está listo para colgar el ventilador. Agarrar el ventilador firmemente con las dos manos. Deslizar el tubo por la abertura del soporte de montaje y dejar que se detenga la bola en el soporte de montaje. Girar la bola que sirve para colgar hasta que la ranura de la bola se alinee con la parte saliente del soporte de montaje.
7. Colocación de la cubierta decorativa. Elevar la cubierta decorativa hasta el cielo y permitir que se pegue al soporte de montaje usando los imanes montados en cada lado de la cubierta decorativa. Cuidadosamente despegar la envoltura de plástico alrededor del protector del tubo. Nota: Si por alguna razón fuera necesario bajar la cubierta decorativa, usar cuidado al pasar la cubierta decorativa por el protector del tubo para que no se raye la superficie de metal. 8. Colocación de las aspas.
9. Instalación del juego de luz. Retire las cubiertas de los portalámparas de los portalámparas del conectador para el juego de luz. Fije las pantallas de vidrio a los portalámparas y asegúrelas con las cubiertas de los portalámparas. conectador para el juego de luz No apriete demasiado las cubiertas de los portalámparas, ya que el vidrio podría agrietarse o quebrarse. portalámpara Instalar cuatro bombillas LED de base mediana de 6,5 vatios máx. (incluidas).
Localización de fallas. ADVERTENCIA: El no desconectar el suministro de fuerza eléctrica antes de hacer localización de fallas para cualquier problema de instalación eléctrica puede causar lesiones graves. Problema: El ventilador no funciona. Soluciones: 1. Inspeccionar el interruptor de pared del ventilador. 2. Verificar que el interruptor de reversa del ventilador está en una sola posición, no en medio de las dos. 3. Verificar la instalación eléctrica del ventilador.