Assembly Instructions

ManualsBrandsWinston Porter ManualsBedroom SetsBeagan Platform 5 Piece Bedroom Set

CSK M4 x 32mm

L KEY M4

L KEY M5

CSK M4 x 16mm

JCBC SCREW M6 x 50mm

L KEY M4

JCBC SCREW M6 x 30mm

FLAT WASHER Ø

" x 13mm

SPRING WASHER Ø

Drawer Slat Support

Bed Slat Support

Bed Slat 3Holes

Center Slat With 3 Holes

Drawer Slat

Bed Rail

Bed Slat 2Holes

Qty.

Footboard

Descriptions

Headboard Panel

NO.

1 1

Slat Cover

Headboard Leg Left (L)

Headboard Leg Right (R)

Drawer

Drawer Slat Support Stopper

Part & Hardware List Pack In

Headboard & Footboard

Part & Hardware List Pack In Side

Rail

Part List Pack In Footboard Drawer

Page 1 of 6

ASSEMBLY INSTRUCTION

KING BED

Summary of content (6 pages)

PAGE 1
ASSEMBLY INSTRUCTION KING BED Part & Hardware List Pack In Headboard & Footboard NO.
PAGE 2
ASSEMBLY INSTRUCTION KING BED STEP 1.1: Align and fasten Headboard Leg (2) & (3) to Headboard Panel (1) using JCBC M6 x 30mm (6), Spring Washer Ø14"(7) and Flat Washer Ø14" x 13mm (8) and tighten with L Key M4 (9).
PAGE 3
ASSEMBLY INSTRUCTION KING BED STEP 2.1: Attach the Bed Rail (10) to Headboard Leg. STEP 2.2: Tighten SCREW on Headboard Leg by using L KEY M5 (22) & repeat the same step on Footboard (4). STEP 2.3: Move the bed to the desired position. STEP 2.4: Attach the Drawer Slat (11) each to a Drawer Slat Support (12) and fix with Drawer Slat Support Stopper (17). STEP 2.5: Fix the Drawer Slat (11) to Bed Rail (10) with CSK M4 x 32mm (19). STEP 2.6: Move 'T' Runner at Footboard (4) to Drawer Slat (11). STEP 2.
PAGE 4
ASSEMBLY INSTRUCTION KING BED STEP 3.1: Insert Drawer (23) to Footboard (4) until completely closed. STEP 3.2: Tighten 'T' Runner at Footboard (4) to Drawer Slat (11) with CSK M4 x 16mm (18). STEP 3.3: If Drawer (23) does not close properly,adjust the adjuster at the bottom of Drawer Slat Support (12) up or down until the Drawer (23) closes tightly. STEP 3.1 23 18 STEP 3.2 10 11 STEP 3.
PAGE 5
ASSEMBLY INSTRUCTION KING BED STEP 4.1: Attach the Center Slat (16), Bed Slat (13) to Bed Slat Support (15).Tighten with JCBC M6 x 50mm (20) by using L KEY M4 (21). STEP 4.2: Attach Bed Slat (13) & Bed Slat (14) and tighten to Bed Rail (10) with CSK M4 x 32mm (19). 19 STEP 4.2 10 13 14 16 21 15 20 13 16 15 15 Page 5 of 6 STEP 4.
PAGE 6
ASSEMBLY INSTRUCTION KING BED STEP 5.1: Attach the Slat Cover (5) to top Bed Slat (13 & 14) . STEP 5.2: Close the distance Slat Cover (5) to Footboard (4).Tighten Slat Cover (5) to Wood at Footboard (4) with CSK M4 x 16mm (18). 18 5 STEP 5.2 4 STEP 5.