WBT300
Inhalt Teil 1 Produktvorstellung 2 Teil 2 Leistungsmerkmale 3 Teil 3 Sicherheitshinweise 4 Teil 4 Kurzanleitung 6 Teil 5 Betriebshinweise 9 Teil 6 Installation des USBTreibers 11 Teil 7 Benutzung mit dem Pocket PC 18 Teil 8 Fehlersuche 36 1
Teil 1 Produktvorstellung Übersicht GPS LED: (Grün) Grüne LED leuchtet dauerhaft: Positionsbestimmung nicht abgeschlossen. Grüne LED blinkt: Positionsbestimmung abgeschlossen. Power LED: (Rot) Rote LED blinkt: Akku Ladestatus niedrig. Rote LED leuchtet dauerhaft: Akku wird geladen. Rote LED aus: Akku ist voll aufgeladen. Bluetooth LED: (Blau) Blaue LED aus: BluetoothFunktion ausgeschaltet. Blaue LED leuchtet dauerhaft: Bluetooth ist in Betrieb. Keine Verbindung zu anderem Gerät. Blaue LED blinkt (0,5 Sek.
Teil 2 Leistungsmerkmale Der Wintec WBT300 ist ein Bluetooth GPSEmpfänger mit eingebauter Antenne. Der im Kern verwendete GPS Chipsatz Atmel / ublox ATR 0625 ist für die Navigation, Geochaching, Topographie und andere landwirtschaftliche Zwecke geeignet. Der mini USBAnschluss sowie die BluetoothSchnittstelle ermöglichen eine einfache Verbindung mit anderen elektronischen Geräten.
Unterstützung von NMEA 0183 v2.1 und v2.3, UBX, RTCM Protokollen für den Datentransfer Die mitgelieferte Software “GRays I” vereinfacht die Bedienung. Spritzwasserdicht Mittels Bluetooth kann die Datenübertragung innerhalb einer Reichweite von 10 Metern erfolgen Durch sein Design ist das Gerät vielseitig einsetzbar: für Fahrzeug/persönliche Navigation, Geocaching, Flottenmanagement, AVL, Tracking und Topographie Gewicht ca.
Das eigenmächtige Auswechseln von Teilen des Gerätes und die Umrüstung sind nicht gestattet; ein Zuwiderhandeln kann dazu führen, dass der Gebrauch des Gerätes widerrechtlich ist. Öffnen oder modifizieren Sie den GPS Empfänger nicht, andernfalls kann die Gewährleistung verfallen. Der Betrieb des Gerätes in hochexplosiver Umgebung, wie z.B. beim Bergbau, während des Fluges oder in anderen Gebieten, wo der Gebrauch untersagt ist, ist strengstens verboten.
Packungsinhalt: Wintec WBT300 (Bluetooth GPSEmpfänger), USB Datenkabel, 12V StromAdapter, Software und Treiber CDROM, Kurzanleitung Wintec WBT300 Inbetriebnahme: Zum Einschalten des Gerätes kurzzeitig die PowerTaste drücken. Die Bluetooth und die GPSStatus LED leuchten zur Bestätigung, dass sich das Gerät im normalen Such Modus befindet. Das Gerät beginnt mit der Positionsberechnung. Zum Ausschalten des Gerätes die PowerTaste länger gedrückt halten (ca. 3 Sek.).
Ist das Gerät eingeschaltet und nicht mittels USB oder BluetoothSchnittstelle verbunden, schaltet der WBT300 nach 5 Minuten in den Energiesparmodus, bis es wieder verbunden wird. Benutzung der USBSchnittstelle: Zuerst muss der USBTreiber installiert werden. Nachdem Sie das Gerät mit dem USBPort Ihres Computers verbunden haben, schalten Sie es ein und legen Sie es an einen Platz, wo ein optimaler Empfang des GPSSignals gewährleistet ist.
Laden des Akkus: Das Aufladen kann mithilfe des mit dem Computer verbundenen USBDatenkabels, mittels Netzteil oder KfzZigarettenanzünder erfolgen. Wenn sich der WBT300 im Betriebsmodus befindet, wird ebenfalls aufgeladen.
Teil 5 Betriebshinweise Ist der WBT300 eingeschaltet, führt er einen Selbstcheck durch. Bluetooth und GPS sind betriebsbereit, wenn die Bluetooth LED (Blau) und die GPS LED (Grün) leuchten. Der GPSEmpfänger beginnt automatisch mit der Positionsbestimmung und protokolliert die Daten. Bei wolkenlosem Himmel benötigt das Gerät ca. 34 Sekunden bis zur ersten Positionsbestimmung. (Wenn die Daten im internen Speicher gültig sind, dauert es nur 433 Sekunden).
Nach der Positionsbestimmung überträgt der WBT300 folgende Daten via Schnittstelle: geografische Breitengrade geografische Längengrade Höhe Geschwindigkeit Datum, Uhrzeit (UTCZeit) Satellitenstatus Empfangsstatus 10
Teil 6 Installation des USBTreibers Legen Sie die mitgelieferte „GPS Application“ CDROM ein. Sollte diese nicht automatisch starten, gehen Sie auf „Arbeitsplatz“ und klicken das entsprechende Laufwerk mit einem Doppelklick an.
Wenn das Installationsprogramm gestartet ist, wählen Sie „GRays I“ aus und können nun entweder das „GRays I Tool (PC)“ für den PC oder das „GRays I Tool (PPC)“ für den Pocket PC installieren. Bei der Installation des PC Programms werden die USB Treiber automatisch in den „GRaysI“ Installationsordner abgelegt (Beispiel: C:\Programme\GRaysI\USB Driver).
Verbinden Sie den WBT300 mithilfe des USB Datenkabels mit dem USBPort des Computers. Der Computer prüft automatisch das Gerät und sucht nach den entsprechenden USBTreibern. Nachdem das Gerät verbunden ist, führen Sie die folgenden Schritte aus. Klicken Sie auf “Software von einer Liste oder bestimmten Quelle installieren” und dann auf „Weiter“.
Wählen Sie im nächsten Schritt „Diese Quellen nach dem zutreffendsten Treiber durchsuchen“ und „Folgende Quellen ebenfalls durchsuchen:“ aus. Mit einem Klick auf „Durchsuchen“ können Sie nun Ihren G Rays I Installationsordner angeben. Der benötigte USB Treiber befindet sich im Installationsordner des GRays I Programms.
Wird bei der USB Treiber Installation der folgende Warnhinweis angezeigt, klicken Sie bitte auf “Installation fortsetzen”.
Die Installation ist abgeschlossen. Klicken Sie auf „Fertig stellen“.
Um den Installationsstatus zu prüfen, gehen Sie über „Start“ → „Einstellungen“ → „Systemsteuerung“ → „System“ → „Hardware“ auf den “Geräte Manager”. Wie in der Abbildung dargestellt ist der USBTreiber erfolgreich auf dem PC installiert. Es wird ebenfalls angezeigt, dass das Gerät dem COM 5 zugewiesen wurde. Immer wenn der WBT300 in Zukunft mit dem gleichen USBPort des Computers verbunden wird, stellt COM 5 die Schnittstelle für die Datenkommunikation her.
18
Teil 7 Benutzung mit dem Pocket PC Benutzen Sie den WBT300 mithilfe des Pocket PC. Sie müssen hierfür das „GRays I Tool (PPC)“ auf Ihrem Pocket PC installiert haben. Um eine Verbindung mit Bluetooth herzustellen, führen Sie bitte die folgenden Schritte durch. Hinweis: Eine interaktive Installationshilfe für gängige Windows Mobile Betriebssysteme finden Sie auf der Webseite http://www.wintecgps.
1. Schritt: BluetoothVerbindung mit dem Pocket PC herstellen: 1 Tippen Sie auf der Taskleiste des Pocket PC auf das „BluetoothSymbol“, um das BluetoothMenü anzuzeigen. Wählen Sie ”Bluetooth EIN”, um Bluetooth zu aktivieren.
2 Tippen Sie erneut auf das „BluetoothSymbol“ und wählen Sie den ”Bluetooth Manager” aus.
3 Tippen Sie vom Bluetooth Manager aus auf ”Neu”, um nach BluetoothGeräten in der Nähe zu suchen.
4 Tippen Sie auf “Bluetooth Geräte durchsuchen” und dann auf Weiter”.
5 Wenn der Pocket PC den WBT300 gefunden hat, tippen Sie bitte einmal auf das neue Symbol „BT GPS“ und dann auf „Weiter“.
6 Wählen Sie den “SPP slave” Dienst, und die „Verschlüsselte Verbindung verwenden“ aus und tippen dann auf “Weiter”, um eine Verknüpfung damit herzustellen.
7 Tippen Sie auf “Fertig”, um die Auswahl abzuschließen.
8 Tippen Sie dann länger auf das Symbol “BTGPS: SPP Slave” aus Ihren Verknüpfungen und wählen Sie die Option “Verbinden“ um die Verbindung herzustellen.
9 Sie werden in diesem Schritt nach einem Kennwort gefragt. Dieses Kennwort lautet „0000“. Wenn die Verbindung erfolgreich hergestellt wurde, wechselt das Symbol auf grün.
2. Schritt: Benutzung des GRays I Tool (PPC) für Pocket PC Mithilfe des GRays I Tool (PPC) können Sie sich Ihre Position nach Breitengrad, Längengrad, Geschwindigkeit, Kurs und Höhe anzeigen lassen. Vergewissern Sie sich, dass das GRays Tool (PPC) gemäß der Beschreibung auf der „Application CD“ auf Ihrem Pocket PC installiert ist. 1 Tippen Sie auf Start”, um vom Startmenü aus Programme” zu wählen.
2 Wählen und starten Sie aus Ihrem Programm Menü das „GRays Tool“.
3. Von dem Registerreiter ”Connect Setting” aus, können Sie nun den Bluetooth COMPort auf Ihrem Pocket PC unter ”Select GPS Port” auswählen und klicken dann auf “Connect“ um beide Geräte miteinander zu verbinden. Meistens ist der Bluetooth COMPort bei vielen Pocket PC Geräten einer zwischen 5 und 8.
Wählen Sie dann, wenn sich ein Bluetooth Manager Fenster öffnet, das Symbol “BTGPS“.
4.
5. Merkmale der weiteren Schaltflächen: “Action Mode” ReStart, Einstellen der Update Rate (Hertz), Einstellen der SBAS Konfiguration (WAAS/EGNOS).
“NMEA” Einstellungen der NMEAAusgabe. Hier können Sie einen NMEADatensatz auswählen den Sie aktivieren möchten.
“Satellite” Anzeige der Satellitendaten “Sky Plot” Anzeige der Satellitenverteilung.
6. Wenn eine neue Konfiguration erfolgt ist, z.B.: Änderung der Ausgaberate des NMEADatensatzes nach Uhrzeit, GPS UpdateRate oder Aktivierung von SBAS (WAAS/EGNOS), erscheint unter “Connect Setting”, “NMEA” und “Action Mode” die Schaltfläche „Save Configuration“. Dies bedeutet, dass Sie die internen Einstellungen speichern und diese dann im GPSEmpfänger geändert haben. Wenn sie nicht gespeichert werden, bevor GRays Tool ausgeschaltet wird, entspricht die Konfiguration wieder den früheren Einstellungen.
Teil 8 Fehlersuche Unter folgenden Bedingungen kann das GPSSignal schwächer werden: Wenn das Fahrzeug in einen Tunnel fährt. Das GPSSignal wird linear zur Erde gesendet und ist in dieser Situation blockiert. Die GPSSatellitenerfassung wird in der Nähe von hohen Gebäuden oder in dichtem Wald schwächer. Obwohl WBT300 ein schwaches GPSSignal empfangen kann, könnte die Positionsgenauigkeit beeinträchtigt werden.
Manche Navigationssoftware kann vom NMEA 0183 nur die vom Logger angegebene Breiten und Längengrade dekodieren. Es sind keine Höhendaten verfügbar, somit wird bei der Positionsbestimmung des Fahrzeugs nicht angezeigt, ob es sich unter oder auf einer Brücke befindet.
Vor dem Anschluss des Gerätes an den USBPort des Computers, muss der USBTreiber installiert werden. Vergewissern Sie sich, dass der richtige COMPort benutzt wird. Erfolgt die Trennung von Pocket PC und GPS auf unnormale Weise, bleibt der Pocket PC oder das Programm stehen. Versuchen Sie, die BluetoothVerbindung auf die übliche Weise zu trennen.