Installation Set-up Interface cables Revision 18 Company Confidential Proprietary
Before you start! X10DR has been designed to allow simple connectivity to most radio models from those dating back from the 90’s to the most current digital models from most professional radio manufacturers. Understanding the basic connectivity will allow you to successfully connect to just about any wireless radio device, or to allied wired radio control consoles. The following describes the pin out connectivity of the X10DR mobile charger’s 15 pin DB15 connector.
Pin 7. Emergency Out: This output is intended to connect to the host mobile radio’s emergency input. It is normally provides an active switched ground (<50mA sink) but can be jumpered to be active open circuit. The time held low (or high) is the exact time that the user presses the Emergency button. This output could be used for other functions such as to trigger the panic function of a grammed for such. Pin 8.
Internal Jumpering (Original models) - der “blob jumpers” are provided to allow compatibility with different mobile radio types. SMD type hand soldering.) ternal PCB. Take extreme care when handling the PCB to prevent damage by electrostatic discharge (ESD) or to internal wiring. Re-assemble carefully making sure to not damage wiring.
Internal dip switch setting ( Post Apr 2014) These dip switch settings are provided to allow compatibility with different mobile radio types. ternal PCB. Take extreme care when handling the PCB to prevent damage by electrostatic discharge (ESD) or to internal wiring. Re-assemble carefully making sure to not damage wiring.
Set Up - Basic Requirements Radio Programming - VERY IMPORTANT For correct X10DR operation, the host mobile radio on some occasions will require reprogramming (via its associated FPP/CPS etc) to enable correct functionality. Read carefully this instruction document to get a complete understanding of the interfacing requirelike PTT, COR (channel busy), emergency trigger and audio level settings to be accessible on the radios rear interface connector.
Mobile charger DB15 connector Typical wiring diagram (New Generic cable color scheme shown) DB15 connector User supplied manual off/on (if desired/required) connects to D shell BLK BRN RED ORG YEL DRK GRN BLU PUR GRY BLK-WH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Radio connector Shield Switched B+ sense from radio or manual off/on switch Ext Mic audio to radio - default* 80mV) Mic Lo to radio Received audio input from radio - default >400mV)** Power ( nominal +12V) Ext PTT output to radio (active: sw grd
XMC-GEN Interface cable - Original generic cable version. Note: different wiring colour scheme.
XMC-GEN Interface cable - Current version: for any mobile V1 DB15 F BLK BRN RED ORG YEL DRK GRN BLU PUR GRY 1 BLK-WH 13 Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 3 4 5 6 7 8 9 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio DC/ Digital Ground Remote/ footswitch/Handle bar PTT 150cm WG*15C +ADB unstripped Drain BLK-WH(new) Red "J1" FEMALE, 15-CONTACT D-SUB CONNECTOR X10DR ¥ In-line fuseholder 1A FB fuse Company C
XMC-XTL Interface cable : for Motorola APX/XTL series V1 RED 22AWG with fuseholder Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 14 Ext PTT to radio Emergency out to radio (N/C) COR/ Channel activity from radio DC/ Digital Ground 16 15 13 1 Remote/ footswitch/Handle bar PTT BLK/WH 13 Emergency operation on older XTL mobiles BLK/WH Connector shown for reference o
XMC-MCS Interface cable V0 DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 14 10 11 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground DB25 -M Connector Notes: 13 8 4 Program Pin 21 for PTT Program Pin 8 for “car radio mute”.
XMC-M16 Interface cable : for Motorola MTM800/GM360/MCX/PM400/CDM etc.
XMC-M25 Interface cable V0 DB25 -M Connector DB15 F 1 3 4 5 6 7 8 9 Need to remove shorting jumper on radio TIB to enable Emergency function.
XMC-M26T Interface cable : for Motorola Tetra MTM5400 series V1 ( If you use XMC-M26 cable, you must move Mic Hi and Mic Lo RED 22AWG with fuseholder Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 Drain/shield 7 13 16 14 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio DC/ Digital Ground 17 N/C 8 Remote/ footswitch/Handle bar PTT BLK/WH 13 (do
XMC-M26 Interface cable : for Motorola Trbo XPR and DM3600 etc series V0 RED 22AWG with fuseholder Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 7 11 14 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio DC/ Digital Ground 17 8 Remote/ footswitch/Handle bar PTT BLK/WH 13 BLK/WH Ground 18 Ground 20 GP5_6 22 GP5_7 24 GP5_8 26 Ign Sense
XPR/DM3600 Programming info V0 Company Confidential Proprietary
XMC-K25 Interface cable V1 RED 22AWG with fuseholder Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 8.2k 17 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 4 8# X10DR ¥ Notes: Radio pins 4, 8, & 24 need programming on NX700 models and some other Kenwood models.
NX700/800 Programming info V0 Company Confidential Proprietary
XMC-K15 Interface cable : for Kenwood 15 Pin radios/ KCT-19 cable V0 RED 22AWG with fuseholder Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 SHIELD/DRAIN 7 5 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 8 15 11 6 Remote/ footswitch/Handle bar PTT BLK/WH 13 Program Radio FNCs tied to Molex pins Pins 8: PTT Pin 11: TOR
XMC-K15D Interface cable V0 DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 5 15 4 1 6 7 8 15 8.
XMC-K15 Interface cable : for Kenwood 15 Pin radios using KCT-39 cable/TK7160 etc V0 NOTE: The XMC-K15 Cable is factory set up for KCT-19 Kenwood interface cable. To use with KCT-39 you must rewire the XMC-K15 molex 15 pin connector as per the following: Additionally, you must move two wires in connector CN3 of Kenwood’s KCT-39 cable. (see insert) Note: X10DR must be set for 200mV mic audio out (pin2) - may require use of XPK programmer.
XMC-K15S Interface cable V0 : requires use of external speaker DB15M D-SUB DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1 BLK/WH 13 Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 3 4 5 6 7 8 9 8.
XMC-T15 Interface cable : for Tait TM/7000/8000/9000 Series V0 RED 22AWG with fuseholder Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 8 14 15 13 4 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 5 10 15 Remote/ footswitch/Handle bar PTT BLK/WH 13 Program Radio connector 12- GPIO1 PTT in 10- GPIO Busy out 5 - GPIO Emer
TM9000 Programming info V0 Company Confidential Proprietary
XMC-i15 Interface cable : for Icom OPC-1939 adaptor cable V1 DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 15 13 3 7 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 4 - I/O COR out 7 - AF Audio out 11- I/O Emerg In 14 - Ext PTT BLK/WH 150cm WG*15C +ADB unstripped WH Red "J1" FEMALE, 15-CONTACT D-SUB CONNECTOR X10DR ¥ * or Purple ** or Pu
XMC-i25 Interface cable : for Icom IC-F5061/9511 etc V1 RED 22AWG with fuseholder 1A FB fuse Battery S DB15 F BLK BRN RED ORG YEL DRK GRN BLU PUR GRY 1 BLK-WH 13 Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 3 4 5 6 7 8 9 11 8 7 9 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 19 15 17 14 Remote/ footswitch/Handle bar PTT Program Radio connector pin 15: Emergency Input if available.
XMC-HXG Interface cable : for Harris XG100 High tier mobiles V1 RED 22AWG with fuseholder 1A FB fuse Battery S DB15 F BLK BRN RED ORG YEL DRK GRN BLU PUR GRY 1 BLK-WH 13 Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 3 4 5 6 7 8 9 1 5 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 18 (Needs program for PTT) 7 Remote/ footswitch/Handle bar PTT BLK/WH Use XG100 RPM to select I/O and function requ
XMC-V25 Interface cable : for Vertex VX5500 etc High tier mobiles V0 RED 22AWG with fuseholder S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 14 13 17 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 11 7 & 18 Remote/ footswitch/Handle bar PTT BLK/WH 13 BLK/WH 150cm WG*15C +ADB unstripped BLK/WH Red "J1" FEMALE, 15-CONTACT
XMC-V15 Interface cable : for Vertex 15 pin lower tier mobiles V0 RED 22AWG with fuseholder 1A FB fuse S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1 BLK/WH 13 Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 3 4 5 6 7 8 9 4 1 3 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 6 14 13 15 Remote/ footswitch/Handle bar PTT BLK/WH 150cm WG*15C +ADB unstripped BLK/WH Red "J1" FEMALE, 15-CONTACT D-SUB
XMC-C26 Interface cable : for Cassidian TMR880/i mobiles V1 DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 3*&4* 18 Remote/ footswitch/Handle bar PTT BLK/WH 13 *programmable radio pins 1:No action 5V 2/:Emerg In 3/Rx Activity 4/Call incoming 1* BLK/WH R1 100K R2 1K Q1 MOSFET P 150cm 27K K D1 1
XMC-SRM Interface cable: for Simoco SRM 9000 series mobiles (adds X10DR Interface cable to an existing SRM power cable) DB15 F BLK Drain connects to shell Switched B+ from radio Audio out to radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 BLK-WH GRN 3 4 5 6 7 8 9 WH 13 BRN* BRN-WH** RED RED-WH ORG YEL Drain connects to shell 14 15 Ext PTT to radio Emergency input COR/ Audio unmute from radio DC/ Digital Ground 7 3 8 ORG Remote/ footswitch/Handle bar PTT 22# BLK 22# RED RED PUR
SRM9000 Programming info V0 Company Confidential Proprietary
XMC-SRG Interface cable: for Sepura SRG TETRA series mobiles (add X10DR to an existing SRG power cable) V1 DB15 F BLK Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 BLK-WH BRN* BRN-WH** RED RED-WH ORG YEL GRN RED 3 4 5 6 7 8 9 4 7 6,8 &SH 5 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 7 15 14 100K RED 26AWG RED PUR 150cm DB15 -HD-M D-SUB WG*15C +ADB 26 AWG X10DR 13 6 8 3 SPK Conn GRN YLW
SRG3900 Programming info V0 Company Confidential Proprietary
BLK BRN RED ORG YEL GRN BLU PUR GRY Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio DC/ Digital Ground BLK/WH 13 24 12 13 21 ( program for Ext PTT?) 23 ( program for Emergency Input?) 22 ( program for COR/radio unmute?) 1 BLK/WH 150cm Figure 19 - Remote Mount Extended Option Accessory Cable 19B802554P7 WG*15C +ADB Drain WH Red In-line fuseholder 1A FB fuse "
XMC-H26 Interface cable : for Hytera MD68x Tetra & 78x DMR mobiles V1 RED 22AWG with fuseholder Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 4 7 17 8 Ext PTT to radio Emergency out to radio COR/ Audio unmute/Channel activity DC/ Digital Ground 16* 14 3* Remote/ footswitch/Handle bar PTT BLK/WH 13 *programmable radio pins 16: PTT : Active Lo 3: Rx Activity (spkr
XMC-T26 Interface cable : for Teltronic MDT400 mobiles (Draft) V1 RED 22AWG with fuseholder BLK BRN RED ORG YEL GRN BLU PUR GRY Battery S DB15 F 1A FB fuse Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 8* 13 9 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 5 Remote/ footswitch/Handle bar PTT BLK/WH13 *Requires pressing (phonebook) + (9) + (7) then setting audio accessory to Handsf
XMC-G25 Interface cable V0 RED 22AWG with fuseholder 1A FB fuse Battery S DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY 1 BLK/WH 13 Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 3 4 5 6 7 8 9 3 11* 6 9 Remote/ footswitch/Handle bar PTT WH 150cm WG*15C +ADB unstripped WH Red X10DR Notes: 8 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground "J1" FEMALE, 15-CONTACT D-SUB CONNECTOR DB25 -Female Con
XMC-R15 Interface cable : for RELM BENDIX KING GMH/DMH mobiles V1 DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 5 11 6 Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground ? emergency input BLK/WH 150cm WG*15C +ADB unstripped WH Red "J1" FEMALE, 15-CONTACT D-SUB CONNECTOR X10DR * or Purple ** or Purple /White In-line fuseholder 1A FB fuse ¥
XMC-R25 Interface cable V0 DB15 F BLK BRN RED ORG YEL GRN BLU PUR GRY Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio 1 3 4 5 6 7 8 9 6.8k Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio/TOR DC/ Digital Ground 9 Notes: Programradio Pin 23 for “cor”.
XMC SERIES CABLES - ALTERNATE WIRING COLORS DB15 F CURRENT BLK 1 BLK-WH BRN* 3 BRN-WH** 4 RED 5 RED-WH 6 ORG 7 YEL 8 GRN 9 WH 13 Drain connects to shell Switched B+ from radio Ext Mic Hi Mic Lo to radio Received audio from radio Ext PTT to radio Emergency out to radio COR/ Audio unmute from radio DC/ Digital Ground Remote/ footswitch/Handle bar PTT * or Purple ** or Purple /White DB15 F FUTURE X10DR BLK BRN RED ORG YEL DRK GRN BLU PUR GRY 1 BLK-WH 13 3 4 5 6 7 8 9 Drain connects to shell Switc
MOTORCYCLE INSTALLATIONS X10DR has been designed for Motorcycle installations. By ordering either the X10DR-XX1 or the XU1 model with the XHC As many organisations globally have adopted their own wiring standards for the helmet audio “down cable”, WCL has a custom cable service available to allow custom professionally manufactured interface cable to plug between the X10DR’s 6 pin Hirose connector and your existing helmet wiring.
MOTORCYCLE INSTALLATIONS - Continued X10DR Hirose input-M/C Bridged audio X10DR Hirose input Typical Interface cable shield / GRD shield / GRD 4mm 6 4mm curly cable Mic Hi Red PTT PTT Black GRD Spk Hi Spk Lo White Blue quick disconnect If desired 1 5 6 6 1 5 2 3 4 4 1 6 2 4 3 Mic Hi 1 PTT PTT 4700 ohm 5 3 Mic Hi switched 3.
TROUBLESHOOTING requires for correct operation. Most problems getting the X10DR to work with your radio usually come down to simple things easily overlooked. These include: 1/ Forgetting to program or jumper your radio’s interface connector to provide the REQUIRED function input/output. - these may include: enabling Emergency input with active low, enabling COR with active low output, Setting radio RX audio to be muted when radio is squelched, setting External Mic input for analog audio, etc.
trademarks of Wireless Corporation Limited.
