Cut Sheet
3
Catalog No./Item Description/Specifications
6001A Coupling –
For joining lengths
of 6000B.
G6000WC Wire Clip –
For holding conductors
in place. Use only with undivided
6000 Series Raceway.
G6001DA
†
Divider Clip – For holding G6000DA
Divider in place to divide raceway
into 1/3, 1/2, or 2/3 compartments.
6000 Raceway divided into
1/3 compartments will not
accept devices.
G6001TX Converter Coupling – For converting
6011TX or 6017TX into a tee or cross.
For tee, one required; for cross,
two required.
G6008A C-Hanger – For suspending 6000 or
4000 Raceway from structural ceiling.
Designed for use with 3/8" (9.5mm)
rod. Hangers should be installed no
more than 4
'
(1.2m) apart along
raceway run. Can be bolted back-to-
back for dual runs of 4000, 6000, or
to a G3008C for combined runs with
3000 Raceway.
V4000C075/ Pre-Cut Cover 7.5" (191mm) –
G4000C075* For mounting devices on 12"
(305mm) centers with 4047 Series
Cover Plates.
V4000C135/ Pre-Cut Cover 13.5" (345mm) –
G4000C135 For mounting devices on 18"
(457mm) centers with 4047 Series
Cover Plates.
V4000C195/ Pre-Cut Cover 19.5" (495mm) –
G4000C195 For mounting devices on 24"
(610mm) centers with 4047
Series Cover Plates.
V4000C315/ Pre-Cut Cover 31.5" (800mm) –
G4000C315 For mounting devices on 36"
(915mm) centers with 4047 Series
Cover Plates.
Catalog No./Item Description/Specifications
V6000B-10 Base – .060" (1.5mm) galvanized
G6000B010 steel. Packed two 10
'
(3m) lengths
per carton. Base has two 9/32"
diameter trade size KOs 1 1/4"
(32mm) from each end and on
centers of approximately
18" (457mm) throughout.
V6000C* Cover – 040" (1.0mm) galvanized
G6000C* steel. Packed four 5
'
(1.5m)
per carton.
G6000DA
**
Divider – .040" (1.0mm)
galvanized steel. One side painted
buff primer to provide identification
of compartments. Packed four 5
'
(1.5m) lengths per carton.
660B
Base Cutter – Portable base
cutter. Steel constructed provides
clean and easy square cuts.
Manual operation required.
660BDK
Replacement Blade Kit –
Replacement blade and die
set for 640B Cutter.
640C
Cover Cutter – Portable cover
cutter. Steel constructed
provides clean and easy square
cuts. Manual operation required.
640CDK
Replacement Blade Kit –
Replacement blade and die
set for 640C Cutter.
IWE-S
Spray Paint – Used for touching
GWE-S
up large areas. Contains 12 oz.
of paint.
IWE-P
Touch-Up Paint Pen – Used for
GWE-P
touching up small areas.
Contains 0.3 oz. of paint.
6000 Series Raceway Ordering Information
3 9/16"
(90mm)
4 3/4"
(121mm)
3 1/4"
(83mm)
4 3/4"
(121mm)
* 4000C and 6000C are compatible with 4000B and 6000B Raceway.
** G6001DA Divider Clips are required to hold divider in place.
NOTE:
Can only be shipped via
ground transportation.
1 1/2"
(38mm)
7 7/8"
(200mm)
6 7/8"
(175mm)
2 1/2"
(64mm)
3 5/16"
(84mm)
3"
(76mm)
2 3/8"
(60mm)
3"
(76mm)
2 7/8"
(73mm)