Cut Sheet

3
Catalog No./Item Description/Specifications
G4000D Divider – 0.040mm galvanized
s
teel. Packed ten 5' [1.525m]
lengths 50' [15.24m] per carton.
4001DA Divider Clip (Plated) –
Required for holding G4000D
Divider in place. Use one
every 2 1/2' [.762m].
4001A Coupling (Galvanized Steel
Plated) – For joining lengths
of G4000B. Sold in pairs.
S4010B Blank End Fittings – For
closing open end of S4000
Base. Use where no end
feeding is required.
S4010B1 Blank End Fittings – For
closing open end of undivided
S4000 Base where one end
feed is required. Includes one
1/2" – 3/4" trade size KO.
S4010B2 Blank End Fittings – For
closing open end of S4000 Base
where end feeds are required.
Includes two 1/2" – 3/4"
trade size KOs.
S4010D Entrance End Fitting – Has
concentric 1/2" and 3/4" trade
size KOs on end, sides and
bottom. Use punch kit for trade
size up to 1 1/4". Removable
divider furnished. Two No.10-32
ground terminals provided.
G6008A C-Hanger – For suspending
S4000 Raceway from structural
ceiling. Designed for use with
3/8" [9.5mm] rod. Hangers should
be installed no more than
5' [1.525m] apart along raceway
run. Can be bolted back-to-back
for dual runs of 4000.
cu
C
atalog No./Item Description/Specifications
S4000B Stainless Steel Base – 1 3/4" x
4 3/4" x 10' [44mm x 121mm x
3.05m]. Base has two .260"
[7mm] dia. KOs 12" [3.05m]
from each end and on centers
of approximately 24" [610mm]
t
hroughout. Base may be
divided (field installed).
S4000BSP Stainless Steel Base –
C
ustomer specified maximum
length is 10' [3.05mm]. Base
has two .260" [7mm] dia.KOs
on centers of approximately 24"
[610mm] throughout. Base
may be divided (field installed).
Stainless Steel Covers for S4000 Raceway
S4000C 5" [1.525mm] Cover – 5"
[1.525m] lengths.
S4000C075 7 1/2" [191mm] Cover – For
mounting 4 1/2" [115mm] device
plates on 12" [305mm] centers.
S4000C135 13 1/2" [343mm] Cover – For
mounting 4 1/2" [115mm] device
plates on 18" [274mm] centers.
S4000C090 9" [229mm] Cover – For
mounting 9" [229mm] device
plates on 18" [274mm] centers.
S4000C195 19 1/2" [456mm] Cover – For
mounting 4 1/2" [115mm] device
plates on 24" [610mm] centers.
S4000C150 15" [343mm] Cover – For
mounting 9" [229mm] device
plates on 24" [610mm] centers.
S4000315 31 1/2" [800mm] Cover – For
mounting 4 1/2" [115mm] device
plates on 36" [915mm] centers.
S4000C270 27" [686mm] Cover – For
mounting 9" [229mm] device
plates on 36" [915mm] centers.
S4000C435 43 1/2" [1106mm] Cover – For
mounting 4 1/2" [115mm] device
plates on 48" [1220mm] centers.
S4000C390 39" [991mm] Cover – For
mounting 9" [229mm] device
plates on 48" [1220mm] centers.
S4000CSP Custom Cover – Pre-cut lengths
to customer specifications.
Maximum length is 5' [1.525m].
S4000 Stainless Steel Raceway Ordering Information
1
17/32"
[
39mm]
1 3/4"
[44mm]
4
3/4"
[
121mm]
1
"
[
25mm]
4 1/2"
[114mm]
1
1/2"
[
38mm]
1
1/2"
[
38mm]
2 1/2"
[64mm]
4001DA Divider Clips are required
t
o hold divider in place.