WPS-700-DOM-A-WH WPS-700-DOM-A-BL DOME CAMERA INSTALLATION MANUAL Review manual thoroughly before installation. Retain for future reference.
WPS-700-DOM-A Installation Manual CONTENTS Safety Instructions............................................................................... 4 Features............................................................................................... 5 Package Contents............................................................................. 6 Installation Instructions....................................................................... 6 Set-Up............................................................
WPS-700-DOM-A Installation Manual SAFETY INSTRUCTIONS This information is provided to ensure your safety and to prevent physical or financial loss. Please read this document carefully before installing and operating the camera. 1. Handle with care. Use caution when handling to avoid damage to sensitive internal components. 2. Do not install camera under extreme temperatures. This camera only operates under temperature conditions between 14˚F ~ 140˚F. 3.
WPS-700-DOM-A Installation Manual FEATURES • 1/3” Sony Super-HAD II CCD The Sony Super HAD II CCD is ideal for low lux illumination, resulting in a clear and crisp image. • Varifocal Auto-Iris Lens This camera features a varifocal lens with a focal length of 2.8-10 mm. The auto-iris function intuitively manages the amount of light passing through the lens for consistent image brightness.
WPS-700-DOM-A Installation Manual PACKAGE CONTENTS (1) Camera (1) AC/DC plug (3) Screws (3) Wall fasteners (1) 3mm Allen Key (1) Foam gasket Manual NOTE 1: A POWER SUPPLY IS NOT INCLUDED WITH THIS CAMERA. The PS-12DC-1A is recommended. NOTE 2 : A Silica Gel package is mounted inside the dome housing. This package should remain inside the housing after installation. INSTALLATION INSTRUCTIONS 1.
WPS-700-DOM-A Installation Manual 4. Use the provided foam gasket as a template to pre-mark mounting hole locations. Position the camera base at the desired location and use the provided screws to attach the camera base to the wall or ceiling. 5. Using the supplied AC/DC plug, connect the power supply jack to 12-30 VDC or 24 VAC and the BNC Video Output to the desired video line.
WPS-700-DOM-A Installation Manual SET-UP Operating the OSD Menu • To view the OSD, the camera must be connected to a display monitor. OSD Menu Button • The button found on the rear circuit board of the camera provides five separate actions: UP, DOWN, EXIT, ENTER and MENU. • Press the button to enter into the OSD MENU page. • Press UP, DOWN, EXIT (Left) or ENTER (Right) to select items on the menu and begin configuration.
WPS-700-DOM-A Installation Manual OSD Menu Structure cont.
WPS-700-DOM-A Installation Manual OSD Menu Structure cont. (bold indicates factory preset) WHITE BAL ATW COL-ROLL PUSH MANUAL COLOR TEMP INDOOR, OUTDOOR BLUE -100~100 (0) RED -100~100 (0) INITIAL SET PREVIOUS 3D-DNR ON, OFF DNR LEVEL 1~100 (24) DESTINATION 0-63 (47) GLOBAL MOVEMENT ON, OFF PREVIOUS EFFECTS DZOOM MODE ON, OFF X1~X6.
WPS-700-DOM-A Installation Manual SPECIAL ITS MODE ON DAY SHUTTER OFF 1/1600, 1/2500, 1/5000, 1/7000, 1/10,000, 1/30,000, 1/50,000, 1/90,000, OFF, A.FLK, 1/160, 1/250, 1/500, 1/700, 1/1000 AGC OFF, LOW, MIDDLE, HIGH LICENSE PLATE ON CONTRAST 0 ~100 (50) PREVIOUS OFF OUTPUT LEVEL 64 ~64 (0) TONE 1 ~64 (0) PREVIOUS NIGHT SHUTTER 1/1600, 1/2500, 1/5000, 1/7000, 1/10,000, 1/30,000, 1/50,000, 1/90,000, OFF, A.
WPS-700-DOM-A Installation Manual OSD MENU SETTINGS The camera menu allows for the adjustment of settings to obtain optimal image clarity and color realism. Note : If there is a “ ” symbol after the option, enter into the subdirectory to adjust more settings. CAMERA NAME SETTING The CAM NAME provides the ability to set a camera title to appear on-screen. 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.
WPS-700-DOM-A Installation Manual EXPOSURE AGC (Auto Gain Control) Setup AGC mode automatically amplifies the video signal during low light conditions. • Adjust the AGC by selecting OFF, LOW, MIDDLE, or HIGH. Please note that signal noise is slightly higher when AGC is enabled. AGC SHUTTER SENSE-UP INITIAL SET PREVIOUS HIGH AUTO AUTO X8 SHUTTER Setup Shutter setup allows for control of the electronic shutter speed.
WPS-700-DOM-A Installation Manual DAY/NIGHT • Set the DAY/NIGHT value to AUTO, DAY, NIGHT, or EXT based on the installation application. • DAY: The camera remains in color mode all of the time. 1. CAM NAME 2. LENS 3. EXPOSURE 4. DAY/NIGHT 5. WDR/BLC/ECLPS 6. WHITE BAL 7. 3D-DNR 8. EFFECTS 9.SPECIAL 0. EXIT OFF DC IRIS DAY WDR ATW ON RET • NIGHT: The camera remains in black and white (B/W) all of the time.
WPS-700-DOM-A Installation Manual EXT Setting By selecting the EXT value in the Day/Night IR MODE OFF IR DEST 32 -------|-------Mode and pressing MENU, you can enter into PREVIOUS a subdirectory to adjust the IR WDR LEVEL and IR WDR DEST. • IR MODE: The IR level can be switched to ON or OFF. • IR DEST: IR Destination is used to spread the IR light to evenly fill the scene with the same IR intensity. • PREVIOUS: Return to previous page.
WPS-700-DOM-A Installation Manual ECLIPSE Setting The ECLIPSE function is used to cut off exceptionally bright light, such as headlights of a vehicle. Zones and sensitivity can be adjusted based on the scene. • AREA SETTING: Up to 16 programmable areas can be set. Press ENTER and EXIT to select areas. Press UP or DOWN to turn the areas ON or OFF. Press MENU to return to previous page.
WPS-700-DOM-A Installation Manual • PUSH: This function is ideal for an environment with the predominance of a single color. For example, when used in a casino and the camera is pointed to a green table, the color would be inaccurate and the overall tone of the picture would be too red. This mode compensates the white balance and offers a more accurate color. To set the PUSH function, select PUSH and zoom the camera to a sheet of white paper located in the scene.
WPS-700-DOM-A Installation Manual <3D-DNR MENU> • DNR LEVEL: User-selectable from 1 to 100. The higher the value, the more obvious DNR performance. DNR LEVEL 24 -----|----------DESTINATION 47 -----------|----GLOBAL MOVEMENT OFF PREVIOUS • DESTINATION: User-selectable from 0 to 63. The higher the value, the brighter the image. • GLOBAL MOVEMENT: This function reduces the object-blurred phenomenon when an object is in motion. • PREVIOUS: Return to previous page.
WPS-700-DOM-A Installation Manual COLOR ADJUST Adjust the color of the image. INITIAL SET Return to factory default setting. PREVIOUS Return to previous page. SPECIAL ITS MODE Intelligent Traffic System Mode allows for setup of the camera in DAY and NIGHT modes to better see license plates in bright light conditions typically caused by car head lamps. Settings adjust the speed of the shutter and AGC based on environmental conditions.
WPS-700-DOM-A Installation Manual PRIVACY MASK Setting Privacy Mask configuration allows for masking of up to 8 “surveillance-free” zones in the picture. For example, this may be used for a camera that has a neighbor’s window in part of the scene. Set PRIVACY MASK to ON to enter into the subdirectory.
WPS-700-DOM-A Installation Manual L/L SYNC Line Lock Sync is used to reduce picture “roll” when the camera is connected to an AC power supply and its picture is switched with other cameras on a monitor. MONITOR TYPE Select CRT or LCD based upon the type of monitor being used to view the camera. FACTORY RESET If adjustment to the camera’s settings results in poor picture quality, it is recommended to restore the camera to factory default settings.
WPS-700-DOM-A Installation Manual - DISPLAY ID: Set DISPLAY ID to ON to display the CAMERA ID on the screen. This feature is useful when needing to know the ID of a camera simply by viewing a picture. - ID POSITION: Select the position for the CAMERA ID on the display screen by using the left and right arrows “”, “” to move the ID. - PREVIOUS: Return to previous page.
WPS-700-DOM-A Installation Manual SYSTEM DIAGRAM RS485 Cable DVR ID 1 PTZ Controller ID 0 ID 2 ID 3 ID 4 ID 255 WARRANTY 5-Year Limited Warranty This camera has a 5-Year Limited Warranty. The warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified, disassembled or improperly installed.
WPS-700-DOM-A Installation Manual TROUBLESHOOTING If you have trouble operating the camera, first refer to the following guidelines. If the problem persists, contact Technical Support at 866.838.5052. Blurring/ Smudge/ Reflection/ Halo • This dome camera features a gasket that keeps the IR LEDs from reflecting off the inside of the dome and into the lens. When improperly aligned or adjusted, during the day you could see a perfect picture but at night have blurring, smudges or "halo" reflections.
WPS-700-DOM-A Installation Manual The SENSE-UP function cannot be activated • Check if SHUTTER is set to OFF or other value. SENSE-UP function is only available when SHUTTER is set to AUTO. The DAY/NIGHT menu cannot be set to AUTO • Check if AGC is set to OFF. When AGC is OFF, AUTO cannot be activated. The 3D-DNR function cannot be set to ON • Check if AGC is set to OFF. When AGC is OFF, 3D-DNR cannot be activated.
WPS-700-DOM-A Installation Manual SPECIFICATIONS WPS-700-DOM-A — True Day/Night Vandal-Resistant Outdoor Varifocal Dome Camera (650 TVL, SWDR) Video Infrared LED Power Image Sensor 1/3” Sony Super-HAD II CCD Effective Number of Pixels NTSC: 768(H) * 494(V) Resolution Color: 650 TVL; B/W: 670 TVL Min. Illumination Color: 0.03 Lux (50IRE, F1.2), 0.0001Lux (Sens-Up Auto, F1.2) Gamma 0.45 S/N Ratio More than 52dB (AGC Off) Scanning System 2:1 Interlace Horizontal Sync. Frequency NTSC: 15.
WPS-700-DOM-A Installation Manual DIMENSIONS 5.87” 50˚ 3.
120111 © 2012 Wirepath Surveillance
