RFID Smart Reader with Fan-out Box and RF Switch User Manual English
Table of Contents WNC RFID Smart Reader 1. GETTING STARTED .................................................................................... 2 1.1 1.2 1.3 1.4 1.5 1.6 IN THE PACKAGE........................................................................................ 2 INTRODUCTION .......................................................................................... 2 HARDWARE OVERVIEW- RFID SMART READER ............................................ 4 HARDWARE OVERVIEW- FAN-OUT BOX .............
1 Getting Started WNC RFID Smart Reader 1. Getting Started 1.1 In the Package RFID Smart Reader Power Cord Fan-out Box (optional) RF Switch (optional) Power Adapter Note: The Fan-out Box and RF Switch work in combination to allow more antenna connections. One RFID Smart Reader can connect to one Fan-out box and four RF switches. 1.2 Introduction The WNC RFID Smart Reader (the Reader) is suitable for a variety of UHF RFID applications.
1 Getting Started WNC RFID Smart Reader Basic application: You can connect to up to four antennas and use a computer to monitor detected parameters. Advanced application: Use the Reader with a Fan-out Box and an RF Switch to connect up to 16 antennas.
1 Getting Started WNC RFID Smart Reader 1.3 Hardware Overview- RFID Smart Reader Front Panel Rear Panel WAN Connect a standard RJ-45 Ethernet cable to the port to establish a network connection. This feature allows you to configure settings or read the data from the Reader on your computer via a Graphic User Interface. WAN port supports Power over Ethernet (PoE). LAN Currently unavailable. DC IN Connect the power adapter to the Reader via this inlet to power on the Reader.
1 Getting Started WNC RFID Smart Reader 1.4 Hardware Overview- Fan-out Box OUTPUT For RF Switch connection. INPUT Connect to the GPIO port of the Reader. Device 1&2 Sensor data input/output ports for other applications, for example, connecting to entrance and exit sensors for security control. 1.5 Hardware Overview - RF Switch INPUT Connect to an OUTPUT port of the Fan-out Box. RF IN Connect to an antenna port of the Reader. ANT 1~4 For antenna connection.
1 Getting Started WNC RFID Smart Reader 1.6 Connecting the Cables Basic installation: 1. Plug an RF cable into an antenna port and an antenna. The Reader supports up to four antennas at the same time. 2. Connect an RJ-45 Ethernet cable to the WAN port and to your computer for software development interface configuration. 3. Connect the power adapter to the DC IN inlet on the Reader. Once the power adapter is connected to the Reader, the Power LED indicator will turn green indicating the power is on.
1 Getting Started WNC RFID Smart Reader Installation with Fan-out Box and RF Switch: Wistron NeWeb Corporation© 7
1 Getting Started WNC RFID Smart Reader 1. Use an RF cable to connect an antenna port of the Reader to the RF IN port of the RF Switch, and then connect the antennas to the ANT1~4 ports of the RF Switch. 2. Use a DB9 cable to connect the GPIO port of the Reader and the INPUT port of the Fan-out box. Note: Only use a rollover type DB9 cable (not crossover type.) The cable must be shorter than 5m. 3. Use a DB9 cable to connect an OUTPUT port of the Fan-out Box to the INPUT port of the RF Switch.
2 Software WNC RFID Smart Reader 2. Configuration Software 2.1 Access the Management Interface 2.
3 Appendix WNC RFID Smart Reader 3. Appendix 3.
3 Appendix WNC RFID Smart Reader System Architecture Processor System Memory / Ram Internal Storage / Flash TI TMS320DM6446 64MB 128MB Communication USB Ethernet GPIO Indicators N/A 10/100 Base-T (RJ-45) X2 (POE x 1 802.
3 Appendix WNC RFID Smart Reader 3.2 Specifications: Fan-out Box RF System Chipset MC33202DR2G Regulatory and Environmental Compliance EMC certification Certification FCC 47 CFG Ch.1 Part 15 (US) (15.247) ETSI EN 302 208-1 (V1.1.1) (EU) (optional) RoHS / FCC / CE(optional) General Characteristics Dimensions Weight Base Material Mounting Power Consumption 12.5 x 6.2 x 2.6 cm ~250g Aluminum alloy (AL 5052) Wall, floor 0.
3 Appendix WNC RFID Smart Reader 3.3 Specifications: RF Switch RF System Chipset SN74HC139PWR SN74HC240PWR AS221 RF Frequency US: 902 ~ 928MHz/ EU: 865 ~ 868MHz/ KR: 910 ~ 914MHz/ Typical Insertion Loss PRC: 920 ~ 925MHz/ Open:840MHz ~ 960MHz/ 1.2dB Typical Isolation 36dB Regulatory and Environmental Compliance EMC certification Certification FCC 47 CFG Ch.1 Part 15 (US) (15.247) ETSI EN 302 208-1 (V1.1.
3 Appendix WNC RFID Smart Reader 3.4 Pin Definition GPIO port of RFID Smart Reader DB9 Female connector Pin1 5V Pin2 Output port1, 3.2V Pin3 Output port3, 3.2V Pin4 Input port1, 3.2V Pin5 Ground Pin6 Ground Pin7 Output port2, 3.2V Pin8 Output port4, 3.2V Pin9 Input port2, 3.
3 Appendix WNC RFID Smart Reader Device 1&2 ports of Fan-out Box Device 1 Pin1 5V Pin2 GPI_1 Pin3 GPO_3 Pin4 Ground Device 2 Pin1 5V Pin2 GPI_2 Pin3 GPO_4 Pin4 Ground Wistron NeWeb Corporation© 15
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
台灣使用注意事項: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法 規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用 電波輻射性電機設備之干擾
