User's Manual
Table Of Contents
- Introducing the 802.11a/g Router
- Installing the 802.11a/g Router
- What’s in the Box?
- A physical look at the back panel
- A physical look at the front panel
- Connecting the Cables
- High Level Configuration Steps Required for the 802.11a/g Router
- Setting up a Windows PC or wireless client as DHCP clients
- Configuring a PC running MS-Windows 95/98/Me:
- Configuring a PC running MS-Windows XP/2000:
- Confirming your PC’s IP Configuration:
- Connecting More Devices Through A Switch/Hub To The 802.11a/g Router
- Basic Configuration of the 802.11a/g Router
- Advanced Settings
- Managing your 802.11a/g Router
- How to View the device Status
- How to View the System Log
- Security Log
- DHCP Client Table
- Wireless Client Table
- Bridge Table
- WAN Status
- LAN Status
- Upgrading Firmware
- How to Save or Restore Configuration Changes
- How to Restore the System Settings to the Factory Defaults
- How to Reboot your 802.11a/g Router
- What if you Forgot the Password?
- Command Line Interface
- Text Configuration
- Specification
PPPOESessionType=unnumbere
d_link
KeepPrivateLan=enable/disable
UnnumberedIP=192.168.1.1
UnnumberedNetmask=255.255.2
55.0
ISPType=pptp
PPTPLocalIP=11.0.0.10
PPTPNetmask=255.255.255.0
PPTPRemoteIP=11.0.0.1
PPTPUserName=name
PPTPPassword=password
PPTPIdleTimeout=time
PPPOEServiceName: service name for the
connection
PPPOEConnectionType: type of the PPP connection
(‘demand_dialing’, ‘always_on’, ‘manually’).
PPPOEMTU/PPPOEMRU: the MTU/MRU for the
connection (unit: byte).
PPPOESessionType
: type of the PPPoE session
(‘normal’, ‘multiple_pppoe’, ‘unnumbered_link’).
For PPPoE ‘unnumbered_link’ session type:
KeepPrivateLan: keep the private LAN or not
(‘enable’ or ‘disable’).
UnnumberedIP
: the IP address of the private LAN if
‘KeepPrivateLan’ is ‘enable’
UnnumberedNetmask
: the subnet mask of the private
LAN if ‘KeepPrivateLan’ is ‘enable’
For ‘pptp’ type:
PPTPLocalIP
: the local IP address for establishing
the PPTP tunnel.
PPTPNetmask: the subnet mask of the WAN
interface where the PPTP tunnel is established.
PPTPRemoteIP: the remote IP address for
establishing the PPTP tunnel.
PPTPUserName: the user name of the ISP account.
PPTPPassword
: the password name of the ISP
account.
PPTPIdleTimeout: the maximum idle time before the
connection is taken down (unit: minute).
[MultiplePPPoEEntry]
MpppoeSessionName=session
name
MpppoeUserName=name
MpppoePassword=password
MpppoeConnectionType=manual
ly
MpppoeMTU=1492
MpppoeMRU=1492
MpppoeLanType=enable
MpppoeLanIP=2.2.0.0
MpppoeLanNetmask=255.255.0.0
TPIPRange=enable
TPPortRange=disable
TPKeyword=disable
TPNetBios=enable
TPRuleIPRange=50.0.0.0-20
Multiple PPPoE Sessions Configuration
There could be multiple entries (max 7 entries), each
entry contains the following items:
MpppoeSessionName: a mnemonic name for this
entry.
MpppoeUserName: the user name for the ISP
account.
MpppoePassword: the password for the ISP account.
MpppoeConnectionType
: type of the PPP
connection (‘demand_dialing’, ‘always_on’,
‘manually’).
MpppoeMTU/MpppoeMRU
: the MTU/MRU for
the connection (unit: byte).
MpppoeLanType: Enable the LAN type access on
the session or not (‘enable’ or ‘disable’)
MpppoeLanIP: the IP address of the LAN type
network if ‘MpppoeLanType’ is ‘enable’.
M
ppp
oeLanNetmask: the subnet mask of the LAN
76