User Manual

Product specification for DNUA-PO1
Confidential !! Page 9 of 11
(MCS3) 16-QAM 1/2 -74 -84
(MCS4) 16-QAM 3/4 -70 -80
(MCS5) 64-QAM 2/3 -66 -77
(MCS6) 64-QAM 3/4 -65 -72
(MCS7) 64-QAM 5/6 -64 -67
 HT40
(MCS0) BPSK 1/2 -79 -88
(MCS1) QPSK 1/2 -76 -86
(MCS2) QPSK 3/4 -74 -84
(MCS3) 16-QAM 1/2 -71 -80
(MCS4) 16-QAM 3/4 -67 -78
(MCS5) 64-QAM 2/3 -63 -73
(MCS6) 64-QAM 3/4 -62 -70
(MCS7) 64-QAM 5/6 -61 -64
 802.11na
Modulation Code Rate IEEE Spec (1Rx dBm) Typical (1Rx dBm)
 HT20
(MCS0) BPSK 1/2 -82 -89
(MCS1) QPSK 1/2 -79 -87
(MCS2) QPSK 3/4 -77 -84
(MCS3) 16-QAM 1/2 -74 -80
(MCS4) 16-QAM 3/4 -70 -77
(MCS5) 64-QAM 2/3 -66 -72
(MCS6) 64-QAM 3/4 -65 -71
(MCS7) 64-QAM 5/6 -64 -67
 HT40
(MCS0) BPSK 1/2 -79 -84
(MCS1) QPSK 1/2 -76 -81
(MCS2) QPSK 3/4 -74 -79
(MCS3) 16-QAM 1/2 -71 -76
(MCS4) 16-QAM 3/4 -67 -72
(MCS5) 64-QAM 2/3 -63 -70
(MCS6) 64-QAM 3/4 -62 -67
(MCS7) 64-QAM 5/6 -61 -64
Transmit
spectrum
mask
 For transmitted spectral mask for 11a shall be less than –40dBr for fc–30MHz<f<fc+30MHz.
 For transmitted spectral mask for 11b shall be less than –50dBr for fc–22MHz<f<fc+22MHz.
 For transmitted spectral mask for 11g shall be less than –40dBr for fc–30MHz<f<fc+30MHz.
 For transmitted spectral mask for 11n 20MHz shall be less than –45dBr for
fc–30MHz<f<fc+30MHz.
 For transmitted spectral mask for 11n 40MHz shall be less than –45dBr for
fc–60MHz<f<fc+60MHz.
Transmit
spectrum
flatness
 For 802.11a/g the average energy of the constellations in each of spectral lines –16..-1 and
+1..+16 will deviate no more than +/- 2dB from their average energy.
For 802.11n 40MHz mode, the average energy of the constellations in each of spectral
lines –42..-2 and +2..+42 will deviate no more than +/- 2dB from their average energy.
 The transmitted spectral flatness should be with in +2/- 4dB.
Transmit
center
frequency
tolerance
 The transmitted center frequency tolerance shall be ±20 ppm maximum.
Receiver
 802.11a