User's Manual

ManualsBrandsWistron NeWeb ManualsElectronics802.11 a/b/g/n 2x2 USB Dongle

English - 1 -

Connectivity

Wired Connectivity

To Connect to a Wired Network

• You must have a modem/router connected to an

active broadband connection.

• Connect your TV to your modem/router via an

ethernet cable. There is a LAN port at the rear (back)

of your TV.

Broadband ISP connection

LAN (ethernet) cable

LAN input on the rear

side of the TV

To configure wired settings please refer to

the Network/Internet Settings section in the

System>Settings Menu.

• You might be able to connect your TV to your LAN

dependingonyournetwork’sconguration.Insuch

a case, use an ethernet cable to connect your TV

directly to the network wall outlet.

LAN input on the rear

side of the TV

network

wall socket

Conguring Wired Device Settings

Network Type

The Network Type can be selected as Wired Device,

Wireless Device or Disabled, in accordance with the

active connection to the TV set. Select this as Wired

Device if you are connecting via an ethernet cable.

Internet Speed Test

Highlight Internet Speed Test and press the OK

button. TV will check the internet connection bandwidth

and display the result when complete.

Advanced Settings

Highlight Advanced Settings and press the OK

button. On the next screen you can change the IP and

DNS settings of the TV. Highlight the desired one and

press Left or Right button to change the setting from

Automatic to Manual. Now you can enter the Manual

IP and / or Manual DNS values. Select the related item

in the drop down menu and enter the new values using

the numeric buttons of the remote. Press the OK button

to save settings when complete.

Wireless Connectivity

To Connect to a Wireless Network

IMPORTANT: “Veezy 200” USB dongle is required to

use wireless network features.

The TV cannot connect to the networks with a hidden

SSID. To make your modem’s SSID visible, you should

change your SSID settings via the modem’s software.

To Connect to a wireless LAN, you should perform

the following steps:

1. Then connect the wireless adaptor to one of the

USB inputs of the TV.

2. Tocongure yourwirelesssettingspleaserefer

to the Network/Internet Settings section in the

System>Settings Menu.

Broadband ISP

connection

Wireless LAN

adaptor

USB inputs on the

rear left side of the TV

A Wireless-N router (IEEE 802.11a/b/g/n) with

simultaneous 2.4 and 5 GHz bands is designed to

increase bandwidth. These are optimized for smoother

and faster HD video streaming, le transfers and

wireless gaming.

• The frequency and channel differ depending on

the area.

• The transmission speed differs depending on the

distance and number of obstructions between the

transmission products, the conguration of these

products,theradiowaveconditions,thelinetrafc

and the products that you use. The transmission may

also be cut off or may get disconnected depending

on the radio wave conditions, DECT phones or any

other WiFi 11b appliances. The standard values of

the transmission speed are the theoretical maximum

Summary of content (4 pages)

PAGE 1
Advanced Settings Connectivity Wired Connectivity To Connect to a Wired Network • You must have a modem/router connected to an active broadband connection. • Connect your TV to your modem/router via an ethernet cable. There is a LAN port at the rear (back) of your TV. Broadband ISP connection Highlight Advanced Settings and press the OK button. On the next screen you can change the IP and DNS settings of the TV.
PAGE 2
values for the wireless standards. They are not the actual speeds of data transmission. • The location where the transmission is most effective differs depending on the usage environment. • The Wireless LAN adaptor should be connected directly to the TV’s USB port. USB hubs are not supported. You can plug your wifi dongle into the supplied dock in cases where network quality is poor and the wifi dongle needs to be placed to a location with better signal quality. • The Wireless LAN adaptor supports 802.
PAGE 3
Using with mobile devices There are different standards which enable sharing of screens including graphical, video and audio content between your mobile device and TV. Plug the wireless USB dongle to TV first, if the TV doesn’t have internal WiFi feature. Then press the Source button on the remote and switch to Wireless Display source. A screen appears stating that the TV is ready for connection. Open the sharing application on your mobile device.
PAGE 4
If you select the media type as Videos and choose a device from the selection menu. Then select the folder with video files in it on the next screen and all the available video files will be listed. To play other media types from this screen, you can go back to main Media Browser screen and select the media type as desired and then perform the network selection again. Or press the Blue button to switch to next media type quickly without changing the network.