802.11b/g mini-PCI WLAN Module User’s Manual July.
Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp. Pentium is trademark of Intel. All copyright reserved.
FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Important Note This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Code Statement For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. 如果這一個 module 沒有限定在特定的 host，只要是 Mobile 即可的話 IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied.
LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: NKRDRMR81 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules.
Chapter 1 Introduction Thank you for purchasing this 802.11b/g mini-PCI WLAN Module that provides the easiest way to wireless networking. This User’s Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. Features RoHS compliance Operation temperature -25~70oC High speed for wireless LAN connection: IEEE802.11b 11Mbps data rate by incorporating Direct Sequence Spread Spectrum (DSSS); IEEE802.11g 54Mbps date rate with OFDM and 11Mbps with DSSS.
Chapter 2 Installation Follow the steps below to complete the installation: 1. Execute IS_AP_STA_6x_D-1.2.3.0_VA-2.1.0.0_2500_D-3.2.0.0_VA-3.2.0.0_RU-2.0.4.0_VA-2.0.4.0_ AU-1.2.1.0_VA-1.0.4.0_101707_0.1.0.29.
2. Click “Next”.
3. Select “Ralink Configuration Tool”.
4. Select “Optimize for WiFi mode”.
5. “Select “SETUP”.
6. The hardware installation is completed.
Chapter 3 Connecting to a Network 1. Double click the shortcut icon of Ralink Wireless Utility on the desktop, and the RaUI Wireless Network Connection Status’ window appears. 2. Select “View Wireless Networks” and check the available networks.
3. From the list of “Available Networks”, choose one network by clicking the “add connection setup”. 4. You can either select “Unsecured wireless network” or “Security-enabled wireless network”. You need the appropriate username and password to use a “Security-enabled wireless network”.
Chapter 4 Specification Please refer to the other document - approval spec.
