FHD251E IP Camera User Manual
Table of Contents FCC STATEMENT ............................................................................... 1 SAFETY PRECAUTIONS ..................................................................... 3 1 INTRODUCTION ...................................................................... 5 1.1 1.2 1.3 2 START USING THE CAMERA .................................................. 11 2.1 2.2 2.3 3 PACKAGE CONTENTS ............................................................... 5 KEY FEATURES .............
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC Radiation Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator & your body. This device complies with Part 15 of the FCC Rules.
Safety Precautions Please read this user manual before operating this product. The information contained in this document is subject to change without notice. Features or specifications may be different depending on the type of product model purchased. Safe Use of This Product Carefully follow the warnings and safety notices presented within this manual.
• • • • • • • • • • • This product needs only an occasional wipe with a dry cloth. Avoid high-moisture conditions and keep away from liquids and humidity. Do not install or use the product where it is exposed to direct sunlight or heat. Care must be taken when using the device in close proximity to personal medical devices, such as pacemakers and hearing aids. Do not use this product in environments where there are potential explosion hazards.
1 Introduction 1.1 Package Contents Thank you for purchasing this product.
1.2 Key Features FHD251E • • • • • • • • • • • Full HD 1080p @ 30 fps (1920 × 1080) Visualization in total darkness up to 15 meters Switchable IR cut filter for vivid color during the daytime Light sensor to automatically detect ambient light conditions Motion detection Digital PTZ HDR LDC Power over Ethernet Waterproof IP65 Easily connects to home-network environments WFB100S • • • • • Internal Power Module, V-in: 120 V, V-out: 48 V Wi-Fi: 2.4 GHz IEEE 802.11n 2 × 2 RJ45 Ethernet connection IEEE 802.
1.
LED functions LED Color Red Blue Green Green Green Function Description Pre-boot Operating system booting Post-boot; no network connectivity Standby; encoder recording locally Streaming to the network 8 Status Solid on if “power OK” Blinking 1 Hz, 50% duty cycle Blinking 4 Hz, 50% duty cycle Solid on Blinking 1 Hz, 50% duty cycle
WFB100S Light guide Button Ethernet port LED functions: LED color Function description Blue Normal operation and connected Blue Power up and during firmware download Blue Firmware download complete but no connectivity Blue WPS mode activated 9 Status Solid on Fast blinking, 4 Hz, 50% duty cycle Slow blinking, 1 Hz, 50% duty cycle Off
10
2 Start Using the Camera 2.1 Assembling the Camera & the Wireless Adapter Follow the steps below to set up your camera hardware and ensure that the camera operates properly. 1. Attach the camera bracket to the camera by gently tightening it onto the camera. Caution: Ensure that the camera is securely fixed; otherwise it may fall and cause damage or injury.
2. Remove the grommet and the cap on the rear side of the camera. 3. Insert the Ethernet cable into the camera’s Ethernet port and connect the other end to the wireless adapter, then place the grommet back and screw on the cap.
4. Plug the wireless adapter into an electrical outlet.
2.2 1. 2. 3. Connecting the Camera to a Network After inserting the Ethernet cable into the camera’s Ethernet port and connecting the other end to the wireless adapter, the adapter will be able to supply power to the camera when plugged into a wall outlet. Press the WPS button of the AP that you want to connect to, then press the adapter’s button to connect to the AP.
2.3 1. 2. Rebooting and Resetting the Camera and the Wireless Adapter Press and hold the button on the wireless adapter for 0 seconds–3 seconds or over 20 seconds. For factory reset, press and hold the button on the wireless adapter for 10 seconds–20 seconds.
3 Appendix 3.1 Specifications and Compliance Model FHD251E Resolution IR LEDs IR LED Illumination Range Sensitivity Sensors Lens Status LEDs FOV Operating Voltage Ambient Operating Temperature Storage Temperature Dimensions Weight IP Rating PoE 1080p (1920 × 1080) @ 30 fps 12 pcs. 15 meters 0 lux when IR LED is on (black & white video). CMOS 1/3” 4 megapixels 6 glass 1 pc (Tri color—red, blue, and green) 138° (D) V-in: 48 V (DC) –40 °C to +65 °C –40 °C to +65 °C 77.05 mm × 115.97 mm × 79.
Model WFB100S CPU 2.
3.2 Troubleshooting Problem Solution The button has no response. The LED blinks slowly after the WPS process is completed. 1. Check the Ethernet connection status. 2. Plug out and plug in once to reboot the wireless adapter. 1. Check the Ethernet connection status. 2. Restart WPS pairing and make sure the AP router is in signal range and is in WPS mode.
3.3 Obtaining Technical Support While we hope your experience with the FHD251E IP Camera is enjoyable, you may experience some issues or have questions that this User Manual has not answered. If you have a problem with the FHD251E IP Camera, please contact us at: Tel.:+886 3 666 7799 Ext.: 3214 E-mail: Jacky.Liu@wnc.com.tw Mobile: +886 916 324 575 Website: www.wnc.com.tw 3.4 Disposal Instructions WNC is committed to responsible environmental stewardship.
